We cut the main line on a 200 meter line! Both a continuous setup AND with an Inov Split highline. Thank you Matthew McMillan, Matt Stolling, Travis Phillips, Levi Lowe, Rob Smith (Slimb soap) for helping with this experiment.
Our results were the following:
Highline was 210 meters long Bag weighs 107lbs or 48kgs Bag was approximately 60 meters away from anchor
CONTINUOUS LINE Anchor went from 2.5kn to about 4kn or 5kn Bag saw 2.5kn of force Bag dropped 18m or 59ft
SLACK INOV SPLIT Anchor went from 2.56kn to 3.15 Bag saw 1.42kn of force Bag dropped 8m or 26ft
All donations go straight back into making this channel better. We put donors names in the ending credits and give them exclusive access to the SlackSnap Raw Data spreadsheet + corresponding footage associated with each break. This all couldn't happen without you!
I'm so ******* nervous. Me too. Ready? Yeah. We're on. What happens when you have a
mainline failure on one continuous highline webbing on a 200 meter highline?
Let's find out on this episode of How Not to Highline. Oh God. God! Oh God!
I almost hit the ******* ground. Hi, I'm Ryan Jinks and welcome to my gear room.
This last weekend we decided to split some enobes to test our new favorite
method of connecting multiple 50 meter sections together called the enobe split.
We do this to try to make long highlines safer because mainline failures can make
you fall a long, long ways down if you just have two continuous pieces as your
main and your backup. So about an hour and a half from where I live here in
Loda, California is CRG, Cosumnes River Gorge, and we rigged the 200 meter line,
that classic line that was the world record a few years ago that Jerry
Meschewski did. The easiest way we found to tag that line because of all the
trees, the rivers, and the steepness is with a drone. And we had 300 meters of
Dyneema fishing line on our super big trolling reel. I had 200 pound test
fishing line on our reel and I found that to be too much because it's 0.75
millimeters in diameter. Next time I'll go with either a 75 or 100 pound test
fishing line that is also Dyneema so I can get more fishing line on the reel
and that it's not so thick when you're trying to work with it. And with the
river so high, Rob Smith and Matthew McMillan hiked in from the bridge since
we couldn't cross this time of year. That is so stressful to fly a drone. There's no wind
and our fishing line was like curved at a full side sag and we had to keep it
out of the trees because the trees here are pretty close to us here. But we're
about to pull over the six mil tagline. They had the tagline with them and so we
the drone to them to reel in the tagline. Once we got the tagline across, then we
can send them over the webbing which we had with us. And in order to send over
webbing that is as heavy as a 200 meter line, we had a redirect or a Z-drag in
order to not have to hold the entire weight. And then we had Levi keeping it
off of the edge so we had no abrasion.
3-2-1. 3-2-1. This is a 3-2-1. That's so stupid. 3-2-1. It is a 3-2-1. See?
Promo for Snatch. Snatch is awesome. 3-2-1. I think that's enough. Yeah, that's enough.
So I'm at the static side of the 200-ish meter line at CRG, Consumus River Gorge.
And we built our anchor here with a piece of short webbing that had a sew-and-loop
on it from my slack snap stuff. And so I could cut this and not my actual piece
even though it'll probably get compromised when it falls down there. We
have fiber reinforced tape as our tape. We'll see what happens with that. The
dyno and the soft release are on the backup, which is counterintuitive when
you rig. But we put a lot of thought into this. This is on peak. There's one on the
other side. And the bag has a dynamometer as well. The backup here is spider silk.
Very, very low stretch. And it's got a very normal amount of sag that we would
have when we highline. So we're curious how much just static shock it's gonna
put on our anchors and our bag to find out if we would get seriously injured.
Now our other biggest concern is abrasion because that far side has
nothing but three things for it to hit. Nothing but abrasion for 40 freaking feet
because the anchor's at a tree far back on the cliff. And that's always been a
joke that if the mainline failed on this line you would die anyways. But I
really want to know if the enub split, where it's 50 meter sections all
interconnected, would make this line a lot safer because if the mainline fails
it's only a little bit of the line. You don't drop as far and the rest of the
highline is absorbing your fall even if you are using a static backup. I've spent
like three or four months planning this moment. I'm so excited and I really hope
this doesn't like throw me backwards. I'm so curious. I ******* love science.
Oh it almost hit the ******* ground. Oh no. Oh no. Dino's on? No. Oh it didn't read on peak.
Fuck ours did too. Son of a bitch. Is the webbing rubbing the rock over there?
Oh we can't publish these results then because it didn't go bad. God damn it.
This has been safe the whole time and I thought I was a badass. It dropped 18
meters. What's that in English? Close to 60. Just your standard rope swing. The only
rock it actually touched which surprised everybody here was this rock right here
which was well padded. We padded the other ones down there with sidewinders
you can see. They're sending a new line across. We padded this with sidewinders
down there but it didn't touch those rocks and it didn't touch that final
edge down there either. Even though the bag fell about 18 meters. Just like
everything we ever do on this channel it's all super good enough. We're gonna
now rig the Enov split and do the same experiment which would be super super good
enough. That almost cut before my ******* line did. That took a lot more cutting
than I thought it was going to. So we got the tagline over here when we slid over
so we can pull the Enov split over and rescue our bag. We're gonna pull the
back up tight so it pulls it higher and then we're not gonna rig this
highline very tight so they match and then I can pull the rocks out and we can
put more rocks in later. So we just set up the Enov split line. We just pulled it
across. I put another connector here with a sewing loop so I don't have to cut my
actual piece and our soft release is on the backup. This dynamometer is
embedded in here I can't put it in this right now but this because only this
section is gonna fail I'm gonna put this rope as the backup because this will be
the new main after we cut this. So this experiments already set up I got to take
that bag off get the reading off of the dyno and well enjoy the highline for a
bit before we cut it. So I tried to pull the rocks out of the bag but what
happened was as I pulled the rock up I was getting heavier and the bag was
getting lighter so I couldn't ever get my arm out of the bag even if I could
get a good grip on those big rocks. What I did is I had the loop put directly on
the Kootenai carriage and then I basically wound it up two times under
the bag and I pulled up which is in that position when you're hanging a
little bit easier to pull down with one hand and up with the other and I got all
the weight onto the Kootenai carriage onto the soft release. So now the weight
was completely off the ring and I was able to basically put my legs in the bag
and pull it close to the anchor until they could throw me a rope and help
assist me the rest of the way. Okay so we're gonna cut the ENO split line that
we have rigged right now that Matt McMillan is sliding across. Since I
learned I cannot pull rocks out of haul bags because it makes the bag lighter
therefore the bag keeps going up as I lift we've already set our rescue system
up before we cut the mainline. This is going to go a lot smoother because as
soon as we're done the ENO split will only allow it to fall I'm estimating 10
to 15 feet and then we'll just pull the bag back and de-rig. We'll have to
measure to make sure the main is correct and the backups correct and then if that
is then it's the pink tube and the stretcher webbings have to have longer
backups.
From this spot is negative six meters and we'll see how many meters it drops
after he cuts it. Okay we're at 2.56 kilonewtons standing tension on the ENO
split line before we cut it. Hey guys I just want to say hanging out with Brian
is ******* fun.
Okay so it's negative 14 meters below the same spot that is 8 meters of a
drop. Last time it was 18 meters and this time it was 8 meters. I think it's on the
other side of the ENO split. I got to go rescue the bag now. So we pulled off the
bag it jumped over the ENO split connection which is kind of a bulgy bump
because of the soft the soft shackle button knot. Soft shackle button knot was
inside it's one and a quarter inch bump. Anyways to jump the thing with with
these guys helping I was able to lift the Kootenai carriage over it came over
just fine and it had 1.42 kilonewtons on the bag the force it saw which is
less than half of what our other test was and it fell less than half the
distance of our other test. So there's pros and cons of both systems but I sure
feel better about this one. Hey guys so we got home late last night everything's
flaked out and we're gonna go over all the splits and what happened to them
after the backup test. This is the webbing we cut obviously not an ENO split
this is just to connect two main lines so that we only had to cut a very short
section of webbing and not waste a 50 meter section of webbing. If you slow down
the video you can actually see when I cut it here I didn't move the knife way
quick enough or something and the leash bounced up from the recoil of everything
and went right into the knife and actually cut about halfway through the
leash. Okay so let's look at the next connection now. This is the main line
still and this is the backup and this is where the backup connects to the sling.
You can see that everything stayed in place there the padding is on the
padding the tape really didn't move everything's good there. Just so you know
when Ryan has slack snapped this setup with the girth hitch as long as they're
both padded that way they've come out to show pretty much full strength of
those slings. So going on to the next connection this is the main line and
this is where that backup sling I showed you meets the other connection and what
happened here you can see is the the red sling is the figure eight one that goes
through the two mains and that got cinched down between the backup of
this and the main here so that cinched that down around everything and it
didn't change anything. The connections there you can see some residue from the
tape you can see that it loaded but there's no damage to anything that we
can see so far. Okay so we're at the next connection and you may have noticed as I
was going along there's some different webbings for the main line. Now the main
line is going back from pink tube to Feather Pro that's because we did the
Franken line webbing thing and we put Feather Pro as the main throughout the
entire line except for one section in the middle was a 50 meter section of
pink tube. The backup was all 50 meter sections of spider silk and then those
were connected to five meter Dyneema extenders. So we got an unexpected result
by doing this Franken webbing technique. When we looked at the line after it was
rigged the pink tube didn't have any backup loops underneath it. The Dyneema
sling and all of the backup composed of the spider silk was tight up against the
main line or almost tight and when you slid on the line they were both pretty
tight. Our theory is that either the pink tube was taking most of the stretch
of the 200 meter line or pink tube just stretches that much more and you have
to use longer extenders. In any case we'll take apart
this connection and take a look at it to see if anything is shifted in the
split from the experience of the pink tube stretching out and loading the backup.
Oh my god. You haven't solved anything. It's still wrapped around it. I know, but I can at least show it in the video. I'll take care of that later. You're not supposed to show them that part.
Everything on YouTube is supposed to look easier than it really is. That red tape is
to help the ring slide over all this stuff and the white tapes to keep it in
place and then each individual soft shackle has tape to keep them closed but
that button knots not supposed to be outside of that loop. Yes, so you probably
could see that before I untaped it that this button knot had shifted out of the
loop that it was stored in originally which was this loop. Which is no it's
the red button knot goes inside of this loop. Which that did stay. Yeah, that one
stayed. But this being pulled sideways I think. This one being loaded pulled the
knot out of here. Which shouldn't happen if you have an extender that's long
enough. It'll stay in there. But everything seems fine. It's just kind of obnoxious
to try to walk over. Mm-hmm. You're not gonna walk on a line that has a backup
tighter than the main. And when you rolled over you kind of had to just pick
it up over it but yeah. The experience of rolling over the slack knot split was
really pretty easy. It was not as difficult as I anticipated. The buttons
on these can I guess cause a little bit of an issue when you're rolling over
them with your hangover. You don't have to unclip or anything but sometimes you
just have to fiddle your hangover over the top of it. We've been discussing
using smaller soft shackles. These are six millimeter soft shackles. A five
millimeter soft shackle is gonna have a 25% smaller head button. And the breaking
strength is plenty. This one is way overkill. Ryan slacks... I can't say the
******* word. Ryan slack snapped these. Whoa is that... that's just the tape pulled off
of itself funny. That's gonna come off just fine. Yeah. But we taped it here to
make sure it didn't open and we taped it here in two different places to make
sure it didn't open. So that's how we just... I mean they're not jiggling but
people are concerned about that. Yeah the tape didn't move. What happened was the...
the other soft shackle rubbed against it. Cinched down on top of it. Yeah. And
squeezed the... yeah. And then this this am steel on that am steel doesn't really
show any abrasion. So that feels... In fact you don't see any abrasion on any of the
soft shackles or on the sewn loops. Yeah. Everything seems pretty... pretty good.
Especially... I mean that was a full... a full cut and everything. Did you get red on there?
There's some red. Oh there's some red dye. Yeah. But that happens when you just handle
them. Yeah. I've noticed that on anchor points with soft shackles you'll see the
blue dye. Awesome. So yeah that slack and all split turned out good. There you see
the main and the back... or the main and the main. The backup and the backup. Everything's still in place.
It's ready to go again. You could use it again. So this experiment was super
enlightening on what happens with a 200 meter line. The 200 meter continuous was
an 18 meter or 59 foot drop. The bag saw 2.5 kilonewtons and the anchor we're
estimating was 2.5 when it started because it was the same as the enobe.
And just from lots of experience with stuff it definitely did not go above
4 or 5 kilonewtons which is perfectly safe for the anchor. Now 2.5
kilonewtons on a bag that weighs 107 pounds or 48 kilograms would be a little
bit higher if you were 160 pounds or even 200. If you saw 5 kilonewtons on
your leash, I'm not worried about your leash. I'm more worried about your back.
Now all this is for just a 200 meter. If we rigged the 300 meter that's also
there, our results would have been significantly bigger, longer, and higher
forces. Now with the enobe split, regardless of how long it is, the results
would pretty much be the same as we got here. It was only an 8 meter drop, 26 feet,
or 1.4 kilonewtons on the bag and even doubled would not hurt you. The anchor
for the enobe split started at 2.56 kilonewtons and only went up to 3.15.
That's not even a full kilonewton difference because the stretchy main
line helped absorb a lot of the fall instead of everything falling on a
static backup. Now even if you only fall about 30 feet down, if you land straight
on the line or hit your leg or something gets caught or you're doing flipper
whippers while taking literally a rope swing, you could get hurt and you could
even get hurt more if it was a 2, 3, 400 meter long single continuous piece of
webbing. Now there are multiple ways to skin the cat on how to connect multiple
high lines together and some people debate whether or not it should be 50, 60
meters, or 100 meters long at each connection point. And obviously I like
the 50 meter method now because of the results but also the even number that it
is 60 meters is just a little too odd and a hundred meters to me is just too
long. Either way, continuous lines are still gonna probably be used and be
risky and enobe split connections do take a little thinking in order to put
them together. Therefore you shouldn't do any highlining.
Hey thanks for watching but don't be an idiot and try to go highlining on any
size line by yourself the first time you go out. Please go with someone who knows
what they're doing the first time you try this. Go to slackademics.com in
order to find the 1,300 Facebook groups that we have sorted based on area so you
can find a slackliner near you. There's also a ton of festivals that you can
attend to network and see how things are rigged properly and get immersed into
our community. And I also offer private lessons in case you're interested in
learning one-on-one so private message me if you're interested in that. And
thank you to those who help support this channel whether it's patron $1 per
episode or just a one-time donation on PayPal. You can also buy a t-shirt on the
link in the description below. The people who do get involved now get access
exclusive access to our slack snap data. We just passed number 430 on slack snap
and we have all the videos correlated with that chart that you can have access
to all of that if you get involved. Until you have a chance to go cut a large
hairline you spent all day rigging, make sure you like, follow, and subscribe to
catch all of our episodes that we have coming out. Cheers!