You will see that many of the tips and procedures used are universal for skill sets "every mechanic should know" and that the biggest value to my videos is the teaching of these skills that are not found in a service manual. I often get asked this question: Q: How does one learn these skill sets "every mechanic should know" if they are not found in a manual? A: NUMBER 1.....GET DIRTY and start wrenching. -Ask questions -Find a seasoned craftsman to mentor under -Tech schools can significantly speed this time up -Research, read, watch YouTube videos Tip: You will never learn it all from one source or in a short time period. No matter what craft you are trying to master, YOU must be dedicated and put the time in. THERE IS NO BETTER WAY TO LEARN THAN DOING! I will say it again, you must actually do the work to master it. You cannot just watch or read about it and master anything. You want to be a master bike builder, mechanic, welder, nurse, carpenter or you fill in the blank? -Don't take for granted opportunities to learn deeper -Be humble and seek advice -Be intentional with your learning plan -Don't blame a school, job or your parents for not giving you ever answer, go get it!
I teach a motorcycle/powersports technician program at Western Iowa Tech Community College in Sioux City, Iowa. These videos are used for review of labs for students and creating a deeper understanding of the lesson/skill set. As there is often more than one way of doing something, may you enjoy this free information as much as our students do in person. PLEASE HIRE OUR GRADUATES!
If you would like more info on the program feel free to contact me @ 712-274-8733 ext 1204 or email [email protected]
Are you interested in a career in the motorcycle industry? Click here for information on a great technician and parts specialist training program: https://www.youtube.com/watch?v=YFWKqGzakiw
So, I need to go ahead here and install my bowl, and then get my diaphragm started on
there, plunger, and I like to go ahead while I, so I don't forget later on, I'm going to
go ahead and get my rubber boot on there.
Make sense?
Yep.
Okay, this is a good point here.
Listen to me.
I'm doing all kinds of yapping, all kinds of teaching, some people call it, I don't
know about you guys, but I know that I can get into trouble by not having stopping points.
You with me?
And so what I'm going to do right now, since I'm getting ready to close a part of the carburetor,
what you want to do, I'm going to just do a kind of a quick inventory check to make
sure there's nothing I didn't forget in here.
Right now is a good time for me just to do a double check.
Here's another thing to think about where we get into trouble or where we go wrong,
is brackets on the motorcycle.
You dirt bike guys, you remember how many clamps you had for doing hoses?
Remember that?
And where do we figure out, you know, does the clamp go here, does it go here, here?
I have to use what to determine that?
Parts fish.
The parts fish.
I want to take the carburetor in the right direction and I want to figure out, okay,
Honda or Suzuki, Harley, whatever, had a clamp over here, I want to put that in the right
spot.
Contact with a clamp or a hose that shouldn't be there, I'm going to have a problem.
So it's important that we're diligent on following that microfiche and putting stuff in the right
way.
On this one here, we've got nothing to worry about, so we're going to go ahead and as soon
as I can, I like to get this bowl bolted together.
Why?
So nothing can get into it?
And now what we're going to do is we get to do two tests.
Okay, now we're doing a wet bench test, okay?
Before we were just getting the float needle wet and what we're looking for, if that float
needle was sticking, we would actually have fuel pouring out of here, out of the emulsion
tube.
Make sense?
Yep.
Okay, the other thing that I'm looking for right now is I'm going to go ahead and I'm
going to look at the bowl of the carburetor all the way around it and make sure that the
seal on the carburetor bowl is doing its job.
Does that make sense?
Mm-hmm.
Now look at me.
Back the camera up a second.
You guys are going to think I'm crazy, okay?
Now here's something I like to do too.
This carburetor in the manifold, okay, when this carburetor is on the motorcycle, it actually
on its kickstand sits like this.
Does that make sense?
Because the carburetor is on the right side of the motorcycle.
So here's what I like to do is I like to take with my fuel hooked up, bench testing here,
and go ahead and tip it sideways.
Look for a leak.
If I have any leaks anywhere around here, now's my time to catch it.
If I only check it like this and the fuel level never gets above the gasket, am I going
to be able to check it?
Nope.
Nope.
So then you take this like so, and you're going to take from this position, and I'm
going to do what I call a kickstand test, okay?
But let's do a crash test.
It should leak.
You see how it leaked out?
Yep.
Okay.
It should leak.
We're going to do one final test.
You are going to focus in on our accelerator pump.
Now we have actual fuel in there.
Brr, brr, brr, brr.
You see how it took a couple of times?
Yep.
So that was the priming.
And you'd want to do that on the bike so that the customer doesn't... Obviously, we're
going to test any bike on the bench and take it for a test drive.
See how much hits that plate?
And do you notice how even when I do just a little bit of throttle, I get a little puke
of fuel?
Yep.
You know?
And then you've got your brr.
Okay.
That is how you properly test a carburetor for leaks and integrity and all that other
good jazz.