Restoring a Chippendale Chair - Thomas Johnson Antique Furniture Restoration

Thomas Johnson Antique Furniture Restoration
41 followers
1 Video View·Jul 24, 2012
Tom Johnson of Thomas Johnson Antique Furniture Restoration in Gorham, Maine, provides a detailed video on repairing a structurally weak joint in this antique Chippendale chair. Tom has been restoring furniture professionally since 1979. Visit our website at http://www.thomasjohnsonrestoration.com, call us at (207) 222-2266, or write us at [email protected]. And for those on the west coast looking for custom framing, be sure to check out Tom's daughter's shop, https://www.emcollier.com (@emcollierframes on Instagram).
This is a really nice antique mahogany Chippendale side chair.
It's got a real problem.
This leg has broken off entirely.
Here you get a pretty good idea of what's going on here.
The chair has through tenons.
You can see the tenon from this rail right here.
That's a wedge and a tenon.
And the tenons are also pegged.
Like a lot of chairs, they've cut away so much wood to accommodate both tenons
that it's not very strong.
Somehow, this leg was broken off.
So I'm going to glue this.
The first thing I'm going to do is take the back of the chair off.
These joints are loose anyway.
So I'm going to draw out these pegs, take this chair apart.
I'm going to glue this back where it belongs.
And then I've got to cut in some wood
that will come across here and give it some additional strength.
Notice I'm using, I don't know if you can see,
I'm using a drill bit a little bit smaller than this peg.
I'm going to leave the sides of that peg around there
so that I can get out exact, not over-drill it.
I can still drill it, but now I've got the exact hole.
Okay, the next step is going to be to glue the broken leg back where it belongs.
And then after I do that, I'm going to probably route in here
to put a new piece of wood right across here.
And I may do something on the outside corner as well in this area here
where it's got to get something in there to give it some strength.
And always when we're restoring antiques, we use hide glue.
But in this particular case, to glue this piece back where it belongs,
I'm going to use epoxy.
I want to maximize the strength.
I need as much strength as I can get out of this glue-up in this leg.
Even though I'm going to cut in and put some new wood in,
every little bit can help.
Using the router, I'm going to cut in here across the break
and get a new piece of mahogany.
I'm going to go in this inside corner here,
and I think I'm also going to do this outside corner here.
I've got to get some kind of solid wood across those breaks.
What I've got is a jig, which is just a piece of plywood
with a rectangle cut into it, which I'll clamp down to the chair.
And the router base has a template guide,
which will run inside that jig.
I've marked on the chair here with a piece of tape
where I want the cut to be.
I'm going to cut right along here.
So I'm going to make a new template for this cut.
So here's a scrap piece of MDF,
and I've drawn a rectangle on here that I want to cut.
It's important that all these lines be straight,
because they're going to guide the router bit.
Okay, now I've got my template.
I'm going to clamp this down over the area that I want to route out.
So now I've marked out in tape here on the chair
where I want this piece of wood to go that I'm going to glue in here.
And I will clamp my template down and line it up.
Clamp it down exactly.
Okay, here's my cut after just the router.
You can see that I've cut just down to the tenon of the back rail here.
I don't want to cut into that tenon. I cut right down to it.
So now I'm going to take a chisel and square up these shoulders
and clean it up and glue a piece of mahogany in there.
I have a nice old piece of mahogany here
that ironically came out of a chair that eventually had to lose its legs.
So I think I can get this piece, my replacement piece, out of this.
Okay, I've got my piece of mahogany, all sized, ready to fit in there.
I'm going to glue it in.
I'm going to use yellow glue for this part of the glue-up.
I'm going to let this dry overnight
and then I'm going to do a similar operation on the opposite corner, on the outside.
Okay, so here's my new piece of mahogany
glued up across that break in this thickest part.
And now I think I'm going to do the same thing on this outside corner.
There's a pretty thin strip of wood here because of that through tenon,
but it is completely broken across here.
I think I should put some wood in at least here, across there.
Maybe it'll add some strength.
Okay, so now I've got this corner cut out.
I've got to clean this corner up with my chisel
and then get a piece of wood I can glue in there.
Just like my spline on the other side,
I'm going to glue this up with yellow glue.
Okay, so now my repairs look pretty good
and the next step is to put this back together
and the first step of that is I will put it together dry, without glue.
I want to say something about adhesives.
This is kind of an interesting case, this chair repair,
because if you remember, this leg was broken completely off
with just ragged edges of end grain.
So when I glued that back where it belonged,
I used a marine grade epoxy
because it was really a terrible woodworking joint.
It didn't really have much going for it.
I wanted to give it all the strength I could,
so I used epoxy for that.
When I put my splines in across that break,
I used conventional yellow glue.
I knew that I had a very good joint,
a lot of wood-to-wood contact,
and I felt that the best, strongest glue for that is yellow glue.
Now, as I go to glue this chair back together,
and I'm gluing the original joints,
I'm going to use hide glue.
Because that's the type of glue,
or the class of glue, if you will,
that they would have used when this chair was built.
Three kinds of adhesives for the one repair,
each one for a different reason.
My glue-up looks pretty good.
Everything's together fine.
Now I've got to clean off the glue.
I've got to redo these pegs.
I've got to drill these.
They're an oddball size,
so I may have to make some mahogany dowels.
This is a little trick.
I didn't want the drill to chatter and go out of my hole,
so I actually put the drill on reverse,
and I'm going to start this hole on reverse,
so I stay right where I need to be.
Now that it's started,
these holes I drilled are 9-30 seconds,
so I'm going to make...
I have a piece of mahogany here.
I'm going to make some approximately 9-30-second dowels.
I'll start off by cutting this wood square
to a slightly larger dimension.
Okay, now I've got all my sanding and prep work done.
I'll do a little check of the color here.
My new pieces are a little light,
so I think before I seal this with some shellac,
I'm going to try putting a little bit of stain
on my new pieces.
Okay, now I'll seal
all my two touch-up areas with some shellac.
Now I'll sand my shellac with a little 320.
I'm going to tone those areas a little bit
with some dark walnut toner.
Now I'll just seal in my touch-ups
with some very low luster lacquer.
Okay, so my last remaining task
is to go over this with my beeswax polish
and a little steel wool.
I'll go over the entire chair.
Okay, here it is.
If you remember, this chair came in.
This leg was completely broken off.
I glued it back,
and then I cut into the outside corner here
and the inside corner
and put some new wood across that break.
It certainly seems strong now.
Okay, looks pretty good.
