How to skive: a basic leather work technique

Carving and making leather goods
49 followers
One of the basic techniques in leatherworking is skiving. I've heard it pronounced skiving as well.
I don't get too hung up on that particular which way is correct because it's basically
describing the noise that a knife makes as it's doing the process of cutting through the leather.
And really it's just a matter of taking a piece and thinning it down to where it tapers out
or to where an edge thins down. It could even be taking a very large chunk of it and thinning it
like a splitter would do. And there's a lot of different tools that are used for this.
There's some specialty tools that are made specifically for the job.
There's ones that are really good for doing edges. There's cheap ones with replaceable blades.
There's more expensive ones. I don't really use too many of these tools too often.
There's a couple cases where it comes up but I do most of mine with my round knife.
And the reason I will usually use skiving is on a strap or something like this. If you're going
to be laying it back and you want it to lay down nice and smooth and have a nice finished transition
where there's no lump there that's going to rub against either whoever or whatever the leather is
against. Or you want the pieces to transition really well because you're going to be stitching
it and you don't want there to be a piece of thread that goes over that edge that's just
exposed and going to get worn. So it'll lay down nice and smooth like on this knife sheath here
where I skived it off on the back side of this leather and now it
tapers out and there's no lump right there where those stitches are hanging over.
Another use for it is when you're glue splicing pieces of lace together.
You can skive both pieces and glue them together and then you don't have a big thick lump right
there or pieces that are sticking up on either side that are going to catch and you can actually
splice a piece of lace and make a longer piece of lace out of it. I also use it with softer leathers
like an upholstery type leather on making bags, purses, or even upholstery and I'm going to be
rolling the edge or I'm going to be stitching it and folding it back and I don't want a big lump
there like you would have if you did not skive it because that will sometimes print through.
You can see it right there as opposed to where it's been skived. And just as a quick example of
this is how it's done. I usually when I'm skiving I'll usually put on the
the flesh side of the leather not the grain side. Your grain side is still going to be
your strength of the leather and of course it's your finished surface.
And depending on the angle you hold the knife at it's either going to just
cut even or it's going to keep cutting down into the leather. So if you wanted to start
way back here and you hold it low you can keep cutting fairly straight like if you're going to
do a belt blank or something and you just want to take out half the leather. But you can increase
that angle just a little bit and it'll cut down in and keep working over any of the high spots.
And of course this takes a very sharp knife to do but then you can feather skive it out
and again it'll taper out basically to nothing and lay nice and smooth.
Again no lumps or bumps there. So you can see the difference between
this and that. Like I said it's very useful. I use it all the time in almost every project
and I consider it to be one of the basic skills that a leather crafter needs to practice.
So
some of these other tools like this one is used basically the same way the round knife is. It just
doesn't have the points off to either side. It's got sort of a chisel grind to it. It's flat on the
back and just ground on one side so it's a little bit different to the angle you have to hold it at
depending on which way you've got it turned. But basically works the same way as the round knife.
This is called a French edge skiver and it's basically a wide edge beveler and it's also
really useful for going along an edge and taking off like a 45 degree angle along an edge.
But it's not real good about working further back into the leather. Both of these use replaceable
blades. This one does not have a blade in it. It would be right here and you would drag it along
like this. This one's basically the same idea only you hold it kind of at this angle and drag it along
and it just sort of scrapes away a little bit at a time and the reason I don't use it very often
is because it only really does scrape away a little bit at a time and so you spend a lot of
time sitting here peeling away at your leather and I could have been done with this with a round knife
by now. But it's cheap. It's fairly safe compared to a round knife. I mean obviously there's still
a cutting blade that cuts leather so it can cut skin. And the blades are replaceable so people
don't have to worry about things like learning how to sharpen which if you get a round knife
you have to learn how to sharpen it. That is a quick basics of skiving leather.
