DISCLAIMER: Got2Learn is NOT responsible for any damage done to a property of which the plumbing wasn't done by a professional, I do not recommend doing your own plumbing if you are unsure about what you are doing, always hire a LICENSED contractor when doing any type of plumbing so you can be covered by insurances if something does happen, these videos are for entertainment purposes only!
What's up guys and welcome back to another video.
So I've been making a lot of soldering videos lately such as how to solder in a confined space,
how to solder like a pro without getting any drips of solder all over your pipes,
but I've never talked about soldering a vertical joint before.
And in this video I'll be showing you an easy step-by-step fashion how to do it
and I'll give you all kinds of cool little tricks to make it that much easier.
So let's get started.
So why make a separate video just for a vertical joint?
I already watched your how to solder copper pipe video, isn't it the same thing?
The answer is no because the joint that was soldering was a horizontal joint
and soldering a vertical joint requires a totally different approach.
Here are some reasons why.
On a horizontal joint you apply your solder without any restrictions as such,
but on a vertical pipe the bottom joint needs to be able to wick the solder upwards
and fight gravity so to speak.
So I'll be covering how to ensure it's done properly.
The second reason is the heat.
Heating the joint properly on a horizontal joint is important
but even more important on a vertical one.
So I'll show you my way of doing it which never leaks.
And lastly is supporting the pipe.
I'll be showing you three quick ways to temporarily support it for it not to fall
as if it does fall it could end up looking like this which would mean it needs replacement.
So what tools and materials do I need?
You'll be needing a torch,
some gas,
a cheap igniter,
something to clean your pipe and fitting,
a rotary cutter,
a deburring tool,
some solder,
some flux,
and a clean rag.
The torch I use when doing half inch to one inch pipe is this one right here.
It works just fine and it only costs around $30 so it's great for budget repairs.
Also, the fact that the flame isn't too big like pro torches,
you don't need to worry as much for setting your surroundings on fire.
As for the type of gas, I just buy the blue propane bottles.
The yellow bottles, also known as map gas,
isn't really map gas anymore as it was discontinued in 2008
but kept the map name for marketing purposes
so there's no real difference between both of them anymore.
My torch doesn't have a built-in igniter so I'll need a striker to ignite it.
These only cost around $4 to $5.
As for cleaning the pipe and fitting,
you'll need some sandpaper or an abrasive pad for the pipe
and a wire brush for the fitting.
I prefer the scotch-brite type pads to clean my pipes
as they tend to slip less in the hand as opposed to these rolls of sandpaper.
And for the fittings, you could use the same thing
but it's a lot easier to use these brushes to get it done.
And plus, there's a cool trick you could do with these
to speed up the process which I'll show later.
To cut your pipe, you'll need a good rotary cutter.
I don't suggest getting the $5 cutters as they cut crooked and they're just hard to use.
The best cutter for the price in my opinion is the autocut cutter.
It's only $15 and it works like a charm.
Here's a review I did of it not too long ago.
Whenever you cut a pipe, you need to deburr it.
If I'm soldering the copper pipe,
I prefer using this type of deburring tool as it's lightweight and easy to carry
but it only deburrs the inside of the pipe.
If you were installing ProPress or SharkBite for example,
you'd need to deburr the outside as well.
This is where these come in handy as they do both the interior and the exterior of the pipe.
Also, you'll need some lead-free solder and water-soluble flux.
I'm using the Audi brand for both but any reputable brand will do just fine.
Just make sure you see the lead-free logo on your solder and lastly, a good clean rag.
Alright, with that out of the way, let's get on with the real stuff.
Here's the setup I'll be demonstrating it on.
I have a 3 quarter inch copper line and I'll need to solder on a coupling with a piece of pipe,
an elbow and a cap at the end of it.
So to start, the first thing you want to make sure of
is that there's no water dripping from the pipe.
Water is your worst enemy when trying to solder.
If there's any water leaking, it means that you have leftover water in the system
or a faulty shut-off valve which needs to be addressed.
I made a video on this subject on how to counteract any water in a system
that will help you a lot if you have this problem.
I'll link it right here and in the description box below if you need it.
Once you got it to stop leaking, if it was, you could start with the preparation.
Go ahead and cut the pipes you need to cut
and use your sandpaper or abrasive pad to clean the pipe ends.
A bit of advice here is don't cut corners when it comes to cleaning your pipes and fittings.
Preparation is 90% of a job done right, so take that extra time to do things properly.
You might get lucky on a horizontal joint,
but when it comes to vertical joints,
they must be spotless in order for the solder to wick upwards and fight gravity.
Here's a side-by-side comparison of a properly clean fitting in pipe
and an improperly clean fitting in pipe.
The properly clean ones are nice and shiny
and the improperly clean ones still have some unclean spots,
which would most definitely prevent your solder from joining both the pipe and fitting together.
A cool gadget that I use all the time now and that speeds things up
is this drill attachment.
Just chuck it up, insert the pipe, and brush it under 3 seconds.
Neat, huh?
The same thing could be done with your fitting brush.
Just cut off the brush portion and chuck it in your drill.
It'll speed things up quite a lot.
Now, onto deburring.
I can't stress enough on how deburring is crucial for a good installation.
I made a very thorough video on this and why exactly it must be done
and all the consequences your system will have if it's not.
I'll leave a link here and below with the others
and I strongly suggest watching it to get a clear understanding of why it's so important.
So, now that the pipe and fitting are clean and deburred,
let's talk about the fluxing part.
The flux has a major role in the process
and that's to keep any oxides from building up on the surface of the pipe while it's being heated.
Being an acid, it also cleans the copper from any greases or oils that may have been on the pipe.
Here's another side-by-side comparison of solder being applied to a flux pipe
and one without.
On the pipe without flux, it may look normal,
but oxides got in between the solder and pipe
and didn't allow for the solder to properly adhere to the surface
which would guarantee you a leak.
You'd also want to be careful not to cook off the flux as you're heating the joint
as it would give the same result as if you hadn't applied any.
So, how much flux do I really need?
You really don't need that much.
I simply apply a thin layer on the pipe and not in the fitting.
I noticed that by applying some in the fitting,
when you insert the pipe,
it basically scrapes it off and pushes it into the fitting as seen here.
On small projects like this one today, it's fine.
But on big projects, it could take months before the flux is washed out from the system
allowing it to eat the copper and corrode it.
So, only apply a thin layer on the pipe and you should be fine.
You could also use tinning flux
which helps to get full solder coverage because of the solder powder that's in it.
Alright, so all of the above is completed.
Now, let's move on to the next step which is to secure the pipe.
The first thing you want to do before actually soldering
is making sure that the vertical pipe is well supported.
Let me show you why.
As you heat a fitting, it expands just enough to let go of the pipe
which could get very frustrating.
So, here are three ways that I know of of temporarily making it hold in place.
My least preferred way of doing it is to pinch the coupling with a set of adjustable pliers
and rotate the pipe.
This will give it just enough tension to hold it while you're soldering
but it could prevent the solder from going where it was pinched.
So, the next trick which is easily accessible is to get a piece of wood,
cut it to length and jam it in between both studs.
When you're done, just tap it to remove it.
And the creme de la creme of all tricks is to grab your tape measure,
lock the blade and set it to the correct height.
This method works whenever and wherever you need it
and what's fun is that every plumber has a tape measure.
Pretty cool, huh?
And now, on to the final step, soldering.
When I'm soldering half inch to one inch joints on vertical setups,
I prefer heating the middle portion of the fitting.
Here's why.
By heating the middle portion, the solder for both the top and bottom joints
will go towards the middle where you want it to go.
But let's say we do this again but this time we'd heat only the bottom joint
as opposed to the middle.
You'd be able to solder the top joint but when you'd get to the bottom one,
the heat would pull the solder from the top joint into the bottom one and overflow
as the heat attracts the solder.
This would cause a dry spot which would most likely leak.
Now, a joint can only take so much solder.
So, it's either gonna drop out or drop down inside the pipe
which are two things you don't really want.
Here's what overfeeding a joint looks like.
The solder will settle at the bottom of the elbow and restrict flow in the system
which is not good.
So, a cool trick I learned when I first started as a plumber
to gauge how much solder to use is to bend the tip.
But why exactly?
If you're soldering half inch pipe,
the joint generally requires about a half inch of solder.
So, bend the tip half an inch for a half inch pipe
and if you're soldering three quarter inch pipe,
bend it three quarters of an inch and so on.
This will give you a good visual indicator of when to stop applying it.
So, go ahead and circle around the fitting as much as you can.
Always staying close to the middle part of the fitting
and probe the joint every five seconds or so to test if it's hot enough.
A common mistake I see at this stage is when a beginner heats the actual solder.
This will only break the solder off and won't do much good.
So, always heat the opposite side of where you're applying the solder
to make sure this doesn't happen.
Now, keep probing it and when the solder starts to melt,
remove the heat as to not burn any of the flux.
Good!
Then, do the same thing for the bottom.
The bottom joint should take less long to melt as the fitting is already hot.
So, once again, apply some heat in the middle
and as soon as you see the solder melt,
remove it, apply your solder,
and let your joint rest for a few seconds before touching it.
What I like to do at this point is to solder the rest of the joints
which lets the first ones cool down
and then I wipe off any excess flux left from soldering.
If you skip this step,
the leftover flux will cause vertigree on the pipe and fitting
which could eat through the copper in the long run.
So, always wipe it clean.
And that's how to properly solder a vertical joint.
This, of course, is my way of doing it
but other techniques may work just as well.
So, do your research and use the technique that's most comfortable to you.
And as usual, if you guys learned something from this video,
please give it a thumbs up, share it, and subscribe to the channel.
And until the next one, thanks for watching!