Highlining and Weblocks

HowNOT2
100 followers
3 Video ViewsยทNov 6, 2016
How to use weblocks when highlining, and safety issues to watch out for.
What are the tips and tricks for using web locks on high lines? And what are
safety issues you need to watch out for? Check it out on this episode of How Not to High Line.
Hi, I'm Ryan Jinks, and welcome to my garage. Today we're going to talk about how to use a
web lock upside down, how to get two web locks to play well with each other by offsetting them,
and we're also going to go over safety issues like slippage, how not to lose your finger,
and how to check your balls. If you've only slack-lined in the park,
you're likely to have only used your web locks in this orientation. But as soon as you add a
backup line, you now have to have two web locks on top of each other, one for each line. And since
this is awkward, the main line is usually rigged upside down. So let's go over how to install your
webbing when your main line web lock is upside down. Just like a standard use of a web lock,
the tail comes out of the bottom, and this would be my backup line. But the main line,
if you're going to have your web lock upside down, instead of having your
webbing bent like this, you're going to flip it over upside down, and then you're going to go
around the diverter, and it's going to look like this in your web lock. So now that I'm all done,
I have my main line coming out here and the tail coming out here, just like the picture shows on
the web locks. Make sure that it's still orientated the way it's supposed to be, and you can even
check by holding it right side up. But you take the tail, and it comes off that side. You take
this other web lock, and the main lines come out this way, and your tails come out the top of the
bottom, and they sit quite nicely with each other. Now that we have our two web locks orientated
correctly, it doesn't sit well like this, so my preference is to move the main line back a little
bit and offset them so they're not hitting each other. One option is to use two different length
soft shackles. If you use soft shackles as your main connectors, you can have a short one and a
long one, and then when you put them together, it can shake and bounce around and hit on top of each
other, and if my thumb was the master point, they are offset perfectly. The second option would be
to combine a normal shackle with a long soft shackle, to where if my hand was the master point,
they're still offset from each other, and they're not hitting each other. And your third option,
if you'd like to use normal shackles for both web locks, is to extend the bottom one with a
continuous loop. You can put the continuous loop directly on the web lock or the master point.
In this example, if you put the continuous loop directly on the web lock, it goes through the eye,
you fold it in half, and then you put your shackle through the loops, and it extends it out. So when
you put the two together, you have your two shackles on the master point, and your two web
locks aren't hitting each other. If you want to put the continuous loop on the master point,
you put it on the shackle, you go around your master point, and you put it back on the shackle,
creating a loop, and then this would go on your web lock. The real benefit for putting the
continuous loop on the master point instead of through the eye of the web lock is that you don't
have two shackles competing for space up here. So when you have it all set up, you don't have
anything clashing while the webbing is moving. A fourth option would be to use a soft release setup.
If you have a soft release setup in the system, it puts your main line out further than your backup
line, which is not a big deal, but it does prevent your web locks from crashing into each other,
which is what we're trying to prevent here. It makes for a good option. Warning, webbing can slip,
especially high-tech webbing, and especially when it's loose. It's been a real problem posted on
slack chat lately of people finding their webbings are sliding out from under them as they're
highlining. That's a problem. So you go through the web lock, and instead of just putting your eye
through here, you would go through the diverter one more time, the back of the web lock, then take
your eye and put your pin through that. And that is double wrapped, and that won't slip. Warning,
tie off your tails. You don't know if you installed it backwards in the web lock, if the pin was put
in right, or the webbing can slip. It's always important as a redundant backup to tie off your
tails. To tie off your tail, you take a big bite of webbing, and in this case I'm going to go through
the eye of the web lock 4.0 because it's big, or you can go through the master point. But you're
going to pull this all the way through, and you're going to tie off a mule knot, which is more or less
a overhand knot, but you go around stuff while you do it. Cinch that up, and I like to go around three
times to make sure it's really secure. Two, and three. Then I like to take a carabiner, preferably
locking, and clip this to a master point, a bolt, or something else. Make sure that your webbing still
looks straight, and that you haven't twisted any of these, because you don't want this obstructed
in any way. Now, worst case scenario, if you were to maybe have the pin come out, or it was installed
backwards, or it slips, you're still connected to this beautiful anchor that you've built, and this
web lock. This is not ideal by any stretch of your imagination, but it's better than not being
connected at all. Back up your tails. Warning, your finger is not as strong as this pin. Don't use it
as a temporary pin while you try to feed this eye through to hold it open. You don't know what
could happen with the line, or tension, or wind, or if your partner decides to pull a little slack in
thinking you're done. Instead, it's better to take that eye, flip it over, then set your pin in there,
and then grab it, always keeping your hands open, and making sure you don't have any twists from
flipping it around. But this way, I did not have my finger in there at all while I was inserting it.
Warning, check for twists. Twists can come from high lines being loose, or while you were pulling,
and not being careful to guide it through. You lose a lot of strength when there's a twist
in your webbing. Warning, check your balls. Make sure that you can see these balls after you push
the pin through. I have on numerous occasions come across a high line. After inspecting, I saw
that my web lock pin was only partially through. So when you are done, make sure that you've shoved
it all the way through so you can clearly see your balls. Okay guys, make sure that your webbing is
installed correctly when your web lock's upside down, and that they're offset so they're not
clanging around on each other. Also make sure that you double wrap your webbing so that it doesn't
slip. Make sure there's no twists. Don't use your finger as a temporary pin. After all, you only have
10 of them. And make sure that you shove that pin all the way through so you can easily see those
balls. And in case you fucked all that up, be sure to tie off that tail. Since there's 101 ways to
screw up web locks, therefore, you shouldn't high line.
Hi, I'm Ryan Jinks, and this was another episode of the How Not to High Line series.
This is a guide for slackliners transitioning into highlining. We are not here to spoon feed
the right rigging techniques. Instead, we hope to empower slackliners to critically analyze
any system they're going to use. Risk awareness can keep people alive. Please don't rig your first
highline without an expert. We have too many wonderful and generous people in our highlining
community to go risk your life after watching some YouTube tutorial. Let's keep this sport safe.
And remember, since no system is perfect, therefore, you shouldn't highline. Thanks for watching,
and please subscribe.
