In this video Alex walks you through the pros and cons to having a skid plate on your canoe. He then walks you through a full step-by-step guide to installing a skid plate on your canoe. A simple way to protect and add durability to your canoe.
What's going on guys, it's Alex here with Northern Scavenger and today
I'm going to be showing you how to add a skid plate to your canoe.
So before we dive in, some of you might be wondering why would you add a skid plate to
your canoe. I know that there's a number of people that wouldn't add a skid plate to a
brand new canoe. They might wait for the canoe to get a little bit beaten up first and actually
have them start worrying about the overall strength of the canoe. And I know that there's
some people that don't think that they're very good looking. I kind of disagree. I like the,
I like the look of a skid plate on a canoe. I think that there's something, there's a classic
look to that. And finally, there is a little bit of extra weight when adding skid plates. So maybe
an extra pound or two that you'd be adding to your boat in the grand scheme of things. For me,
it's worth the extra durability of adding one of these. And I also wanted to test this out. So
we've used, this is a brand new, a skiff canyon canoe. We've used these before without skid plates
and we've beaten them up and they've been absolutely fine. This time, I just wanted to try
as an experiment to add some skid plates to see what the extra durability does. Does it affect
the feel of the boat at all? Do I feel like this is actually adding some good protection to the
boat? And is it worth putting on right away? And so that is why I decided to add it. And I just,
I did want to add like a little extra protection for the canoe because we do beat the heck out of
these things on our trips. And so having that skid plate is just going to be a little extra
peace of mind for me when I'm out on the water. So the first step was to make sure I was working
with a clean surface. I placed the Kevlar skid plate down in order to figure out exactly where
I wanted to place it. You want to have the skid plate start about nine to 10 inches from the tip
of the canoe. And you also want to ensure it is lined up with the center of the canoe before
taping it into place. Once it's held in a secure place, it's time to tape around the outside of
the skid plate. I tried my best to keep about half an inch around the outside of the patch
so that the epoxy could create a seal around the outside edge of the skid plate. This also
makes for a nice clean finish when you remove the tape at the end. I used a few different techniques
to do the rounded corners with some smaller pieces or just trying to use one large piece
and pushing it into place. Either way, I ended up taking a knife to clean up the corners.
Once I had the tape in place, I removed the material so I could start sanding.
Trust me when I say it wasn't easy to do this to a brand new canoe. This hurts to do this to
a brand new canoe. The reason we sand is so the epoxy has a rougher surface to cling onto
for a stronger bond. The more you can rough this up, the better the epoxy will hold.
Once the entire area was sanded, I used a cloth with a little bit of isopropyl alcohol
to clean the surface of any oils and any dirt that might be left.
Now adding the epoxy can be a messy process with a lot of dripping. I ended up taping garbage bags
to the perimeter to ensure that I wouldn't have any drips along the side of my shiny new canoe.
Once the whole area was protected, it was time to mix the epoxy resin.
It's recommended that you wear gloves, eye protection, and even a mask when working with
epoxy. Eskif sent me some epoxy with the skid plates for me to use. I ended up using solo cups
so that I could equally divide the epoxy between the bow and the stern of the canoe.
The mistake I made here was mixing both the part A and part B of the epoxy
for both ends of the canoe in the beginning. So by the time I had finished working on the
first skid plate, the epoxy had almost hardened for the second side. I actually ended up starting
to apply it before I realized that it was starting to harden, and this required me to
have to go back and chip it all off and sand down the surface again. Complete nightmare.
So don't do that. When applying the epoxy, you want to work as quickly as possible. I started by
applying a thick layer to the boat before placing the patch on top. This helped ensure that there
was a good base of epoxy under the patch before I placed it down. I know other people that use
larger buckets and actually dunk the entire patch into the epoxy before applying it to the boat.
I think either method works. Once the patch is placed down, you want to try to soak it with
epoxy. I tried to get as much of the resin in there as possible and sometimes used my gloves
to help work it all in. The areas I had soaked the best ended up being more red than the yellow
and white spots that you can see. I think these spots may have benefited from a little bit more.
Once I was done the first side, it was time for the second. After I cleaned up the mess I had made
from the hardened epoxy, it was time to get started. The other downside to my mistake was
that I had to go out and buy more epoxy, and it isn't a cheap product. The new epoxy did come
with some schnazzy measuring cups to ensure I was getting the right mix of epoxy. This was much
easier to work with than the solo cups. The second skid plate seemed to have received a much better
coat of epoxy. I think this was both because I had more epoxy to work with and also I had more
experience at this point. The final step is to remove the tape. You want to wait until the epoxy is tacky
to the touch, not completely dry but also not dripping anymore. Once you remove the tape, it
will leave the perfect clean edge along the outside of your skid plate. All in, this process was not
overly difficult and I hope this video helps you if you want to add a skid plate to your canoe.
I've used mine for a full season at this point and they are both still very much intact and I
haven't had to do any repairs. I also have not noticed any significant change in the weight or
maneuverability of the canoe in the water. So all in all I would say a success with the skid plates
and I think I would install them on my future canoes as well. Happy paddling!