How to Mud and Tape Drywall - Part 1 of 2 - Mudding and Taping

Handy Creators
62 followers
10 Video Views·Oct 13, 2022
This video is the first of two that explains how to mud and tape a room once the sheetrock is hung. Part 2 is here: needed:
• All-purpose joint compound
• Topping joint compound
• A 3" putty/drywall knife
• An 8 - 12" drywall knife
• Drywall tape or mesh tape
• Respirator and safety glasses
• Sanding sponge or sanding supplies
I appreciate any tips, tricks or suggestions you have. I don't claim to be a professional and I'm always learning but I help this video encourages you to give this a try for yourself - it's really not too bad. I was very intimidated by mudding and taping until I tried it myself. Happy DIYing!Credit: LRN2DIY
Hi, I'm Nils and today I'm going to show you a little bit about mudding and taping and
what I've learned in the process of finishing my bathroom here.
This is the finished product.
I'm basically going to try to create this sort of texture that you can see on the walls
and we're going to show you first how to, once you finish the sheetrock, how to do the
mudding and taping to get the walls all smooth and then this is a two part series and then
in the third section you can see how to do the texturing itself and create this, sand
it down, get it all smooth and ready for painting.
So, let's go ahead and get started.
Alright to get this corner here I've got some all purpose joint compound and I'm going to
take my three inch knife and just try to fill in, in this case I've got a fair size gap
here in between the boards of sheetrock so I'm just going to come in here and try to
fill that in as much as possible and get it ready for some tape to go on there, making
sure to add as much as I need to, up in the corner here for example, just make sure it's
all filled.
I'm going to apply this stuff pretty liberally and be real generous with it, so I'll scrape
off the excess in a minute with the tape.
So with this gap I'm probably going to need to do a lot of that kind of action to get
in there and get that gap filled in, if I hold this at a little bit of an angle that
will help but it's still not going to get it all.
And then with the tape itself, I've already done the rest of the wall here by where the
camera can't see, I'm just going to grab this tape and as you can see it kind of easily
folds, there's a corner type and there's a straight type, so I'm going to grab the kind
that folds here for my corners and get a measurement of all the way down to the floor, I could
be real precise and measure it, but I'm just going to kind of wrap it here, and let my
foot rip it off and just go ahead and pre-crease it, fold it all the way down and then apply
it right into the corner.
We're going to press this in lightly, so I'm going to press this in with my fingers pretty
lightly into the corners here, I'm just making sure that the corner itself of the paper
is in the corner of the walls, and once it's in like that, I'm going to clean my knife
off, go ahead and press that up into the corner, and then there we go, and start to just push
it down, getting some of this excess mud off and taking it off as I go, got to be careful
not to push too much into the corner, especially on this side because it's not solid back there
behind it, so I've got to make sure that as I'm pressing I'm not tearing the tape because
that's not going to do us much good, and as you can see it kind of pushes itself right
into the wall, get all that excess off, and I'll just follow this all the way down, and
that's how I do a corner.
So this is the first coat, you're probably going to want to come back with a second coat
to smooth it out and get any little pieces like this that we miss, after this is dry
we'll come back and get that probably with some topping joint compound rather than the
all-purpose.
Alright, the next joint we're going to do is just this straight wall joint, and these
are non, well I've got one manufactured joint against one hand cut joint, and it's a pretty
sloppy cut as you can see here, so we're going to have to do some filling in, so I'm just
going to apply a bunch of mud to fill in that gap there, I've already done the bottom
section here as you can see down below here, so I'm just going to fill this in, I get some
good amount of mud on the sides to act as adhesive basically for the tape, now the gap's
filled in so I'll just run it up and down the sides, leaving a nice layer of it, like
that.
Do the same thing on the other side, alright now I'm ready to go ahead and put some tape
on there, and then we're going to put it on the tape, measure this out, and try to make
sure we get it centered over the joint, and then just lightly press it down, all the way
down to the ground.
Okay once we've got that we're going to make sure the knife is clean, and just like before
we're going to go through and push it down, at first you kind of have to pull it to wipe
off that excess, and just keep on going all the way down.
