Is it Possible to Revive a Dead Battery with Epsom Salt - See For Yourself

Allstar Auto
20 followers
36 Video Views·Oct 21, 2022
Hey, how's it going do-it-yourselfers? Today we're going to do a bit of an experiment and
see whether we can revive this 12-volt car battery with some basic household products.
And by that I mean some Epsom salt, baking soda, and some distilled water.
And here's exactly how dead this battery is. As you can see, it's only got 3.95 volts.
Now with that voltage, putting a load tester on this battery is pretty much pointless,
but here it is anyway. So in a good battery this style would need to be here,
where it says okay. And when you put it on under load by pressing this button,
it's supposed to go to this green area and show you the amount of
cranking amps it has. But as you can see, it's already in the red all the way down here,
and when you press this, it goes to pretty much zero.
So first things first, we're going to clean our battery terminals and wipe down the top
of our battery. And if you don't have a battery terminal cleaner, you can always just use some
400 or 300 grit sandpaper. So in the next few steps, we're going to be removing these
battery cell caps and then pouring out the acid that's in this battery. So make sure you do this
in a well-ventilated area and also wear gloves, because if the acid gets on your hands, on your
skin, or even on your clothes, it's going to burn through it and it's not going to be pleasant.
And on this battery, these caps can easily be removed with just a flathead screwdriver.
There we go. There's one, and here's the second one.
And next, we're going to dump the acid that's in this battery into this plastic container.
I should be probably wearing long sleeves for this, but
you got to work with what you got.
All righty. So next, we're going to get about 10 ounces of baking soda,
and then we're going to mix that with about one gallon of distilled water.
Now, the best way to mix the baking soda with the distilled water is to just do it in small
amounts. Just get some distilled water, put it in a container, get some baking soda,
and then you want to stir it until it dissolves into the water.
And next, we're going to start pouring it in and filling each cell. Make sure you go very slowly.
All righty. Next, we put our cell caps back on,
and then we're going to shake it around our battery for about 30 seconds or so.
After that, we remove our caps once again, and then we're going to dump the solution in our bucket.
Next, you want to mix about 15 ounces of Epsom salt with about one gallon of distilled water.
And similar to the baking soda, you want to mix this slowly,
but also you want to make sure you heat up the water.
That way, you can stir this and dissolve the Epsom salt into the water a lot easier.
And next, we'll fill up each cell with our Epsom salt and distilled water solution.
Next, we grab our charger, and we're going to slow charge this battery for about 24 hours
on the slow charge setting. We're also going to leave the caps off because sometimes you
have some overflow problem. Just when the solution heats up, it's going to overflow.
So you don't want to put the caps on and have any buildup underneath it.
So again, do this in a well-ventilated area, and also be very mindful of whatever you put
this over while it's charging. And as you can see, I got this on the floor, so it's pretty safe here.
All right, so it's the next day, and it's been about 24 hours since this thing's been on the
charger. So let me show you what we have. All right, so as you can see, we've got about 11.3
volts, which is a huge improvement from where we started, but it's obviously still not good enough.
So what I'm going to do is just to put it back on the charger, but also on this battery,
we haven't had any overflow issues. But if you have, make sure you refill all these battery
cells with distilled water and Epsom salt solution. And I'm also going to use this
newer battery charger just to make sure our battery charger is not the problem. And again,
we're going to put this on the 2 amp setting, or in other words, trickle charge the battery.
All right, so it's been another 24 hours since this battery's been on the charger.
Let's see what we have now. Now, this time around, I don't know if you guys can see,
but we are having some overflow issues. Not a whole lot, there's still plenty of
solution left in the battery, but we do have some water coming out of these battery cells.
Here's a look at our charger. We're at 100%, according to the dial, but we still don't have
the green light, which would indicate this battery is completely charged, but we're going
to go ahead and check our voltage on the battery anyway. All right, so first we'll wipe the top of
our battery, get it clean. And next we'll grab our multimeter, but make sure if you're missing
any distilled water to add water to these battery cells, you got to make sure the lit
plates that are inside here that you might be able to see, they have to be covered with the
distilled water and Epsom salt solution we made earlier. And here's how much voltage we got now.
We got 12.43 volts, which is actually pretty good. It should be 12.6, but this multimeter
may not be exact. As some of you may know, each battery cell in this battery should have about
2.1 volts, which would add up to 12.6, or well within the margin of error of 12.43 or whatever
we just got. That. Now, even more important than the voltage is how many amps this battery
can put out. When we press this and put it under the load, we're going to hold it there for 10
seconds, and then we're going to take our measurement. It should come down to about 700
amps, which as you can see, it's the amount of cranking amps this battery is supposed to put
out according to the sticker. All right, here we go. That shut down way too much, but anyway,
we're going to hold it there, see at least if we can hold that at least. I would say it's probably
about 100, I guess, 100 amps it's putting out, and that's 10 seconds. All right, so you can put
100 cranking amps, that's pretty low, but it's still a huge improvement from where we started.
But what we can try to do to raise the cranking amps it puts out is to cycle the battery.
And to cycle the battery is to basically drain the battery and then to recharge it. Now,
you can do this by just sticking the battery in the car and then turning on your headlights,
but I got this spare headlight laying around, so I'm just going to use this.
And you know what? Actually, I'm just going to attach the second headlight as well just to make
this go faster. And then we're just going to wait until the voltage reaches about 10.5 to 11 volts.
All right, so it's been a good few hours and we're actually down to closer to 10 volts,
but it's okay. So we're just going to take these off and then reattach our battery charger.
And we're going to charge this for about 24 hours again or until we get a green light here saying
our battery is fully charged. All right, so it's been about 10 hours actually this time,
and I believe we're done. But I say that because not only the dial is at 100%,
but we also have a green light telling us our battery is fully charged. And again,
we've got a bit of an overflow issue here, so next I'm just going to quickly clean this up.
All right, so first let's check out our voltage. All right, this time we got 12.66 volts. Again,
that's about right. We should have about 12.6 volts. But again, here's the real test. Our load
tester showing us how many cranking amps this thing can put out or whether we've made any
improvements. Let's see. God, that's a bummer. No improvements at all. It's in the same area as
before. Oh, well, it was worth a shot. This is holding steady there, and it's not going into the
showing us that it's bad. Well, it shows us that it's weak, but it's not improving much.
And there you have it, folks. So if the question is whether you can revive a dead battery with
some Epsom salt and baking soda, the answer is maybe. You just might be able to. Now,
we started with a really good battery. This battery, again, had 3.95 volts. It's putting
no amps at all. After we treated it with the baking soda and then the Epsom salt,
now we are up to 12.6 volts. And I'm wondering whether that's going to retain that voltage
overnight, though. I'll test this tomorrow and make a note of it in the video when I put out
the video on YouTube. But I can see it helping a battery that's in better shape. Maybe you've
got a battery that's in the back of your garage putting out only maybe eight or nine volts,
and you do this, I can see that turning into a good battery. But we won't know because I don't
have one of those around to test. But if I ever do, I'll make a follow-up video and we'll know
for sure whether this can help a dead battery be good again. So with that said, I hope you
enjoyed watching this little experiment that I did. If you did, please give it a thumbs up
and also consider checking out some of my other videos. I'll put it up on the screen as video
links so you can just click on it. All right, thanks for watching. See you next time.
