You don’t need a drill press or commercial drill guide to drill perpendicular holes. With this simple to make wooden guide, you can use your handheld drill motor and get flawless results!
If you’ve ever put a lot of work into a project, only to have it spoiled or diminished by a crooked or ragged hole, then you’ll love this guide and technique! When you’ve just built a workbench, you don’t want to risk screwing up drilling the dog holes for the bench’s clamping system. No fear of that now!
For many, it is really difficult to correctly sight down the edges of the drill bit to assure that bit is drilling absolutely vertical in relation to the surface. That’s because there are confusing edges and sightlines that compete for your attention. You can now cut through all that visual clutter and use only the shaft of the drill bit, held in a perfect position, to get precise results!
Better yet, the guide is cheap and easy to make, and you can use it with twist, paddle and Forstner bits.
Easy, fast, inexpensive, and most of all effective. What’s not to love? When it comes to setting up for precise drilling, JUST DO IT YOURSELF! (JDIY)
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. If I could show you a way how to drill straight
beautiful holes in even your classiest projects without using a commercial drill guide or a drill
press, would you be interested? I thought so. Stay tuned and I'll show you how it's done.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com. A common task every maker, every woodworker is
going to have is drilling holes in material. Now, if you've done a, let's say, a beautiful project
like a workbench and you're needing to drill holes in it that are straight, perpendicular,
let's say for bench dogs, and you got to get it right, how do you put something like that
in a drill press? No, that's not possible. And how do you, without using a commercial drill guide,
get those holes straight? Well, there's a simple device that I saw recently. Now, I wish I could
say this is my idea, but it's not. I don't remember where I saw it. So, if you're out there
and this is your idea or you know who came up with it, won't you tell us in the comments below
or in the comment section and let us know so I can give credit. But meanwhile, this is the idea.
This is a simple block system using a 45 degree angle off of both edges intersecting the middle
at 90 on just a simple piece of wood. This is about an inch and a quarter thick,
maybe an inch and a half, inch and three quarter wide, eight inches long. And on this end,
you have a V block, which now allows you to put the drill bit straight up and down as you drill.
And on this side, now this is set up vertically. So, let's say you're using a Forstner bit and
you've got the whole body of the Forstner bit and you've already set the drill with its center
spur directly where you need it. Now, you can bring this guide up to it and keep it perpendicular.
All right, as you can see here, I've laid out an intersecting 45 creating a 90 degree corner.
I started in from the edges a little bit to leave a little bit more beef, if you will,
on the corners here to make the tool more durable. So, we're going to saw that out. Now,
on the other end, you'll see I did the same thing, but in the vertical axis where there
is a 45 from both sides, intersecting at 90, leaving the edge beefy, and we're going to cut
this out on the underside. Then we'll put this tool to work and see how it works. All right,
let's get to work. All right, let's go ahead and put it to work. Let's see how this works here.
So, I'm going to go ahead and use just a 3-8 brad point drill. Let's suppose that you were doing a
bench top and you needed some hold downs or some threaded inserts or that sort of thing,
and you wanted to make sure this was absolutely perpendicular, not doing this.
Okay, so what we're going to do is we'll place, first of all, here's the hole right there. I'm
going to just put the tip, place where you want the drill to begin with, then bring the guide
up to it, and then encounter both sides. This stops you from going wonky like this. When you
just bring it, it automatically trues it up, and then go ahead and start and keep holding that,
and you can see it's keeping me very clear. So, let's just put that in there and see what you get
as far as perpendicularity. Look at there. But now when you go to use Forstner type of bits,
there's another problem. If I put this and I encounter, let's suppose that's my starting point
and I'm ready to drill this, and I want to make sure I'm not rocking around. If I use that end
and I put it there, that's going to do no good, right? Where I need to guide is the shaft. So,
what I'm going to do is rotate that around and pull it up to there, and now make sure I'm in
against it, and as you can see, I can go straight down and not have a problem. It's going to be
very vertical, and this is a simple little handheld tool that really cost me nothing with
scrap. I do suggest that you build it out of some kind of hardwood. This happens to be, it looks like
either a cherry or some kind of, I'm pretty sure it's cherry just by the way it burned,
but a kind of a hardwood is going to last a lot longer, and if you'll notice, I rounded over the
edges on it just so it's nice to the touch. It's not sharp, and if you wanted to, you could
certainly varnish this. You could put a hole in it, hang it somewhere. You can customize it and make
it yours. This is a great little tool, makes your life a lot easier, removes the stress, and you end
up with great results. If you have a technique, a tip, a tool like this that you'd like to share
with your fellow viewer family members, won't you do so in the comments below? We'll make sure to
get it out there and give you cred for it. If you found this video to be helpful, won't you like it?
And better yet, please subscribe to our channel, and when you do, ring the bell, because when you do,
you'll get notified whenever a new video episode comes out. Hey, thanks for watching today.
Until the next time, this is Dirt Farmer Jay with DirtFarmerJay.com.