
The Kelley's Country Life
18 followers
All right, welcome back everybody. I recently just released what wound up being one of my most
controversial videos ever. I was a bit surprised. I knew I was going to get some feedback on what
I'm doing to my equipment, but not the way that it did. It wound up being the most views I've ever
gotten in 24 hours, the most thumbs down, and probably the most comments, and they're still
rolling in day after day. Although I will say the majority of the comments were constructive
criticism. People want me to protect my equipment, so I have listened. I've listened a lot, and I'll
be honest with you. I've read so many comments to the point that I got very confused on how I wanted
to move forward with speeding up my splitter cycle time. So if you're just now catching this video and
didn't get to watch the last one, I'm going to show you exactly what I've done, why I've done it,
and why I'm going to remove it and going to go after a different option. So let me fire this
splitter up and warm it up here for a second, and I'll show you that this bar, this piece of metal
that I put in right here, shortened my stroke up, shortened my split length up, so it sped my cycle
time up. I no longer have to wait on this splitting head to retract all the way back into the cylinder
and come back out. I'll also try to remember to include that last video of me doing this at the
end of this one if you want to watch and see the difference, and I'll show you exactly what I'm
accomplishing right now with this bar, how it kicks this splitter out again here and not going
all the way in. All right, so as you can see, when this splitting wedge hits this, it's actually
kicking out the little indent that's holding this in. So the big concern with everybody and one of
mine that I expressed in that last video was this pivot point right here. This is eventually going
to wear out the hole that's going through the cylinder shaft, and that could be a costly repair.
There's also some pivot to this since the bars are up so high, and it's actually pushing
pressure up underneath the beam here. So a lot of concerns from viewers. Y'all had a tremendous
amount of ideas from putting bars on the side, spreading out the pressure, changing pressure
settings on the detent, putting collars on the shaft. I mean, a ton of ideas. Y'all really did.
However, every time I thought I was going to mess with one of those ideas, somebody would come along
and show me either a video of somebody having collar slip on the shaft and busting this off,
or talking about not messing the pressure relief valve on there because there's only one,
and changing the detent pressure setting, may change the splitter pressure setting, etc. It
got to the point where I got so scatterbrained, I said to heck with it. So today, I am going to
try to figure out how to make a return mechanism so whenever this bumps it, it will actually kick
the handle out so there's no pressure, no pivot points, no nothing. I think I have bought enough
stuff from my local hardware store that I can rig something up here. I've got a welder, I've got the
tools, but that's what we're going to do today. We're going to do no pressure, no hunks of steel,
no nothing. We're simply going to have something kick the handle out. That's the safest thing that
I can think of to protect my equipment and eliminate these pivot points and wearing things
out early. So I'm going to look around for a few minutes. I may alter the design that I have in
mind. We're going to see what we can come up with.
All right, so all I did was cut a piece of rebar here. I've got a steep angle on one side where
I'm going to take a piece of pipe, actually weld to it to make a pivot point. In the bottom, I'm
just going to weld right to here. It should not be in the way, even if I were to ever let this fully
retract. But what I'm trying to do is weld that pipe on and something pretty rigid to the frame
right here to, like I said, make a pretty good pivot point. I think this will work for what
I'm trying to accomplish right here. I need to grind some paint off so I can get ready to weld
that up. All right, so I didn't have the camera rolling, but all I did was just tack that piece
of pipe onto this piece of rebar. All right, this seems to work well, but I already see a problem.
So when I push that back, it locks and say if the splitter head was coming back. I've got this
adjusted, by the way, to just touch this. If it were to come back another fraction of an inch,
I'm barely going to push on this. It kicks the handle right out. Problem is this can now pivot
all the way over here out of the way or all the way to this side out of the way if this was full.
So then that would allow this to run all the way back and bind my bolt up. So a quick little fix
that I can think of is take a spring, put around this. I'm going to shoot a screw in down here that
I can hook this on because I want to make this removable and that should put just enough tension
on this to probably keep it pulled over like that. However, whenever I push back on the handle,
it automatically centers it up. So let's see if I can make that work out.
I don't know about y'all, but I call that an absolute success. I am very pleased with that.
I'll just have to watch it as time goes on. I am curious if eventually after hundreds and
hundreds of strokes, if this shaft could bend. But now that I got spring tension on it,
I don't know that it will. I could always just add one more piece of rebar weld to it,
really strengthen it up. Everything else I think is going to work just fine. As long as this spring
doesn't pop off and this kick over and it retracts and bends it all up. That's the only concern that
I have, but that's a heavy duty spring. I have a pretty decent size screw in with a big lip,
so the spring shouldn't pop off. That's the only thing to really watch.
Now here's the cool part about this design. Right now I have it set up
where it's exactly where it was before, 17 and three quarters of an inch. That way, if I have
16, 16 and a half inch pieces of wood, I can drop it right in there. It's ready to go. But I designed
this specifically to be adjustable. All I have to do is loosen these two nuts and I can screw this
all thread all the way back in and change my length of opening. So if I want to go up to 18 inch pieces
of wood, which I'm really considering doing, all I gotta do is screw this in another inch and a half,
two inches, and it'll open this up. The trigger mechanism worked the same way. Now there's also
one more thing that I've done to make this really, really easy and convenient. Let me show you.
All right, so say for some reason I want to split big 24 inch pieces of wood, or I want to throw
one or two big pieces in. Instead of adjusting this bolt all the way out, I tried to make this
thing where it's easily removable. Literally just pop the spring off. This comes up out of a pivot
point. It's completely out of your way. This thing is ready to go now. So you can run it just like
normal. This piece that's welded on is absolutely not in the way, will not affect nothing. Now the
splitter's back to normal that quick in a matter of a couple seconds. All right, now it's just as
simple to put back on. Just slide it back down to that pivot point, put some spring tension back on
it, and it's back to normal operation. I think I'm going to really enjoy this. All right, I'm just
going to split some pieces real quick. No, I'm not even set up for a rack, a tote, nothing.
Demonstration purposes only. And then behind me back there, we're going to crank up the saw for
the next video, do a bunch of big cutting, and we'll really put this splitter to work. But right now,
I'm just going to throw a few splits over that way as I split them, and let's test this out.
All right. Well, I don't mean to brag, but I'm dang proud of this design. It's ugly, no doubt. Doesn't
look factory or professional, and I think it's going to get the job done. I love how quick and easy
I can take it off. As you just seen, I had a piece that was just a little too long, literally two
seconds. It's off the machine. I can split the piece. It's right back on in two more seconds.
That's something that was very important to me to build something that would be quick.
I have noticed a couple times whenever I push back, sometimes the handle will come forward like
that. I either got a little bit too much spring tension or the easiest fix to that, this all
thread right here, I'll just bend it back maybe a quarter of an inch, so it's putting slightly less
pressure on this handle right here. That, or I can stretch the spring out, but it only did that a
couple of times. That's just a couple of little bugs to work out, but it works, and it works really
well. I'm very, very happy with that design. Now that I think it's going to work, I'll take
it back off a little bit later, paint everything up to try to stop some rust, and we'll really
give it a workout, really test it. Like I said, I'll make a few minor tweaks to spring tension,
a couple other things, just to kind of get it where I want. Now this was not a how-to video. I
don't make those. Our channel is strictly about showing y'all what we're doing around our place
right here. So if this is a design you want to try, I think it's extremely safe. It doesn't create new
pinch points like the bar did. It doesn't put any pressure on the machine, none whatsoever. It's
operating a handle that's already designed to operate it. Now yes, it does kind of require a
unless you can figure out how to bolt that one piece on. Other than that, I have a $4 piece of
all-thread here, a couple nuts, a spring that I already had laying around, and a piece of scrap
rebar. I mean, I have literally $5 in this design, so very happy with it. Not much time to make it,
and I love that it's fully adjustable too. So like I said, if I change my mind in the future and want
to go to a longer firewood length, it's as simple as loosening two bolts, screwing this all-thread
through a little more, tightening the bolts back down, measuring my distance, and I can go to town.
So really, really happy with it. I'm sure as often is the case, I'll still wind up getting
some criticism. Hey, so goes life and putting your life out there on the internet. But hopefully y'all
find this design a whole lot more fitting to the machine versus the pressure that I was putting
before. And I 100% agreed with y'all. Luckily I didn't run it long like that, but eventually I
was going to wear out the shaft, break a bolt, cause some extra stress on the machine that wasn't
necessary. This design completely eliminates all that, and I appreciate all the suggestions that
y'all gave me. Sorry I didn't really go with them. Once I got this design stuck in my head, I was
dead set that I had to do it. So thank y'all so much for watching. Hopefully you enjoyed it, and we'll
catch you on the next video.
