Woodcarving How To: Carve a Simple Snowman From a Block of Wood -Full Tutorial

FreeHands
60 followers
29 Video Views·Oct 25, 2022
Alright guys, today we're going to carve a simple little snowman.
This guy right here.
I'm going to be using a block of basswood.
This is 1 1⁄4 by 1 1⁄4 by 2 1⁄2 inches tall.
If you want to do it different, you can double it or triple it or whatever.
But you can go 2 1⁄2 by 2 1⁄2 by 5 if you want.
But today we're going to keep it small and simple.
Just to do a real quick thing here to highlight my artistic ability.
This is our snowman.
That's how your kid would draw it.
How does that ball stay on top of that ball without falling off?
And why is the hat on top of the head?
So we just have to remember when we're doing this that if this is the ground,
this will be our snowman.
This will be our head.
And our hat is like that.
So this is a flat section here.
And there is none of this.
So nothing sits on top of it.
It's smushed down and the hat does not sit on top of the head.
It's basically part of the head.
Does that make sense?
So we have our block of wood here.
Let's find the center mark here.
You can measure.
Bring that all the way around.
Take center this way.
I always like to mark centers on everything.
So you know where you are half the time you carve it off.
It's a good guide.
So we're dead center here.
Let's make this the front.
Let's come down about half an inch.
And the back let's come down about 3 quarters.
So we have 3 quarters.
Half an inch.
And right away we'll just draw our line on that angle.
So that's what we got.
That's your half way line.
3 quarter all the way across the back.
Half inch all the way across the front.
Just drop your knife and put on your carving glove.
We're just going to start on the center line.
We're just going to do V cuts on all 4 corners.
And then we're just going to join the V's.
Make them about a quarter inch wide or so.
Now we're just kind of getting the rough idea of how everything is going to work.
So we got that.
Let's do the same thing.
Although we're going to take the corners off.
Let's just do the exact same thing on these 4 points of the hat.
Only this time we're going to do stop cuts.
We're going to come straight in and up.
And then we'll take the angle after.
Straight in and up.
And then we're just going to join those angles.
Alright, see that? Hat, head, body.
Okay, let's just round, not round, but just take all the corners off.
Just lightly, not too much.
Same thing on the bottom.
Pretty much the same angle as there, just do the bottom.
It's all rough right now.
Same thing on the bottom corners.
Just a rough bottom.
And then the same thing basically for the head.
Same angles here.
And the hat.
Alright, now let's just dig those out again.
Same as before.
So that hat is going to be on an angle.
So let's just take a bit of this top corner off.
We don't have to get down to the exact
top of the hat, but just so we know what we're working with.
Get a bit of an angle.
Alright, now let's just go around
and give that hat a nice healthy
3 sixteenths or so lip.
Same thing, we're going to go straight in and then down.
We don't want to go too thin
because that's a real easy spot to break, but
kind of coming down on a bit of an angle and then we'll cut up later.
I like to start on the hat because
if you break the hat early on you can turn into a toque
or you can change the hat. So nice to have the hat
done before the whole body and then be disappointed.
We're still in the rough stages
so we can keep cleaning it out to even it up.
But that's basically it. See how that's come down on an angle like that?
So now we can just get our knife in here and just cut that angle up.
Then we'll see what we got.
So now let's go around the top
again and we'll just make that a nice clean edge.
Maybe on this lip here, maybe you can come up just a little bit of an angle.
Then we're just going to take our knife and just kind of roll that up.
Alright, just a little
sixteenth of an angle or so down.
Then we'll just kind of roll it up. That cleans up all the knife cuts.
Just keep going around until it looks like a hat.
Take the angles off the corners. Take a little saw cut on top.
Cut that off. Then just go around and
clean it up. I think the other guy's hat is a little bit higher
but no matter. A little cut edge here.
You can see a little bit of the edge of the wood still.
Trim that all around. Make it round.
We've got our mark here. So all we're going to do now is just kind of
take little slices all around
the top of the head. Just kind of rounding
into the hat by just little cuts.
You can kind of see how that cleaned that up.
It just kind of rounds into the head like that.
Now we're going to do the same thing on the middle. We're going to round down to the middle
to the bottom of that cut.
Little cuts on the bottom into the V.
Rounding everything into that V.
You can redo the V as you go. Keep it clean.
Okay. Well that's rough.
Roughly the top head part done. Anytime you see a little bit of the original
wood you want to just kind of scrape that off.
And by going up and down you might have a little bit of a point in the middle.
You're just going to round off that little center part there.
You can see that. I don't have to tell you that.
Do the exact same thing from the bottom down but don't get too small on the bottom.
You want to keep the bottom nice and flat.
Take that and just round it down.
You can kind of see. My bottom is not perfectly round.
But that's kind of what I want.
And the same thing for the middle section there. You can see the flat spots.
Just kind of round it to the top
and to the bottom. And anywhere you see a flat spot just make sure
you get a knife cut on there so you don't have a perfectly flat spot.
You can see there.
You'll learn quickly. You can see when I did that cut
there's a bit of a grain of the wood when I cut one way or the other.
And that's how you learn the grain. Sometimes
you can go the wrong way and if you get a little bit of ripping or peeling you have to
turn it around and only cut the other way. That's just the way the
grain direction is and you just have to work with it.
You can't fight it because it will only make it look worse.
But the front of that guy, that's what we're going for.
Okay, now that we've got our guy here
all fairly rounded out with no big bumps or dips.
You can see he's still not perfectly round.
So now from the bottom of that V cut there
let's just go around, draw a line all the way around.
We're going to put a scarf on this little fella.
Just give it about a healthy
quarter inch, 5 sixteenths.
Draw a line all the way around him and then we'll do a little
knot here and then we'll just kind of
swing that scarf one way and
swing the scarf a little bit shorter that way.
You can see that. Now let's start on the very back side.
Stick your knife in, a little stop cut and just
enough that you know
there's something there. See that?
We don't want that to be too deep, it's just going to be the thickness
of the scarf. And keep smoothing
that too so there's no edges. Okay, all the way around.
See that? You've got three sides of a scarf.
Now we'll move around to the front. Okay, I don't have a scarf.
I don't even own a scarf to show you, but if I put a scarf around my neck, I'd bring it
around and then I'd roll over itself and bring it down. So
the center of that little scarf is like a, not a knot,
but it's heavier right in the front. So we'll translate that
onto our snowman. A little bit of extra bulk right on the
top there if you can see. So the scarf
is going to come in, but basically that front little
section sticks out even more. Okay?
Just trying to picture it. If we haven't come around
from the sides yet, we've got the scarf coming up on each side, so this little
front little tail here, we're going to take that right from the V
and we're going to do a nice straight cut down
on both sides and then across the bottom.
You can do a little bit of an angle if you want.
And then basically the same thing. It's going to come up
and this is where a V tool would come in handy too. You could just
draw it out with a V tool. Just come around nice and slow
and take that scarf.
We're just going to clean that up. We're always looking that we don't have
any little spots like that, so we're always rounding off all the little
edges all the time. Then we've got the scarf. We're just going to
take that teeny tiny little edge off there just to soften the
scarf. Not too rough. That's basically it.
Alright, then we'll go back. Grab my pencil.
Go back and bring those
lines back in and then we'll show this tail
doing the same thing as that here. Only this time
it's going to be the same as the side.
...
