Building the Bouchie Dory - Part 35 - Installing Thwarts

Nomad Boatbuilding
98 followers
1 Video View·Jan 23, 2022
My website: https://www.nomadboatbuilding.com
Instagram: https://www.instagram.com/nomadboatbuilding/
It's not about the money but living isn't free...
Buy some merch: https://www.nomadboatbuilding.com/shop/
Support these videos with monthly or annual pledges at Patreon: https://www.patreon.com/nomadboatbuilding
Or make a one time donation: https://www.paypal.com/paypalme/nomadboatbuilding
I'm Mark Rutten, welcome back to Nomad Boatbuilding. In the last episode of
building the Bushidori we got the full pins in and that means I'm anxious to
get out there and try them. But there's one thing that's thwarting
my efforts to do that and that is something to park my keister on
and that's thwarts. So today we're going to install thwarts and I'm about to show
you a method I'm using for what we would
call spiling. This is more pattern making
and more to the point this is actually more like mocking up the thwarts.
This is not the most efficient way to make a pattern
to make the thwarts. I want you to know that right off the bat.
But it's the way that I sometimes do it and sometimes it's just
I don't know. I don't know why I do it this way. I just feel like doing it this
way. We still get the job done so sit back
and relax and let's get right into it. To spile for
the thwarts we need a couple of sticks that come across here to support our
spiling. So here's a quick way to sort of size
those. I just take a couple of sticks that are shorter than the width of the
boat and just overlap them like so until I
got sort of a rough width and I can take that and I can lay it on
some stock like so. Cut it to length and fit it in
there. Now these don't need to touch. They can
be sloppy. We just need to fit them within the
general space. So I'll do the same thing back here. So I'm going to come back
about eight inches because that's the width of
my thwart and make another one.
Just cut that off there. Really simple. All right now I've made up a piece of
stock that equals the height of my thwart
including a piece of doorskin. There's nothing special about this little leg
here other than this just helps to stabilize this thing on the
thwart riser. And so I'm going to get some doorskin now and what I really need
to do is fit the doorskin in around this frame
and up to the planking. All right I'm just going to work with
some little pieces of doorskin here. I want to nestle them up against the
planking and the face of that frame and make sure that
this stays put. Very important.
And then I can use a little scrap here to just
find the edge of that there. There we go. Now there's a little
a little whisper of a gap on one side so I'll just give myself a marked
indicate that. Of course we're going to be working
with the edge of this material here so I don't have to worry about
whatever's sticking out past that. So we'll do the same thing on the other
side. Okay now before we move on we need to
make sure we take a bevel and we can take a bevel off the
planking or off the face of this frame here.
Depends on what you have room for. I'll just go for the frame I think.
These don't have to match exactly even in fact a little bit of space on the
back side isn't a terrible thing. So there's my bevel.
If you compare it to the planking it won't be exactly the same. It'll be close
enough. And so that we don't lose that a really
good practice is to take that bevel and if you have a square edge
on any of your stock just mark it on there like so
just to indicate what that was. All right now here's my pattern.
Here's the stock I want to make it out of. So basically my pattern's got to fit
on here like this. So what I think I might do is I think I'm
going to work from the back side and I'll start by cutting these
square and then I worry about the bevels
afterwards. So we'll flip this over.
I'll just lay these up here like this. Make sure I get away from any smite that
I have on that plank. Of course you want to remind yourself
if you have any areas that aren't a perfect fit this is
the time to make sure you've marked those on the
other side of your pattern. So we'll start by cutting those out
square and then we'll go back and we'll worry about bevels as a second
operation. I always feel like that's the smarter way to go on this sort of thing.
Before I go and cut this out I want to sweeten up this line a little bit.
Those pieces of doorskin I used had square edges
and this line is not naturally square in the boat. It's got a curve to it so I'm
just going to grab a section of my of my sweep here and we're just going to
tweak a little bit of shape into it just to make it look a little bit nicer.
That's going to look a whole lot better. All right so that method
is not super efficient because you're working from the back side and
transferring stuff around and all that sort of thing.
The normal method of doing this would be
a regular spiling process. So you would use
some doorskin or a plank or something that would span across
and rest on those thwart risers. And then you would have a spiling block
which is a little block parallel sided with a bevel on one edge.
And the idea being that the combination of the thickness of
both this piece of material here this doorskin or whatever it is
and the block equal the thickness of your thwarts.
So they're mimicking that thwart and this edge is going to touch wherever the
top edge of your thwart will touch. So you
would put this on the thwart riser, you would run this guy up against the
planking or the frame and then you would draw a line onto the
doorskin along the back side of this and then
once you have finished marking all this out you
drop this down onto your thwart material, take your block,
flip it over, line it up with those pencil lines and then transfer this
line down with your pencil over here onto your thwart material.
Why don't I do it that way? I have no idea.
I should. I should be doing it that way. It could just be that I don't often
have like really nice doorskin material on
hand that will span the distance without it just being super saggy.
And doorskins gotten junkier and junkier. It's like a
like a potato chip these days. And if I'm already
working on something in the shop and I need to bring in a full sheet of
material, there's a boat in the way, running a
full sheet of anything through the table saw is almost impossible because there's
just not enough room in the workshop to do that. So I find
workarounds are not always efficient workarounds.
All right let's get back to work. All right now I need to deal with those
bevels and the best way to do that is to really figure out what the offset of
your bevel is. So if you take a piece of your
scrap stock here and just lay that bevel off
across one side. And then take a square. Square across one end of that. And now
what you want to do is you just want to measure the distance of the open side of
that that angle there. And that's your offset
distance. So in my case that angle is just shy of
three quarters of an inch. So now I just need to take my stock
and basically this is the back side. Take the end of that cut I've created
and lay it off that distance back here. Just carry that line back. Now cutting
this out is really just a chisel operation.
You can start with a rip saw by hand to rip down and then chisel out
the remaining material. We can cut these off on the band
saw at the right angle but we can't do that with the frame notch.
I'll hold back from your line a little ways.
Okay I'm going to switch to a paring chisel to finish this off.
There we go. That should do it. I have a little cleanup on the sides to take care
of. I'll do that with another paring chisel.
Okay we take a little bit of going back and forth before you finally get the fit
right. But eventually you'll get it. It's a
good idea if you can have this thwart sort of bearing against the frame
because it is supposed to help to keep the boat from
coming and going in terms of the beam. Now we need to fasten it down
and what you want to do is you want to find the spot that has the most
meat in your riser. Now if I come too far forward
my fastener is going to be exposed on the inside which we don't want.
Come too far back we don't have any meat. So I'm going to go with
basically right on the edge here. I'll just bring that up lightly
on both sides. I'm doing this now because after I've drilled some holes I can do
the sanding on the surface here. If I slip a little bit when I'm messing
around with drilling these holes I don't have to worry about it so much.
I'm going to use my ship's curve here to draw a line.
This is going to help to compensate for the fact that my thwart riser is curved.
I'll just give it a slightly greater curve here and all I really want to do
is I'm just trying to mark a couple of holes.
So there we go. Now you want to come inboard
enough that you're not too close to the edge
in terms of these fasteners having some strength.
There's enough thwart here. I could probably get away with three fasteners
although I won't do that because I have screws down the middle
and I think four would be rather excessive. So we're just going to go with
two and I think I'm going to bring them in
from the edge. Probably about one and a quarter inches
looks about right to me. Now we'll go a little heavier, one and a
half inches in.
We still need to bore out these holes for the clearance of the screw
so the shoulder of the screw needs to be able to slide easily through those holes.
I'm going to open them up using a tapered countersink here first
and that's because this tapered bit will follow that hole really nicely
but then I'm going to follow it up with a larger bit, just a straight bit
and that's going to be just ever so slightly larger than the actual shank of
the screw. I want just a little bit of movement
around those fasteners that's going to give this
plank a little bit of room to expand and contract.
I also want to countersink this hole ever so slightly so that
when I use the straight bit it doesn't splinter out the edges.
I'm going to do both sides first. Now I want to use the straight bit.
It lands within the confines of that countersink and it won't tear out the
surface grain. All right we've got the thwarts all
fitted now. The next thing we need to do is sort of sweeten them up because right
now they look kind of big and chunky and the way we do that is by relieving
the bottom. So right now we're seeing the full
thickness. What I'll do is I'm going to trim away
this corner so that I have about maybe a third of the thickness left here.
I'll taper that out towards the thwart riser so you just see this nice gentle
arc. It's a shadow line. We'll bring it back about an inch on the
bottom. My first step from finishing these off
is I'm just going to mark where they touch the
thwart risers. So next I'm going to mark my depth.
I'm going to be basically putting a bevel on this that's tapered towards the
ends. So I'm going to come down about a good
strong third maybe a bit even lower than that
because I can also put a chamfer on the upper edge. I don't want this to look too
thin. This is just slightly over half. Now I'm
not really worrying about where center is.
I could mark center. I'll find it just by eyeballing it like so.
Let's do this. Flip that over so center is approximately right there.
I'm going to use my ship sweep and I'm just going to drag it out.
I bring my height right to here. Drag out the sweep. Maybe I'll take the
tip of it I think judging by the length of the sweep.
Touch it to my mark and to my depth. It's a bit hard to hold that on here.
Come on.
Flip that over just holding the tip of it on my
riser mark. There we go. So that's a nice gentle arc.
Mostly we worry about doing this by eye ultimately.
So I'm not too worried about the pencil line.
It's really just a guide. So that's the first one.
Now on the back side what we want to do is a similar thing.
So I'll just mark where this curve ends and then right here the midship point.
I'm going to come back about an inch. A strong inch and likewise I'll use the
same sweep. I can even use the same curve if I like.
Rotating only as I try and draw.
This can stop at one end or it doesn't. This way. That's better.
Now while I've got it in this orientation I'll just do the other side
as well. This clamp is providing my depth
for this sweep so I don't even have to worry about marking it.
It's not even something I've ever done before actually.
Here's hoping I can remember to do it next time I got to do one of these.
All right back around. Now you've got to be really careful when you're
playing with these torts. It's easy to go and bash the face up on something.
So again I'm going to eyeball depth right about there.
Center.
Okay just get down low and have a little sight along there. Make sure that
everything looks good. There's a little slight dip in the middle
there which is not unexpected. I like to use a draw knife for roughing
this out. Now this can get difficult to do because
of the steepness of this angle but we'll do what we can.
You've got to be really careful that you don't go and create tear out.
So I'll just start here. You can see how this is starting to run really badly
right there. So just gradually work my way down.
Now resist the urge to just grab those and peel those off. You don't want to do
that. As you're getting closer and closer to
the line you got to be really careful you don't create a tear out that
goes below your line. So if you have to stop short.
Okay once you're within about an eighth of an inch of your lines
it's time to switch over to a spokeshave.
The most important thing is this line right here. You want a nice shadow line.
This one down below doesn't really matter. You'll never look at it.
But this one should be really nice and clean and I like leaving this edge
rough sawn for the time being because it makes it
easier to see how clean that line is. Once I'm done getting this looking good
I'll take my plane and I'll just give this a swipe
and if it still looks good then I'll consider it done and if not I'll tweak
it a little bit.
Now it's important you don't be a slave to your line. You want to just make
sure that you're getting a nice clean finish. That's the most important thing.
The pencil line is going to go away.
Give that a nice stroke and check your work. It looks good.
You're ready to chamfer.
So I'm going to put a chamfer on this edge that's probably about three
sixteenths of an inch across its face. There we go. The last couple jobs is
just this little corner here which will soften a tiny bit.
On those ends.
And that's really done. All I have to do now is sand the face of it
and on to the other side. Time for oiling. I'm just using linseed oil
cut with about one third thinner. I'll start oiling on the back side
of my parts so that I can flip them over and have the
show side being up while the oil sets for a while.
And then when you're going to wipe down of course you
flip them over wipe down the back side first and then flip them over and wipe
off the show side again. Always a good idea to hit the end
grain a few times while you're doing this.
So it really soaks up the oil. There we go. Beautiful.
Quick look at some of the finishing details here. You can see how I've
scalloped this out to create a nice light looking reveal on the front edge.
Just like on the floorboards I put an arrow indicating which direction the
thwart goes because when you pull these out for
maintenance you don't want somebody putting them back in and having the
screw holes misaligned. And I've just put a little note in
pencil on the bottom as to when I built the boat and who I built it for.
And these all drop really nicely locking around frames. You could even leave
these loose if you really wanted to. We'll be putting screws in just the
same though. You can see how that scallop really sort
of makes that seat look like it's springing up a little bit in the center.
If I didn't do that it would actually look like it droops a little bit.
I'm not a big fan of finishing washers but I'm less of a fan of seeing
screws pushed right down through the surface of the thwarts.
All right well the thwarts are in and they look great. I love them.
Now in a traditional Grand Banks dory those thwarts would be
removable because those dories are intended to be stacked on deck of the
schooner nesting inside of each other. You might
have three or even up to six all stacked up in a row and you need to
get those boats all into as compact a format as
you can for safety on the boat and for
efficiency and all that sort of thing. So those thwarts get lifted out, dropped
in the bottom, next dory goes on top. That's probably
also why Grand Banks dories tend to have a very right
transom and stem. If you imagine those boats nesting together you need to get
those elements spread apart so that the next boat
can get in. So that would account for that. So anyway
we're almost ready to launch this boat but we have a few
finishing details left to go. We're going to save those for the next
episode. So please join us again. I want to thank you all for watching and I
especially want to thank everybody on Patreon who helps support
this channel and if you can help us out on Patreon, I'd really appreciate that.
Links in the corner or down in the description and I will
see y'all!
