Today, on Workshop Edits, I'm building a storage bench for my newborn's nursery - super easy and functional for increasing sitting and storage in smaller nursery rooms!
📲 Check me out on SOCIAL MEDIA! INSTAGRAM: instagram.com/workshopedits FACEBOOK: facebook.com/workshopedits
Zach
In today's project I'm going to take you through how I built a bench for this little one's nursery.
Let's go ahead and get started. All right, so we are here in the shop. I got my plywood sheet behind
me. This is a relatively straightforward project. It's kind of just like a box with a bunch of
cubbies. So we're just going to begin breaking down all the material. We're going to use the
circular saw just to get started, make it a little bit more manageable for one person,
and then cut everything down to size on the table saw. Let's get started.
All right, so we just finished cutting the pieces. It's a little bit complicated when
you're just handling a big sheet of plywood and cutting big pieces by yourself. I'm also
not a very big person, I guess. All right, so the next thing we're doing now, we got six small
panels cut, which are going to be our vertical pieces, and we got the tops and bottoms cut here.
We're going to just use pocket holes to assemble this. This is going to be in a corner of the room,
and so you're really only ever going to see it from one side. So what I'm going to do is cut the
pocket holes and then position it so that all of them are facing away from when you enter the room.
So you'll be able to see them if you look really closely from the other way, but this way it just
looks nice and clean, and it's a really easy solution because it's just a functional storage
bench type thing. All right, so it is the next day. I had to stop working entirely yesterday
because I experienced my first true kickback. Long story short, I was cutting a spacer block,
which you can see here, and I'm going to use that spacer block to evenly space out the vertical
walls. I was pushing it. I must have been pushing it through slightly unevenly, and so as I was
pushing it kind of along the wall, it tended to want to get stuck, shoot across, and you can just
see it dug into this piece, and it threw it back at me at like 130, 140 miles per hour right into
my gut, and that was about like top two, top three most painful things of my life. I'm fine for the
most part. I have a huge cut, and it's bruised, and I'm going to have an imprint of plywood on
me probably for the next month. I feel good enough to start working, but man, that was scary, and it's
a good lesson reminder of safety. So I'm going to try to get back into it. We're just going to be
using the pocket hole screws to start attaching to each of these pieces that we have. I did cut
a spacer again to make them all even. We've got some stuff 3D printed in the background that I'll
talk about in a little bit, and then I'm just going to see how I feel and try to work through this
project without overdoing it. So yeah, everybody stay safe.
All right, so we just finished completing the carcass of this thing. Pretty straightforward.
Just wanted to make sure that all these were evenly spaced out. One like little quick tip for
using pocket holes is whenever you do it, you find that you line it up, and if you don't have it
clamped down, it shifts by like a millimeter, and it's really annoying. So what I found is
you just run a few pin nails or brad nails into it. It's going to lock that piece in place
temporarily with a little bit of glue. Then when you come back and add the pocket hole screws,
nothing's going to shift on you, and you end up with something that's nice and straight,
and you have nice 90-degree perpendicular angles. So now that that is done, we're going to do two
different things. So first, let's head over to the 3D printer. All right, so we're over at my
3D printer station. You've probably seen me use the Adventure 3 from FlashForge in some of my
build videos and on social media. I just got this Adventure 4 from FlashForge. They were cool enough
to send it to me. They're not paying me to say this. They're just like, hey, do you want to test
it out? We know you like 3D printing. So overall, I absolutely love this thing. If you are at all
interested in getting into 3D printing, I love this printer. This one is like twice as big.
It prints like 75% faster. It has a build area that's about three inches in every direction
bigger, which is awesome if you're trying to build things that are bigger than the
six-by-six-by-six platform. It's super quiet. It connects over Wi-Fi. It's enclosed. The enclosed
thing, I think, is huge for people who are in woodworking but want to get into 3D printing
because you can just see how much wood dust eventually gathers on this thing, and you don't
have to worry about the actual build area in here getting dirty. So my wife wanted this thing to be
super functional. She's like, I just want it to sit on the ground. I don't want it to have any legs
and just have this kind of overly modern feel. The nursery that we have doesn't have that.
I personally like to have my pieces sit just slightly off the ground. It just looks nicer,
in my opinion. So the compromise we came up with, or I came up with, was just printing these little
tiny feet. So again, I hopped into Blender. I prototyped some of these feet, and they're
going to work out perfectly because it's just going to give the bench this little kind of
floating look to it. You won't even really be able to see it, but I just think it's going to
look nicer, and that way you don't have just this big wooden carcass sitting on our wooden floor,
and that way if it gets moved around, you can put some furniture pads on the bottom,
and it's not going to ruin your floor. So compromise with the wife and a really fun
opportunity to use a brand new printer. I highly recommend this one. I'll leave a link to it in
the description if you're at all interested in learning more about it or just interested in
getting into 3D printing. So with that said, let's hop back over to the piece. So now that we have
these feet figured out, what I'm going to do is go back to the computer, drop eight of them into
the software for it, and print them. It's probably going to take like 12 hours just because I'm
printing them with PETG filament, which just prints at a higher temperature. It prints slower,
but it's stronger. It's going to look a little bit nicer. I have some white
filament, so again, it's like you're not going to be able to see them, but just aesthetically,
it's going to bring all this together. All right, so now that the feet are settled,
one other thing I want to do is add some hardwood edge banding to the front of this. So when you
walk into the room, the piece is going to be sitting up against this wall in this back corner.
So what I did was I angled all the pieces with the pocket holes facing this way, so when you walk
into the room, you're never going to see them. In hindsight, it was kind of dumb of me to
put this one facing inward. For some reason, I thought if I ever wanted to turn this around,
at least the outsides of it are clean, but that doesn't actually make any sense because then
you're going to see all the pocket holes from this way. So if you are rebuilding this, just
plan where it's going to be in your space and put it so all your pocket holes are facing another way.
Because it is going to be seen from this way, usually I like exposed plywood. I think it looks
really cool if done properly, but I don't know. I have maple. This is maple plywood or maple
veneer plywood. I just think it's going to look really nice if I do that. So we're going to head
over to the table saw, and we are going to do that. This plywood is half an inch thick or just
underneath it, so we're going to cut some strips that way, one for the top and bottom, and then
six of them to go across, and then just hold those in place with some glue and brad nails,
and I think it's going to look really, really good. We'll come back and fill in those holes
later with just a little bit of wood filler, and then sand this thing down,
and it'll be ready for finish. Let's do it. All right, so that wraps up the build part of this
thing. I'm really happy with how this came out. I know it's simple, but sometimes just simple and
clean looks really good. So the last thing we want to do is just try to match the aesthetic
of the wood a little bit to some of the furniture that's already in the nursery. So we painted
the dresser, which we got from Ikea, and then did some Ikea hacks to it,
this kind of off-white color. So we're going to whitewash some paint and paint down the plywood
of this. You'll still be able to see the grain through it, but I think it's going to look really
awesome. It's going to match the aesthetic of the room. My wife is going to do that, and while she
does that, I also just wanted to show you, these are the baskets that we got. We got these from
Ikea too. They're like a foot by foot by 13 inches tall, and we got five of them, and so those are
going to fit in between all the cubbies that we've done. And then just aesthetically, I think it's
going to look really awesome. So she's going to finish up painting, then we're going to call this
project wrapped up and get it in place. All right, so that is going to wrap it up for this project.
Hopefully you guys enjoyed it. Pretty simple and straightforward, but added a whole lot of
functionality and storage to this space. I also want to point out, it's been three weeks since
I had that kickback issue, and I am still recovering from it. So please, woodwork safely.
If you enjoyed the video, just let me know by hitting that like button.
Please be quiet, because this one's loud. I'll see you guys next time on whatever is the next one.
It's probably not going to be the next video. Bye.