My daughter's closet has slanted ceilings and is only 24" deep, so I'm building this drawer stack to utilize every inch of storage space. This project was possible with the help of my favorite paint brand & sponsor, Rustoleum, who is always coming out with the best products I can trust to give me a great finish.
Hey everyone, Melissa here. Lately I've been working on a custom storage solution
for a small closet I am creating for my daughter Lily's room. We live in a story and a half house
so there are slanted ceilings to work around. I'm going to show you how I built this slanted
storage solution you could apply to attics, under stairs, or anywhere that you have a slanted ceiling.
So now that you've seen I cut three-quarter inch plywood into the shape of my slant,
I'm planning out the rest of my cuts with a cut optimizer online. Go to opticutter.com.
It's so helpful to use your plywood sheets most efficiently while skipping the mental math. I'm
cutting up two sheets of half inch thick plywood to create drawers that pull out and utilize as
much space as possible. I prefer assembling drawers with a groove in the plywood for the
base to create a drawer box that is super strong, but I haven't yet bought a dado blade which would
make this faster. I simply set my table saw blade low and run each board through repeatedly to
create a groove wide enough that the plywood for the drawer bottom will fit, just like so.
The other pieces of plywood I cut were for the bottom and back side of my frame,
and these got pocket holes drilled so I could attach the frame box together.
Using corner clamps, I held my large plywood pieces tight while I screwed the bottom piece
on with kreg screws. Then I flipped it down and also screwed a back piece on. I'm not really going
to need a full top piece because the drawers will make some of that invisible when it's done,
but I do need to box in half of it. I'm creating a cubby at the top where building a drawer would
be so shallow, basically just screwing some three-quarter inch plywood in at the height I
want a shelf using pocket holes on the underside. For the top piece, I had to run the top and
bottom edges on my table saw at a bevel to match the angle of the box, and then screwed it in with
pocket holes the same way. Now it's looking so, so good. My frame is 40 inches deep, 24 inches wide,
and 51 inches tall. Next up, I'm going to build drawers that go all the way up this sucker,
providing an incredible amount of storage. Because these drawers are 37 inches deep,
each one will have a divider to add more functionality. The slides fully extend so
you can use all that space where the ceiling slant makes it difficult to access. I shared a detailed
version of how I build and install drawers you might want to watch next if you're going to
complete this project. I'll link it in the cards. If you're not following me on Instagram, you are
missing out. That's where I share stories every day behind the scenes of what I'm working on and
short form content that I usually don't repost to YouTube. Find me at welcome to the woods blog
and say hi. When building these drawers, using spacers makes everything so much easier. I actually
build the box as I go, measuring the distance between the drawer box sides when they're screwed
to the slide hardware before cutting the remaining pieces for my drawer box. Doing it this way means
I'm not trying to manage a big bulky box when installing the slides. This is especially handy
for building these very deep and large drawers. Most importantly, it ensures my slide hardware is
always perfectly placed. Originally, when I began building this, I planned to do full overlay
drawer fronts and skip the face frame. However, I've never tried inset drawers and I thought this
would be the perfect project to practice them. So I decided to build a skinny face frame that
would prevent me from having to move all my drawers I just finished further back. When gluing the frame,
I spread on a layer, then let it dry enough to get tacky, then spread a second layer to have
good adhesion. This is because when you're gluing the edge of plywood or the end grain of wood,
the glue gets absorbed quicker. Gluing twice ensures you have enough product to grab hold
even after some absorbs. I shot brad nails into the face frame to hold it tight while the glue dries.
So for the edge of the plywood on my drawer boxes, I didn't want to use edge banding because I thought
it would be a pain on such a skinny piece of half inch plywood. I devised a plan to water down wood
filler and smear it across the top edge to hide the plywood layers. When it dried, I sanded all
smooth with this speed sander and my favorite sandpaper. If my paper got a little gunked up
with wood filler, I cleared it off with my eraser stick. This was actually really fast,
cost effective, and it turned out so great. I will definitely do the wood filler trick again
for plywood edges. I did use some edge banding for the pieces of three quarter inch plywood that
make up the drawer fronts. Edge banding is so tedious, I do not enjoy it, but I do appreciate
how great the plywood looks like a solid piece of wood afterwards. You saw me cover plywood edges
with a face frame, wood filler, and edge banding. This project, I did it all. Now it's time for it
all to get primer. I always use Zinsser bin primer and recently I've been reaching for the shellac one
because it's the most versatile. It has the best stain blocking power, can adhere to even really
glossy surfaces like laminate IKEA furniture, and it has almost no odor. Before painting unfinished
surfaces like raw wood or fresh drywall, you always need to prime, even if you're using a
paint and primer in one product. That's just speaking from experience. Once the primer was
applied, I came in with spray paint. Rust-Oleum's 2X cover spray paint is the can I usually grab
off the shelf because it's the most affordable for the quality level. I get an even finish,
even when it's a glossy sheen like this, from the 2X cover, which applies a lot of product at once
compared to most spray cans, and I can spray at any angle, even upside down. You might be surprised
I'm using cans of spray paint instead of rolling on or loading up my paint sprayer. Here's the
reason. The shinier the sheen, the harder it is to get an even finish, so for gloss, spraying is best.
I like spray paint for its durability because it's oil-based, and I get that benefit here
without having to clean oil-based paint out of my sprayer, which is a huge pain. This whole project
only took me two cans of paint, so it was a total of like $12. After the paint had all dried, I was
ready to install the drawer fronts. I was nervous to do inset drawers because I've heard they're
tricky. You'll have to let me know in the end how you think I did. Have you built this style before?
I kind of just eyeballed the spacing with about an eighth of an inch gap around the whole drawer
front. Then I used my cabinet hardware jig to mount the poles. My Instagram audience voted on
which color and style hardware would look best. A five inch pole in champagne bronze. Here's how
my custom closet drawers turned out. I want to walk around 360, so don't judge my cluttered garage,
just so you can see how the drawers get shorter as they follow the slant.
The top drawer is 23 inches deep, the next 30 inches deep, and the bottom three are all 37
inches deep. Obviously, building this for your slanted space will need customized dimensions.
In the final installation spot, this will be sandwiched between two walls, and you won't see
any of these sides, only the front. You'll have to subscribe to my channel to see the closet space
when I'm all done. I love the combination of the warm, rosy color of the hardware next to the
almond paint color, and I am super proud of the smooth gloss finish in my first set of inset
drawers. The amount of functional storage this will add to a space where the ceiling slant prevents
you from easy access is astounding. Don't worry, I will anchor the frame box during install so it
doesn't tip forward when all these drawers are pulled out and full. I hope you were inspired by
my slanted storage solution, and that you will join me again for my next video on Welcome to the Woods.