DPF sensors can be a source of many regen issues and sometimes difficult to know when to replace or not. This video walks through the steps outlined in Cummins Quickserve on troubleshooting various Sensor fault codes with a surprising result! #diesel#mechanic#dieselengine#dpf#dpfsensor#dieselrepair
In this video, we tackle a common issue for every mechanic: testing a diesel particulate filter (DPF) differential pressure sensor. We're diving deep into the diagnostic process, referencing Cummins troubleshooting charts to ensure accurate sensor health checks. This is crucial for anyone working with automotive technology, as understanding these systems helps maintain optimal vehicle performance.
All right guys so this is a really popular topic and I was really hoping to have some
clarity on the easiest quickest way to test one of these sensors that tells you the restriction in
your diesel particulate filter and I'm looking in the Cummins troubleshooting chart you can see I
got open up here to Cummins quick serve and what I found out is that I was thinking that like with
most things I would take this connector apart here and be able to go inside there and measure
resistance in the connector and find out or the sensor and see if the sensor is good but it's
weird that when I'm going through the troubleshooting chart it tells me the obvious things that I was
going to tell you guys about anything so one take your tubes check in for excessive soot buildup
I blew this out and I tried to clean it up inside a little bit took a q-tip to it got hardly any
soot at all which is really surprising for this guy but so there wouldn't have been any problems
with this no soot in the connectors I did the same thing with this one I haven't finished putting it
back together yet but then when I was looking at the other parts you know it says to inspect the
pins inspect the wiring harness you know so you'd want to take a look at all these guys make sure
they're in good condition and then at the part where this goes into the computer take it apart
look at the pins but really when we're looking at this one what it tells us to do right here is to
measure resistance between the supply pin and the signal pin in the wiring harness and check it
against all the other pins in the ECM connector so really what they want us to do is go over here
to the ECM disconnect the ECM and then find with the wiring schematic which pin on the ECM
connector is the return and which one is the signal wire for that sensor and then check resistance
between it and all the other pins on there looking for a short basically and then it tells us right
here that we want to see if resistance is less than 100 ohms then it tells us that that means
we have a malfunctioning OEM wiring harness and then if you scroll down a little bit further
though I was expecting okay but how do I check the sensor itself well that's where it gets kind
of weird because down here at the bottom you got the after treatment DPF differential pressure
sensor is malfunctioning and basically it says to replace it if all the other stuff you have done
basically wasn't good so honestly it's wanting us to replace this sensor if we've made sure there's
no blockages the wiring harness is good the pins look in good condition and we're still
having an issue then that is telling us to replace the sensor so unfortunately this one is
one of those weird ones where you know you can't just go in here and connect to these pins and
find out what the resistance is internally at least not according to Cummins I'm sure there's
probably some sort of expert out there I think this is a Bosch sensor that would be able to tell
us maybe what how we could test this but this is kind of a one where you just basically eliminate
all the other possible suspects and if nothing else is left they're saying replace this sensor
so yeah again this wasn't what I was expecting when I started filming this video I wanted to
be able to you know and I even got the DMM out and I was going to say hey so we were to check
these pin and this pin and see how much resistance we got in the sensor and so forth but nope that's
not the case so but I do hope this cleared up a little bit you know check the tubes check the
pins and connectors make sure everything's in good condition check the wiring harness for shorts
right check the pins make sure there's no connection between any of them that's that the
resistance isn't less than 100 ohms of resistance and then if everything checks out then saying to
replace the sensor what would lead you to doing all this in the first place basically what I found
this information was I did a troubleshooting so what I did is I went in let me show you guys
into Cummins quick serve went into the fault code troubleshooting manual right here which opened
this guy up I did a quick search for DPF sensor and then I kind of scrolled down a little bit and
found some fault codes right here for differential pressure being erratic abnormal intermittent
and I clicked on these and the troubleshooting chart was the same on basically all of them
and that's the stuff that we just talked about if you didn't have a fault code something else
that might lead you to the sensor potentially being an issue without a fault code would be like
excessive regen times regening a lot a bunch of different issues but if you try to do a regen
it runs the regen but it gets really hot but it's not reducing what they say the soot level is
you could have plugged up tubes you could have a damaged sensor and that could lead you kind
of into that same troubleshooting category and area but I'll just clear it up a little bit of
the troubleshooting that you might have to do with these DPF sensors if you have any specific
questions that I didn't cover if I know the answer to it I will answer it just ask in the comments
but yeah so basically sensor is bad via process of elimination thanks