Once you drill holes in a rock, they are there forever. Consider carefully IF and WHERE you place bolts before bolting climbing routes or when you establish highlines. See our EQUALIZATION IS A MYTH series on our channel for bolt patterns as that determines where the holes will go as well. PLEASE READ THE BOLTING BIBLE BEFORE BOLTING https://www.hownot2.com/boltingbible
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break. This all couldn't happen without you!
Thank you Friedi Kuhne for the intro and Nick McPherson for editing.
Sup guys. This episode is going to be just like Swiss cheese,
cheesy and full of holes. When you install bolts for highlines,
holes matter a whole lot.
I'm Ryan Jinks and welcome to my living room. Today, we're going to,
today we're going to talk about bolts and the position of them,
where they need to go and how to consider all this before you put bolts in
rocks that are going to last pretty much forever.
Once you stick in holes, they're permanent. You can always change bolts,
but you can't really change the hole. You can always add glue in it and epoxy,
but it still looks bad over time.
And after a hundred more years of all of this,
and every 20 years we're putting in new bolts and new holes,
it's kind of going to start looking like Swiss cheese.
So let's consider where we're going to put all this stuff.
The position I have right here with four bolts straight line is a really common
bolt pattern that we've had for years. I live near Yosemite.
If you're going to Yosemite, come visit me in Lodi, California,
but this is really, really common from where I'm from.
Now if you're in Moab, Utah,
they put the bolts pretty far back because the sandstone is soft rock and they
don't want the rock to crumble near an edge. But in my situation,
we've had this and we've learned in the previous videos,
series that we've done about equalization is a myth.
Equalization is not a myth.
We just kept changing bolt patterns and forces and stuff like this to see what
would equalize all these bolts because four bolts in a straight line do not pull
evenly. They put most of the force on these center bolts.
So really the biggest thing we're going to talk about is the master point.
Where do you want the master point to be? What I have here is a 10 meter long,
eight meter millimeter wide diameter roller and what you do in these M12
hangers from boltproducts.com is you go through and you build yourself a BFK.
Whoopie slings used to be a thing when we tried to equalize and realize that
doesn't actually happen.
You just tie a really nice BFK and it will pull on stuff even enough.
So you can see here that my BFK is right here on the edge and I like that the
most.
I would even consider putting it right here because my web lock will be here.
My webbing will be out here and so my webbing isn't going to rub,
get abrasion and break, which is the number one risk of a highline failing.
Very important to pad everything.
But this big fat knot is not going to cut through very quickly.
Still want to pad the crap out of it and you probably put a bag under it to kind
of lift it up. It was a little bit easier to work with this.
I've seen too many times master points a full meter out away from a clip edge,
which makes tensioning and getting on and off kind of sketchy.
Even if you have a personal anchor,
you don't really want to be taking a whipper on it.
So it's nice to have the master point right, right here near an edge.
How do you accomplish that? In Yosemite, we have our bolts right here.
You have to work hard to not have it too far out and if they were pretty far
back, you could always adjust the rope,
but you have to consider this part of it before you actually put the holes in.
I heard there was a highline in Colorado that had bolts right here next to the
edge. And when you're building an anchor,
you don't want to have something that's more than 45 degrees or the forces
exponentially get stronger. Ironically,
we made a sport out of a death triangle or out of a bad angle,
which is what a highline is. But it's still, when you're building an anchor,
you do not want that. So if you have the anchors out like this,
that is creating almost twice as much force just at this angle than it is in
this position. So after a lot of tests on equalization is a myth,
we discovered that three bolts is plenty.
So after our series equalization is a myth,
we kind of discovered that one bolt was almost a 10 to one safety ratio.
Two bolts is redundant and three is overkill and we love overkill,
but four is ridiculous and that's a lot more holes than we need.
And in the leaf, no trace spirit,
unless you're dealing with some pretty soft rock, I don't recommend it.
It's not like it even equalizes anyways.
And most of the force is on two or three out of the four.
So here we discovered that a equilateral triangle or even having this back bolt
even further back is going to create more equalization right here,
especially when it's a sliding X.
Now it still helps in this configuration.
If you're going to do a BFK to do a triangle,
the most center bolt in line is going to see the most force and the bolts closest
to the anchor is going to see the most force.
And you can see how this cancels each other out because the closest ones and the
most center ends up evening out.
You can see here that I actually put my BFK a little bit closer to me and that
my web lock is still hanging out this far past the edge.
And so my webbing has no risk of abrasion at this point.
Even the soft shackle on here doesn't have any risk for abrasion if this tape is
signifying the edge.
Now I never leave this stuff unpadded and I would put a haul bag or something
underneath here.
So it really keeps it lifted up and off and I secure it down.
I don't secure my padding over the top of my anchor because I want to be able to
inspect this.
Some people wrap the whole thing up and you can't see shit and you don't know
things safe when you get on.
And this is a tailless figure eight,
whereas I don't tie a fisherman's in a knot here and then tie my figure eight.
It's actually pretty neat because that tail I'm not using,
but here I have a locking carabiner that I put on here for a personal anchor if I
wanted to make it permanent part of the rig.
Now of course it's not ideal to be falling like this,
but the rope's not going to break in this scenario and it's nice that people are
clipped in when near a cliff edge.
And a quick note is the soft shackle here at the master point,
the ropes are not rubbing and so there's no rope on rope abrasion in this
situation.
Whereas like if you tied your leash in a figure eight and slipped it over the
highline,
that rope sliding over the webbing would get you killed.
That rope on rope abrasion will cut things.
But where things are not moving,
just like when you tie your leash into your harness,
that's technically rope on rope.
If things aren't moving,
it won't cut through.
Another option to consider is two bolts.
Now don't beat me up over this,
but this bolt is pretty strong and if I put this in granite,
two is redundant.
And so there are some highline locations that do have two bolts and it is kind of
nice because in this situation I still like to be okay in this situation.
It just takes a lot less rope as you can see how much rope I have left over.
I can even tie it off to a tree back there if I wanted.
But if you are going to use two bolts and keep it as minimal as possible,
make sure you're using some pretty bomber bolts.
We are going to test a lot of bolts on bolt busters and that is Slack Snap's
sister.
We're going to test hundreds of bolts and we're going to find out what's safe
and our limitations.
But the quality of rock and the density of the rock is a huge
factor in how strong your bolts are.
Most rock fails before the bolts come out.
So you just have to get a consideration before you put in your holes.
All this needs to be considered before you start drilling your Swiss cheese.
Now you'll notice that my web lock is getting further and further away from the
cliff edge. And in this situation you have to remember,
this is more about building anchors than putting in bolt holes.
This shit stretches. If I could really pull on this,
this thing would go out almost to the where we're after tensioning.
This would be,
the web lock would be completely over the edge and it's still,
it's really nice to have this close and right here when you're working with it.
And what I do is if I don't have any soft goods, jackets or leftover webbing,
I like taking these fabric grocery bags and cause you really can't afford to
have your bag slip. Uh, you'd have abrasion.
Uh, you don't like to wrap this stuff too much. It depends on your situation.
If I go like this and I can fill this with sand,
fill this with soft goods, whatever. And I can, uh, clip that off to there,
clip that off to there so it doesn't shift.
And right there is really nice to be able to clip in.
My rings can slide all the way to here. Walking off is dangerous,
but if people decide to do that,
they're not trying to jump this one meter gap. This is really, really nice.
My bolts are not too far away, but they're also not too close. If my bolts
were right here,
it would be just near impossible to create something that wasn't a meter or two
away from this, which would be just be difficult to rig.
So if the angle is supposed to be small and you want it to be, you know,
the bolts close to the edge, not too far back, whatever.
And why don't we put them this close together?
You probably never see that. And let me explain why.
You need 10 diameters of space in between them.
So if these are generally working with half inch bolts,
that is five inches away from each other at the minimum.
How they quarry stone,
how they harvest stone is they'll puncture holes like perforated paper and then
break it off. You don't want to put holes right next to each other.
The forces that are created in the rock are like a vector.
This is a V shape. And if they're too close to each other,
those V's intersect, then you're going to weaken the rock.
And remember the rocks holding your highline up, not your bolts.
The bolts are holding the rock. Now, if we want to spread these out,
and let's say you're convinced straight lines, they're not going to kill anybody,
but you have to consider where the highline is going to go.
Now we've talked about master point as far as distance from the edge,
but let's talk about master point in a direction.
If the highline is going that way,
you don't want to set these this way because all the force is going to be on the
closest bolt here. You would want to turn these things in.
You want the center bolt to be in direction of the highline.
Now these are going to be used for multiple use.
You can't just put it with the center bolt further
back for this line and for this line, unless you do the equilateral triangle.
So if you try to make it like,
you do that,
you can find a happy medium.
And now this is a center bolt for that line and this potential future line that
you want to do. This is also the center bolt and all these need to be done.
You need to do is turn these and a triangle can work for those.
Now, if you're going to use gluons,
what you would do is you would put it in backwards. Hold on.
What happens is you put the rope through, it's pulling on the spine.
Now of course, normal bolts, we just have just the spine. We pull on them.
You add a P the opposite way. It doesn't make it weaker.
It just doesn't get the benefit of the P.
I don't think we need the benefit of the P on this P.
So you put it in backwards.
You can pull 179 degrees without this thing twisting.
As soon as you go past 179 degrees,
the rope would flip over to this side and start twisting on this.
Now, if these things are in a notch, they're not going to twist,
easily at least.
And twisting pops the glue and makes them basically come out. Of course,
we struggle to remove gluon bolts and we can't seem to use twisting as a way to
do it. So not too worried about twisting,
but it is something to consider if you're not notching your gluon bolts.
You don't want to be putting six kilonewtons of force on one bolt because you
don't know how to equalize on something that's not notched.
You do have to understand how that twisting issue can be an issue.
So if I put in, in the same pattern, backwards piece,
then you can have really great gluons that are compatible with multiple lines.
So in summary, think about the master point,
think about the direction of the highline and think about what pattern you want.
And please don't do this right next to the cliff.
If you put these in wrong, you're probably not going to die.
That just means you're an idiot and therefore you shouldn't highline.
Hey, thanks for watching,
but don't be an idiot and try to go bolting your first time out in nature
where it's going to be there forever.
Please at least practice in your backyard or at least somebody else's backyard
before you go out your first time, just anybody's backyard.
And be sure to check out the Bolting Bible.
We're trying to cover all these videos with demonstrations going over all the
content that's in there.
There's tons of rich content that a lot of people help us put together.
And thank you to my patron supporters and people who have helped with this
channel, not just with money, but with their time.
Those who get involved, get access to our entire Slack snap and bolt busters,
break test data and all the videos associated with it.
And you can also help support this channel by getting cool t-shirts or super
good enough hats.
And until you have a chance to put in holes that'll last forever,
please check out our other videos and follow, like, and subscribe,
hit that bell button so you don't miss a single one. Cheers.