What is the perfect bolt pattern for highlining? Equilateral triangles might be the best!

HowNOT2
100 followers
2 Video Views·Jan 23, 2019
Straight bolt patterns for highline anchors equalize quite poorly and BFKs are random at best. If it really matters what is the best pattern to get perfect equalization. 4 bolt patterns did well with giant parabolas and 3 bolt patterns did well with an equilateral triangle. Check out the numbers on each leg of our anchors in this video.
If you have ideas for videos, please leave a comment below or if you want to make a video to be featured on HNTH please message me on my personal fb page https://www.facebook.com/ryan.jenks.35
Find slackliners near you at https://www.hownot2.com/slacklinegroups/
Thank you to my Patreon supporters who donate $1 per episode at https://www.patreon.com/howNOTtoHighline
I'm tired of drilling holes in my patio,
but I want to find the perfect bolt pattern.
So I'm here at the park aerating the lawn
in this episode of How Not to High Line.
Hi, I'm Ryan Jinks and welcome to the park.
We are going to test different bolt patterns
by using these 14 inch long by three eighths inch lag bolts
with these chains on them.
And we can do those in different configurations
without putting a bunch of holes in my patio.
And here I have a seven ish meter long distance
between my anchor and the tree
to give us a little bit more of a realistic pull
from the slack line rather than from my backyard
where I only had about a one meter long slack line
pulling on our anchor.
The first example I always like to show
when doing equalization is a straight bolt pattern here.
You can see how it's a little bit less
than two feet across the bolter in the grass right there.
I added a quick link here
to make this a little bit easier to attach.
Now we have Andy Lewis's four dynamometers
and my one dynamometer.
And I'm just using figure eights here to do an equalization
because those are the most easy to duplicate
when you're watching a YouTube video.
The way I thread my sliding X is to go up the dyno,
down the shackle, up the dyno, down the shackle,
up the dyno, down the shackle, and just continue that.
And then only this strand right here
is crossing over the other three
which are not touching or crossing over each other.
And that makes it sit mostly flat.
So the math here is three kilonewtons at the master point.
And on a straight bolt pattern,
you have 0.3 kilonewtons on the outside
and 0.7 kilonewtons on the inside.
This is a little bit more than double the force
on the most centered bolts.
Okay, so now I changed the same bolt pattern
to a dynamic rope.
The rope we were using is a very static canyoneering rope.
It's a Dyneema core,
just like soft shackles are made out of,
with a Technora sheath.
So this is actually like 20-ish kilonewtons,
eight millimeter rope,
rather than a standard eight millimeter climbing rope,
which is only 14 kilonewtons.
This is bomber.
However, I am asked that a dynamic rope,
would it equalize better?
And I have moved this around.
And I shook it back and forth aggressively.
We're at three kilonewtons right now.
And no, it doesn't.
We have half a kilonewton on the outsides here.
And in the middle, we have almost one kilonewton.
It's significantly consistent
by pulling the things most in line with it.
Now here is the same 9.2 millimeter dynamic rope,
but it's 11 feet long.
And I don't know why you would ever do
a sliding X 11 feet long,
because you would need whoopee slings that are gigantic.
However, three-ish kilonewtons here.
And the theory is that because they're so close
to each other in this distance here is so far,
it should be pulling evenly.
Well, is it?
Hmm, half a kilonewton on the sides
and one kilonewton here and 0.89 here.
Okay, so I just shook it violently
to see if I can get it to equalize any better.
And yeah, it didn't do, yeah, it didn't do anything.
This is still pulling more than double in the middle
because it's most directly in line.
So the longer your anchor does not compensate
for the principle of the most directly in line
will hold the force.
Okay, back to our 10 meter long,
eight millimeter static rope.
And what I did here is I extended this
with what I would call chain link.
This is what I have to imitate chain link.
You don't wanna use aluminum carabiners
in your anchor like this, but it's very static.
And if you did a bunch of quick links or something,
extending a straight bolt pattern out on the sides
to simulate the center bolts being further back.
Okay, and this, I had a theory that this would work.
This is only, by the way, a four,
four and a half foot long anchor
with my 10 millimeter, 10 meter rope.
3.7 kilonewtons on the MasterPoint.
What does the verdict say?
Ah, shit, I thought this was a good idea.
Half, one, more than one, and 0.6.
Now I changed it to sliding Xs with shoulder length slings.
And I have here, these are the Mammut's new ones
that are built like span sets,
where the inner core goes around and around
and around and around like a span set
and has this abrasion resistant sheath over it.
This is 24 kilonewtons strong
and I would be pretty comfortable highlining on this,
except for the fact that I have aluminum carabiners here.
Aluminum doesn't handle cyclic loading
as good as steel does.
Steel bends, these explode.
So if you had steel here or quick links,
which quick links are made out of steel,
I would highline on this if there were whoopee slings
going from what would be our bolts to our MasterPoint.
So this is actually a really neat setup
and I'll show you why.
3.26 kilonewtons and it bisects the thing
so there's no more center bolts.
And then it evenly pulls 0.81, 0.82, 0.82, 0.78.
That's literally perfect.
And you can see how bisecting those angles down here,
how much that really, really helps.
So the benefit to knowing this
is if you come across a straight bolt pattern,
which is super common,
and you notice that they're not good bolts,
this is a thing you can do
to make sure you're pulling on them evenly.
Especially if you're doing something complex
like a space net or a rope swing when it really matters.
And this is also good for cams,
if you're rigging off of cams.
Now, a single point to me is two cams.
So two cams would be this point here
and the two cams would be up there coming to a V.
And so you would have eight cams total
and you would take those points
and you would go V to this V to this V.
And that's called a cascading anchor.
And that pulls on all those cams fairly evenly.
And of course you would whoopie sling
directly to all the cams.
And you would do either the set of cams
or you would do each one individually
and have eight whoopies,
which would be a clusterfuck here at the master point.
But it depends on how good of the rock
and how good your cams are
and how confident you are in placing them.
You get to decide all that when building your anchor.
And now for my favorite configuration,
the oh so simple figure eight.
Figure eight with no knot in the tails.
The tails just go through and then you tie it in, whatever.
We show BFKs in other videos.
3.5 kilonewtons at the master point.
And I did my best.
I tried so hard to tie this evenly
and I kicked it around afterwards.
Anyways, it's not even.
These are almost double in the middle, just like before.
But you know what?
That's super good enough.
A bolt is 24-ish kilonewtons.
These little six millimeter guys are like 30 kilonewtons.
Your rope, your BFK, we did some tests on these.
Normal eight millimeter static ropes
broke at like, I don't know, 14,000 pounds.
But super strong.
Stronger than any of your webbing
you're ever gonna attach this to.
So if you're not worried about each individual point,
if you're not working with really soft rock
or dealing with ice screws and glaciers
or dealing with cams in weird situations, this is fine.
You have like a 20 to one safety ratio.
And it's redundant as hell
because any of these strands could break
and it's isolated because of this knot.
I highly recommend the BFK
for almost every anchor that you ever do.
It's just nice to know what's going on
with the forces in each strand
in case you have to make hard decisions.
Okay, let's try this bolt pattern here.
What I did was I put the slack line in line
so I know what center is, which is very important.
And then my two outside bolts are exactly one foot apart.
And from the back to the side is 12 inches apart
from that bolt to that bolt.
Now it's important that a half inch bolt
has 10 diameters apart from each other.
In English, that means half an inch times 10
is five inches apart from each other.
That would be five inches apart.
And you can see here that we are more than five inches.
I did six inches.
I put the three right in the middle of the slack line
and I'm even between the two.
So these are a safe distance between.
These are as far away from this
as they are from each other on the outside.
So our anchor is 3.08 kilonewtons
and it's just our 10 meter long static rope
in a sliding X.
And we have 0.6 on the outsides
and 0.7 and 0.9 on the insides.
That is equalized a lot better,
but that's still not perfectly equalized.
And it shows that this,
it's so common for us to do like a curve
where we go like this,
like it'd be this perfect arch
and like a snow cone or something
and all coming down to a single point.
But you can see here, it's more like a parabola
where it goes from here all the way up and back down.
And I'm gonna probably put these even further back
to find out if we can get those
to pull exactly the same as these.
Okay, so I moved the back bolt 16 inches
instead of 12 from the outside
and we have 3.76 kilonewtons,
0.6, 0.7, 0.9, 1.3.
Boy, I am so confused.
How far back do those back bolts need to be
before they share the damn load evenly?
Okay, so I moved them really far back.
These are one feet apart on the outside
and the bolts on the back are two feet behind those bolts.
And our master point is 3.44 kilonewtons,
0.8 on these outside ones and 0.8 on the back ones.
That is pretty exciting.
You can see here that we have two feet here from this bolt
if you go directly back.
And of course, these have to be spaced out
at least the minimum five inches apart.
That is really far back.
That is quite a big parabola,
but you can see here that we have
really, really good equalization.
Okay, the same configuration with the back bolts
to twice as far back as the outside bolts are close.
We have a BFK 3.2 kilonewtons, the master point,
basically 0.4, 0.7, and then 0.9 evenly back here.
That's not terrible.
And I do like the simplicity of having isolated legs
even though they're not perfectly equalized.
It's okay.
BFKs are random at best.
I'm sure I could tie this three different times
until I get an even load, but that's just how BFKs go.
It's just really hard to get them to equalize.
And if it really matters, you need to do a sliding X
or a cascading anchor with whoopee slings
if it really, really matters.
Okay, so I completely moved areas.
I was over there and now I've built an anchor over here,
sliding X, same dimensions as we were successful
on the other side, 2.7 kilonewtons to see
if it's replicable, if it's consistent,
if it's gonna give us the same results,
half a kilonewton on the outside, 0.7 to 0.8.
Close, damn it, but not perfect.
This is one foot apart here
and two feet apart from here to here.
So on this pattern, I split the closest ones
out an additional foot.
So they're two feet apart now
and the back ones are two feet behind those.
We are at three kilonewtons, 0.7, 0.8,
six, seven, and 0.8 and 0.7.
It was actually really helpful
to spread out these outside bolts.
This is a nice pattern.
We have nice angles on our sliding X here.
And for our final bolt pattern, F3 bolt pattern.
Has anybody even asked why we use four bolts?
Because technically one bolt has a five to one safety ratio
for any force you put on a normal highline.
Two is redundant and three is overkill.
I actually don't know why we've done four bolts.
I think that was a lack of knowledge back in the day
on how much force these things actually held.
But if you look here,
we have 2.3 kilonewtons on the master point
and these are two feet apart,
two feet here and two feet here.
So that is a two foot triangle
or a triangle with two foot legs,
0.78 and 0.82 are pretty much the same and 0.71.
A triangle pattern, a three bolt triangle pattern
might be the new bolting standards for highlining
since we know that things are, especially in Goodrock,
things are plenty strong, it's very redundant
and this sliding X is very equalized.
Here's our final triangle three bolt pattern with a BFK.
Does it equalize any better?
2.2 is the master point, 0.72, 0.88, 0.71.
That's pretty good considering BFKs are equalized at best,
but I'm pretty happy with the three bolt triangle pattern.
So I find that my three bolt triangle bolt pattern here
is actually pretty good, I really like it.
And let me know if you think that can be a bolting standard
that we use in our highline community
as long as we have Goodrock
and I assume you're putting in good bolts.
Let me know in the comments below
the flaws you think are in my park science
and what other stuff you think I should try.
But as you can see, equalization is all over the place
and if you're pulling on one thing
more than the other unevenly,
you could rip stuff out and you might die.
Therefore, you shouldn't highline.
Hey, thanks for watching, but don't be an idiot
and try slacklining on a few lag bolts
just because you saw me cranking down on them.
They do come out,
you do have to put quite a few in to make that work.
Don't be an idiot and rig sliding Xs
without some sort of a backup to them like whoopee slings,
or you will shock load your other bolts
if one were to break and then they might all come out.
And don't be an idiot and try learning everything
about highlining from a guy you don't know on YouTube.
Please find a slackliner near you
so you can learn this stuff in person.
But if you like slack science or rigging,
please consider making a video
and message me on Facebook and we can collaborate
and we will share it here on how not to highline.
I think there is a lot to learn
from everyone who loves doing this stuff.
So hit me up and maybe we can get some more people
on how not to highline.
Don't forget to follow, like and subscribe
depending on whatever platform you are on.
Cheers.
