Awnings are literally a cool addition to add to your home. We had fabric-covered units and didn’t like how they performed or looked - so we re-skinned them with metal. You can do the same thing!
The south-facing windows on our home have awnings on them. The summer room temperatures in those rooms are almost impossible to control without the windows being shaded. We love what the awnings do for creature comfort, but we were not pleased with the covering performance or appearance of our awnings.
A common approach for awning coverings is specially treated fabrics meant to resist the sun's ultraviolet (UV) rays - which fade and “sun-rot” the fabric over time. The first coverings we had were a dark gray, but they didn’t last long and the manufacturer replaced it with our choice of a more sun-resistant fabric (even though the first one we had in the original installation was supposed to be). We saw fading and discoloration beginning again after a couple of seasons, and frankly, we didn’t like the striped look - it didn’t go with anything else on the house!
DirtFarmerMaggie suggested we cover them with metal. At first, I thought this was a way too ambitious project, but the more I thought about it, the more it made sense. We were getting the house painted, and white metal awnings would look and perform WAY better than what we had.
Join me as I walk you through the process of “re-skinning” the awnings, and some tips and tricks learned along the way. While we were able to “repurpose” our existing awning frames, you may not have that luxury and need to start from scratch.
If you do, here are some basic dimensions and proportions to remember. First, you want the shade about the top 2/5ths of the window. That means that the bottom edge of both the front and sides of the awning should not rest any more than about 2/5ths of the distance from the top of the window and certainly more than one-half.
Second, you can have the front edge be narrow, or have a skirt along the front (like we did). We think the skirt, which is about 4” tall, looks classy.
Third, the angle the top runs down is about 45 degrees (or for you roof builders - 12/12 pitch). Fourth, overbuild. Attach skins to the framework with lots of pop rivets where the connection allows and use lots of “metal-building” screws elsewhere. These units are going to be exposed to the elements - including high winds, so make them stout.
Finally, the frames are attached to the house using specialized clips that the awning hangs on, and then the bottom of the sides are drilled into the house. These are not moving!
We are really pleased with how these turned out. Not only do they look fantastic and are extremely durable - but there’s NOTHING like the sound of the rain on them.
Sure, you can have someone do this for you, but why? JUST DO IT YOURSELF!
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
We have a massive south wall on our home
that gets a lot of summer and other seasonal sun.
Makes those rooms on that side of the house
really hard to keep temperature controlled.
We added awnings, but we weren't happy with the results
because they were fabric, they faded,
and we upgraded to metal.
Let me take you through the process.
You'll love the results.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Recently, we upgraded our old fabric-covered awnings
to new metal-covered ones, and we love the results.
You can see how they look on the house here.
They are really attractive,
and there's nothing like the sound of rain
on a metal shutter.
We started originally with these gray fabric-covered ones,
but within a year, they faded out,
and we called the company back,
and they said, hey, we've had some problems with that.
Here's these other fabrics that we can guarantee,
and we ended up with these kind of striped ones
that kind of look like a beach place,
but we live in the desert west of the United States,
so that didn't really work out really well.
And I'm preaching the choir a bit,
but awnings are very popular fixtures,
whether they're on commercial buildings,
you see them at retailers,
and they're just a great addition,
but we wanted to get that great look with durability.
Well, if you take a look here,
you can see when we pulled this off of the building,
this is the fabric awning the way it looks.
And let me show you right here,
this is some of the material right there.
Now, while it's very durable for an awning,
you can also see the hem that we pulled out here.
This 28-gauge metal right here,
this ribbed metal, is a lot more durable,
and it costs about a buck 65
at the time of the filming per square foot.
You're gonna need to buy about 20% over
on the square footage
once you calculate what you're recovering.
Now, when it comes to installing awnings on your home,
you can fabricate your own,
you can have somebody make them,
you can buy a kit.
When you do so, there's some basic ratios.
This video's not going to be a step-by-step
with dimension drawings,
but here's some rules of thumb.
Number one, you wanna cover about 2 5ths
of the top part of the window.
Number two, the top slope should be about 45 degrees,
and it should project out past the window
at least two foot, sometimes deeper,
to give adequate shading.
And we like the side panels
because that gives more shade
as the sun arches over in its path across the sky.
So those are some basic ratios that you'll need.
Let me take you to the process we use
to take the cloth off and install the metal covering.
The first thing you need to do,
you can see here how the fabric's stretched over it,
but one of the things is retaining strips
that cover the channels where the fabric was tucked
and stapled into these special extrusions.
So you can see here you need to pull those out,
and they're on the top slopes
and along the bottom edge for cosmetic reasons.
So you'll have strips of fabric left over in the channels
that need to be removed
anywhere where they're gonna interfere
where the metal's gonna overlay.
So what we did is we grabbed some of those torn strips
with a needle-nose plier and simply rolled it up
to create high leverage to pull those strips out.
When we began with the side panels,
we wanted to make sure that everything was symmetrical,
and so we took the distance of the ribs and the metal
and centered it along the side
so you end up with this really nice appearance,
not everything spaced out and then a leftover on one side.
We worked from the center out.
Did that on both ends,
and later we'll do that on the lid
and the front skirt as well.
So after we had those end pieces cut,
then we went ahead and clamped them to the frame,
drilled them with an appropriate size bit
for the rivets we were using,
and used a pop rivet gun to fix these securely
onto the sides of the end frames.
Use an excess of pop rivets instead of going sparingly.
These things are gonna be in the wind,
and you wanna make sure they hold on well.
After the end panels are fixed,
everything's solid,
now it's time to move to the front skirt.
In this case,
cutting these kinds of pieces of metal like this,
the toughest part is not when you're cutting in the flat,
it's going over that ridge.
And so we opted to use a metal cutting blade
and our bandsaw,
and if you've got that option,
it's a great way to cut strips.
We just set up a temporary fence
and then ran the strips through
and made plenty of stock at the right width
for each of the four awnings that we had.
If you don't have a bandsaw
and you need to manually mark the lines for hand cutting,
what you'll need to use is something like a metal yardstick
and side along the edge
so that you get a true line
that goes evenly from side to side
and doesn't meander as it climbs up
and over each of the bumps.
All right, now that you have those front skirt strips cut
and ready to be affixed,
you wanna use the same approach you did on the side panels.
That is find the center of the width of the awning,
mark that,
and then find what's the best center to put the strips in.
Is it one of the upward humps on here?
One of these right here?
Or is it in the middle in the field
where it needs to be centered?
Determine that for your size awning
and then lay out the strip
working from the center out to both sides
and cutting off the excess at the corner.
Once you determine the placement,
the center in the front skirt
and have cut off the ends there,
now it's time to affix it using pop rivets,
drilling the holes, putting the pop rivets.
Again, be generous.
Now, if you've got an extrusion shape
that does not allow the pop rivets to grip properly,
then you'll need to change
to one of these type of screws that are washered,
have a hex head that you can drive in with a driver,
and they self-tap.
So this will work very well
for making sure that you have adequate fastening.
Now that you've got the whole skirt fastened,
it's now time to put on the lid.
And we have found that, generally speaking,
you're going to need to splice the pieces together.
You wanna make sure that the pieces overlap
and line up with the front skirt.
That is, anywhere there is a raised ridge
on the front of the skirt,
the adjoining piece comes down over it in the same place
and creates a nice seal.
You don't want a big gap that you're gonna see
when the awning's on the side of your house
and you look up and see a big bump hole there.
You want them nesting into each other.
Once you determine that,
it's time now to cut the main sheets on the top.
And again, use the pattern on the front skirt
to work right and left.
Fasten the top in place using pop rivets.
And again, these types of screws, if it's necessary,
be generous.
I keep saying that
because these are gonna be in the weather, in the wind,
and you want them to be solid and hold everything in place.
One other thing that you wanna make a determination on
is how far the lid is going to over-project
from the front skirt.
So if the skirt's going like this,
do you want a long projection?
Do you want a short projection?
We chose about four inches
and we think it looks really good on the shadow lines,
but that's up to you to make that determination.
Don't overlook splicing the panels together
on the top main panel where you overlap them.
You don't want something
where it's gonna be flapping in the wind
or buzzing when the air is passing through it at high speed.
So pop rivet that all together along that overlap as well
to make one solid panel.
Now it's time to trim the overhang
on the sides of the awning.
And for that, we used an electric metal shear.
These can be rented.
You can also purchase them at,
if you're gonna do a one-time knockoff,
you can buy them as kind of like a one-time tool,
perhaps at Harbor Freight, something like that,
or perhaps you can rent them at a tool rental shop.
But these tools allow you to cut a straight line
for a long way because they nibble out a strip
down the middle and therefore you're not distorting
the metal as you're cutting through it.
It just removes that middle ribbon, as you can see here.
Trim everything to size and then trim the corners off
or round them off manually
so you don't have these sharp razor edges.
Any place you think you have a sharp edge,
take a file and hit them at a 45
to knock off any burrs or razors.
You want these to be hand-friendly as well.
Now, when you go to install these,
a quick trick is all the mounting bolts
are probably gonna be zinc.
So what we did is we simply screwed them
into a big block of styrofoam,
styrofoam insulation that's used on the siding of a building
and then we spray painted them all at once,
let them dry good and solid,
painted them from multi-direction
so you don't have any places that were missed.
But it makes it really fast
and you just handle them a couple times
and they're done and ready to install.
When it comes time to install them back in,
these types of awnings that we constructed
or had placed before use a triple bracket
along the top of the building that allows the awning
to simply be hung into place,
screwed in through that so they can't be lifted off
and then down on the side,
there's another bracket about two-fifths
down the side of the window
that holds the whole unit locked in.
Well, we've been very, very pleased with the results
and as I said, there's nothing like the sound of rainfall
and we've had some really high winds
where we've lived since installing them,
not had a noise, a creak, anything moving.
They're performing beautifully
and because they're metal
and painted with a great grade of paint,
they're gonna last for a long time.
We love how they look.
Well, if you like this kind of project,
I bet you're a gardener.
And if you are, check out this episode
of our do-it-yourself garden PVC drip irrigation system.
Low-tech, highly effective.
You'll love the results in your garden.
And while you're at it,
check out this other video we made for you
that YouTube thinks is just perfect.
How do they do?
Hey, until the next time,
this is Dirk Farmer Jay from DirkFarmerJay.com.