How To Test and Replace an Oxygen Sensor P0135

Allstar Auto
20 followers
28 Video Views·Oct 22, 2022
What's up guys, welcome to another episode. Today I'll be showing how you can test and replace the
oxygen sensor on your vehicle. Now if you do have a check engine light on your dashboard,
and it is for an oxygen sensor, you don't want to run out and just buy the sensor without
pinpointing where the problem is. Now in this vehicle, this is the oxygen sensor, this harness
right here. Now the O2 sensor can be perfectly okay, but maybe there isn't power, which is this
other harness. Maybe there isn't power getting to the sensor and that's why you're getting a
check engine light. Maybe you have a problem with an engine ground somewhere. So there are
a couple of tests that we can perform, and these are very easy to perform these tests. The only
thing you'll need is the repair manual for your vehicle, and also a multimeter. With these two
tools, you can really pinpoint where the problem is. Then if you do indeed need an oxygen sensor,
then you know once you replace the sensor you're in good shape. So that being said, let's go ahead
and let's begin. Now the harness for the front oxygen sensor is located right here,
and of course I know this just by looking at the repair manual, which shows me exactly where
the sensor is located. So in the first step, what we're going to do is verify that the sensor
is indeed receiving battery voltage. And the point behind this is if the sensor is not receiving any
voltage, then obviously it cannot work correctly. So we'll first check to see if we are receiving
voltage, and to do that we'll just need to disconnect the connection here, the harness
connector, like so. And then what we'll need to do is turn the ignition key to the on position. You
won't crank or start the car, you just turn the key to the on position. Okay, so now we have our
multimeter. Just turn it to the voltage section, and what we need to do is check the battery voltage
on terminal three, which is this guy right here. And again, I know this just by looking at the
repair manual. So now I'll take the negative lead and attach it to the negative terminal
on the battery. And as you can see, we are getting sufficient power. So now we verify that there is
power indeed getting to the oxygen sensor. Now if you just performed that test and you are not
receiving any voltage, check the harness back here. Look at these wires. Sometimes you may have a cut
or short somewhere. The first step I would do is make sure that these wires are in good shape.
If they are, then the next step which the repair manual will show is you can check the ECM.
But that being said, just go ahead. Usually if you do have a problem, it's because one of these,
I've actually seen these connectors melt almost and give you a problem. So just check your
connectors back here, and I'm sure you'll be able to pinpoint the problem. One other thing to note
is make sure that these metal tabs are in good shape. Make sure that they're perfectly straight,
they're not bent up in any way, and avoiding to make contact. Those are really the areas you want
to look at if you're not getting any voltage reading. Now once you finish with this test,
then we can move on to the next step. Now the next thing to check according to that flow chart
is the engine ground. And again, there's a diagram showing where the engine ground is,
and there are these two connections right here. This ground looks perfectly fine to me.
You can do a voltage check, but just visually looking at it, everything looks pretty good to me.
If you have a lot of corrosion, if these connections are loose, then of course that will
give you a bad ground. But just take a look, make sure everything's nice and tight, there's not any
corrosion, everything looks good here. Okay, so now we verified that the sensor is getting power
from the vehicle. So now the next step is to go ahead and check the sensor itself. And to do that,
we need to do an ohms reading. And this is just a different setting on the multimeter. So go ahead,
as you can see here, we're in the voltage DC, which is direct current. We need now to get into
the ohms section on the multimeter. And now if we take a look at the repair manual on our first test
between terminals three and one, we should have 2.3 to 4.3 ohms of resistance. So let's go ahead
and check that. So there you go, we have 4.1 ohms of resistance between terminal one and three.
And now we need to check the continuity between two and one, terminal two and one. And we should
have no reading here. So let's take a look. So we're okay there. And we also need to check between
terminals three and two. And there we go. So we're in good shape. So now we verified that power is
getting to the sensor. And we've also verified that the sensor is in good shape. Now in this vehicle,
I'm really doing this just to show you guys how you can perform these tests. I don't have a
check engine light on right now. But if you do have a check engine light for your oxygen sensor,
or if you have a P0135 reading, this is the exact thing that you want to do. Of course,
again, get the repair manual for your vehicle because they'll show you exactly where the oxygen
sensor is located. And they'll also give you different readings as well. If for some reason,
if you did not get a resistance or ohms reading with terminal one and three, or you did get a
reading with terminals three and two, and two and one, then you have a bad sensor and you need to
replace that. So I'll show you how you can do that. And before you begin any work, any electrical work
on your vehicle, make sure you always disconnect the negative terminal on the battery. So you
disconnect this. And now we need to remove the sensor from underneath the car. The way you could
find the O2 sensor is it's plugged in or screwed into the exhaust. With my wrench over, I have the
round part. It's not the box end part. It's the round part over the sensor. And a lot of times,
these can be really difficult to remove. Sometimes what I'll do is I'll tap the end with a hammer or
even a mini, a very small, I have a small sledgehammer here. Right, I got this guy right
here, small, maybe three pounds, and tap the end of this. I can't do it lying on my back and holding
the camera in the same time, but just tap it loose and she'll come right out. This is what the new
sensor looks like. As you can see, there's a protecting cap over the end of the sensor.
And I did check. If you pop this off, there is, from the factory, you have anti-seize compound
already rubbed on there. So you're good to go on that. You don't need the compound. Just make
sure you have it. If you don't, put a little bit on there. Again, it's called anti-seize compound.
Should be rated to about 2,000 degrees. All right, so this is the new sensor reinstalled
in the vehicle. It's too difficult for me to tape and reinstall the sensor at the same time,
but you get the idea. If you remove the old one, just reinstall the new one,
and then plug everything back in on top of the motor.
