Part 3 - Installing Windows, Doors, and Electrical - Building a Tiny Office

Workshop Edits
134 followers
76 Video Views·Jul 10, 2024
what's up guys I'm Zach and welcome back
to Workshop edits and welcome to episode
three of my tiny office build Series in
today's video we're going to be tackling
the installation of the window the door
and all of the interior and exterior
electrical of the
structure let's go ahead and get started
all right so we're going to move on to
installing Windows now I've never done
this before I've done a lot of research
on it I've watched a lot of videos I am
just going to follow the exact
instructions provided by
tyvec uh who makes a very similar type
of paper to this and just follow those
exact rules to make sure that the window
is installed properly it's level and
it's watertight first thing we're going
to do is cut out the window opening I'm
going to do it in the shape of an eye so
a cut at the top sill a cut at the
bottom sill and a cut down the middle so
I'm just going to find my
bottom actually let's do middle cut
first here's the top so we're going to
cut
all the way down
vertically going to put my ear
protection on I'm going to take these
flaps fold them back in just do a couple
of Staples
a few days ago when I was doing the
sheathing and I was cutting my window
openings I didn't do it exactly in line
with the overall window opening so I'm
going to grab my router in a flush trim
bit and just actually run it along at
least this top sill here just to fully
Shore up and have this sill be flush
with the sheating now that we have the
opening cut to the exact size that it
needs to be we're going to move on to
flashing so this is
6in Window and Door flashing tape I've
seen this done a bunch of different ways
the way that I'm going to do it is I'm
going to lay a strip that goes up about
6 in on each side and down across the
bottom of the sill it's going to cover
the inside here and wrap around to the
front and that creates a moisture
barrier for the window to sit on they
make rollers for pushing this down I've
seen people just use scrapers just to
really work it in and that seems to work
the best this stuff has a little bit of
Flex to it and it really seems to just
rub in really nicely with a with a
scraper kind of work it into all of the
wood grain into the corner and up the
edges and fold it over the edge and
that's going to create that watertight
seal so I'm going to start just kind
of working my
way help kind of feed it around this
corner do this one
first get that on there pull this one
over same with this side really pull it
down they do make specific tape that is
four corners it's like super expensive I
didn't buy it it didn't seem necessary
so I'm not doing it what did I just do
with my
scraper got my
window you're seeing me do this live I
hope it fits
heck
yeah cool looks
great I'm going to take it back out see
if it's level and see if we need to shim
it
up
wow that is perfectly level how about
that actually did something
right okay cool so I've got my window
laid down on the ground this is the top
side I am using white
dlex Superior flexibility crack prooof
seals joints for interior and exterior
sealant specifically for Windows Doors
siding and trim so in order to properly
seal a window you only put sealant on
the two sides and the top and the reason
you don't do the bottom is if there is
water or moisture that somehow does make
its way in it it's always going to run
to the bottom of the window and by not
having it sealed specifically with
window sealant that gives it a place for
the moisture to leave so we're just
going to run a thick beat of COA around
these three sides while my assistant Sun
bathes
all right so we just finished securing
the window got Nails in all four corners
and then either nails or screws every
other opening here thing feels very
secure and it is perfectly level so now
we are going to move on to just
waterproofing the rest of it so we're
going to do flashing on each side of the
window and then I saw two different ways
to do this one is to have your tyvec
tape actually fold over the window sill
and then to flash it or you just flash
it with this tape over the window sill
both seem to work perfectly fine so I'm
just doing that for
Simplicity and that should wrap it up so
we've got house wrap folded in
for the edges
here water sealed with flashing at the
bottom sealant caulk around three sides
open on the bottom to let moisture out
and then flashing tape added vertically
on the sides first to over drip the
bottom here and then on top to drip down
and out over the window or out and down
the sides here and I think we should
have a waterproof water sealed window my
first
[Music]
ever you what I love your bathing
suit some water
and uhhuh did you have a good nap and
swim you're going to swim yeah okay well
Daddy's going to finish doing this I'll
watch you swim okay
all right so just finished installing
the sliding glass door I installed it in
the exact same way that I installed my
windows so that included flashing at the
bottom then I cocked the three sides of
the door that weren't the bottom put it
in place and because the structure was
perfectly level and I've been checking
over and over again to make sure that
the walls are Plum I didn't have to do
any shimming with it it just sat in
dropped in really nicely and was already
perfectly level on the top and bottom
once that was pushed in I again secured
it with nails and screws around the
Border then I did flashing tape up both
sides flashing tape up at the bottom and
then you saw me also do one extra thing
which was cut these 45° angles in the
tyvec tape up here flip it up and then
drop it back down on top of the
underside flashing that I installed and
then did an extra row tape and that just
creates a redundancy overall to prevent
moisture from getting in again like it's
got this 20-in awning over it it's all
nice and seal off I don't expect there
to be any ISS ISU but again like I'd
rather just double up the redundancy to
prevent any issues down the road one
last thing I want to call out is just
when you're installing these sliding
doors the vertical pieces on the
outsides have some Flex to them so you
want to make sure that once you pop it
into place and you know that it's
sitting perfectly level and it's
adjusted to be in the center of where
you want it in your rough opening make
sure that when you secure these side
pieces to your wall with your nails or
your screws or a combination of both
that there's no bow to it so grab a
really long straight edge or a really
long level or just like anything that
you know is perfectly straight and
remove that Flex in the door and then
secure it in place I had to do that with
both sides of it it was something that I
actually forgot until I started doing I
was like wait this seems off so just
like take your time on that step and
that way you end up with a really nice
Square sliding door the doors slide
nicely uh screen door slides nicely and
overall like your installation goes
smoothly and that you don't have to go
back and undo work especially once you
have this flashing in place that's just
going to be a huge pain in the
butt doing things just a little bit out
of order but just because it just came
in I'm also just sealing off the bottom
of where the tape was meeting the
pressure treated boards with some like
flashing joist tape it's 6 in wide so
it's giv me a lot of play in terms of
how far down the tyvec went and then
tying it all the way into the joist so
overlapping the TYC the OSB and then
into the pressure treated wood and
because it's made for joist and flashing
it sticks to the wood really well it's
the next day and I'm going to switch to
focusing on all of the electrical
installation so I have my sub panel
hooked up it's a sub panel so the most
important thing to remember about that
is your neutral and your ground need to
be separate from each other that's not
the case on your main panel but it's a
very important thing to remember when
you are hooking up a sub panel I've
obviously had an electrician friend help
me with this part and like Consulting on
all that kind of stuff so just make sure
that you are fully understanding what
you're getting into with that kind of
stuff now that that's hooked up and the
breaker is off I'm going to start
putting in all of my Ruffins for
electric so that includes the
installation of all of the boxes running
all of the RX through the studs getting
the lights installed so I drew up this
really fancy grid of where I think I
want to lay out everything one thing
that I am doing is I'm doing 20 amp
breakers for everything in this I think
that is like both a California future
code thing as well as just sort of
future proofing this and I'm going to be
running two total Breakers one breaker
is going to take care of all of the
lights all of the like office based
electric stuff so like computer
Chargers um any of the kind of stuff
that you would plug in at a desk then
I'm going to have a separate 20 amp
breaker that will be fully dedicated to
just being able to power one window AC
unit during the hot parts of the year as
well as an exterior outlet that at some
point will run to a future sauna that we
plan to put in the back and that way
none of the electricity in here in terms
of what I need to actually like have a
functioning office for my computer setup
the lights working all that kind of
stuff is compromised when I know that
during like the hot months of July
August early September I'm going to be
wanting to run a small AC unit in here
pretty much full-time since I am not a
licensed electrician but I know what I'm
doing and this is like very basic
electric stuff I'm not going to go into
a huge amount of detail about exactly
what I'm doing but I'll just give a few
pieces of advice that I've learned along
the way first is that I know that you
need to have roic positioned at least 1
and 1/4 in deep into the studs and the
reason for that is if you are hanging
shelves or you're doing drywall you
don't want your Rox to be close enough
to the exterior of the walls so that you
might Nick it with a wire and damage
things so I came up with this little
spacing block just to make sure that I'm
drilling all of my holes far enough back
in the stud so that it's up to code I
also read a tip that your Hammer should
be roughly the height of any boxes that
you plan to run lower on the wall so
instead of having to like grab my hammer
every time I just made this little jig
that both will tell me the depth that I
need to have the RX run back into the
wall as well as the height of the bottom
of the box so that should make things a
lot easier too the last thing is that a
lot of people will say well you
definitely don't need 20 amps to run
lights a computer all that stuff like
it's probably not going to draw a Max of
like more than five amps at one time
with everything running one that's fine
the key is to make sure that you're
using a breaker that is 20 amps and RX
that can handle the right current as
well as having Outlet receptacles that
are rated for 20 amps so I have all of
those things the problem would be if you
had a 20 amp breaker and you were
running a smaller gauge wire like 142 RX
because what would happen is your
breaker would allow for more current
than that wire could ultimately take
that wire could heat up and that's what
ultimately leads to electrical fire so
as long as I'm using a breaker RX and
Outlets that match up with the 20 amp
breaker amperage that I'm going to be
using it won't be a problem because the
device devices that are plugged into
those things will only draw the amount
of current they need and the wire itself
and the breakers are going to be
outputting the aligned proper amount of
electric for it so I don't think this
process is going to be overly
complicated I'm going to start by
installing all of the boxes where they
need to go then I'm probably going to
Mark out where I want to install my
lights and get those roughed in and then
I'm just going to hook everything up I
this might take all day or this might
take two hours we'll just kind of get
going
I got this really sweet spade bit that
has this screw on the end this is a 3/4
in bit I kind of wish I bought a 1in one
but what it does is it grabs the wood
and it drills so quickly through I would
highly recommend spending like $8 on one
of these when you're doing any of this
electrical work all right so I got all
the boxes installed now I'm just going
to go and drill all of my holes out
across all of the studs to start just
feeding all the different rxs through
and sort of connecting the dots again
like I have a rough plan on paper and I
know ultimately what I'm aiming for but
I do not have like an exact process for
getting to that final solution so I'm
really just going to kind of do it as I
go and make sure and like double check
my work
right so that took all day I got almost
everything done so I'm just going to
take you around and show you the
electrical that I got done yesterday so
here's my panel it has two 20 amp
Breakers and the thing about this panel
is it's split so actually only three of
the circuits are hot and I happen to
have these double gang 20 amp Breakers
so this is the only one that's going to
be in use and this is the only one
that's going to be in use and I'm
actually going to add a 15 amp breaker
here for one more Outlet this 20 amp
breaker Powers this cable right here
which runs down into this box here that
forms a branch circuit one of them goes
all the way to these three light
switches CU I'm going to have three sets
of Lights in here these are the inside
lights there's going to be four 4-in can
lights these are going to be for two
more of those can lights outside that
are going to go underneath right
here and then the this one is going to
power a set of
sconces one of them is here and one of
them is here and they're going to be
facing outward and I'd ran out of RX but
obviously it's going to run up to
here and connect over to that one and
then for the can lights both of these
run up attached them to the studs and
then they run up through the roof and
the the lights are going to be installed
today I actually was able to mark those
out before it got too dark last night so
coming off that branch circuit we'll
have that outlet there one there one
there and then one all the way over here
so four total outlets and really low
voltage low power pulling LED lights
should be plenty on a 20 amp breaker the
other 20 amp one comes down
to this box right here which is actually
an outside facing one
that is on this side I have a gfic 20
amp receptacle on it and a
weatherproofing box that eventually is
going to power a sauna that I'm either
going to buy or build and put back here
for my wife that external facing
weatherproof gfic Outlet extends all the
way across that's what the extra row of
RX is over to that outlet there and the
whole point of doing a separate 20 amp
circuit specifically that could power
either the sauna or this Outlet over
here is so that during the hot months I
can plug in a window AC unit here have
that on its own breaker and not worry
about any of the other electronics that
are on a completely separate line being
tripped up you also might be asking why
did I use 12 gauge wiring for all this
won't that make it more difficult to fit
everything in boxes the answer is
because I already had it and yes it was
a lot more difficult to fit all that
especially in the triple gang outlet
that has three light dimmers last thing
I'm going to do is add one more 15 amp
breaker and it's going to power just one
Outlet up in this back corner and then
another one in this corner and the
reason is I eventually want to have a TV
in here and I want to have a dedicated
Outlet up there and it's going to be
easier just to have one single set of
extra Outlets run off its own breaker
versus trying to tie into these other
ones I can use 15 amps I can use 14
gauge Rox and it'll be a whole lot
easier so besides that last set of work
the last thing I need to
do so beside
so besides the last small set of
installations for those Outlets the one
thing I need to do is install an 8T
grounding rod to my electrical panel for
this build I've seen this done a bunch
of ways I'm just going to try the water
method where you just dump a little bit
of water in the hole and Shove It Down
manually and then keep repeating that
process and then I think for like the
last 6 to 12 Ines you probably need to
use like a 5 lb Sledgehammer but that
overall seems to be the most effective
method in doing this and I don't have a
hammer to do it anyway so I'm going to
do that really quickly tie that into the
electrical box finish the installations
and then we can move on to installing
the lights
I cannot believe how easy that was to
install that without a hammer drill I
don't understand water and fluid
dynamics but the water method literally
had me install by myself in under 4
minutes an 8ft grounding rod into the
ground the last thing I did before I
went to bed last night was Mark out
where my four can lights are going to go
in here so what I'm going to do is take
a small drill bit and drill a pilot hole
up through that way then I can take my
light template that these can lights
come with use that to Mark out the
circles that I'm going to need to cut in
the shiplap and I was strategic and I
made all of my can placements directly
in the middle of this 7in wide shiplap
because the hole I think I cut is only
like 4 and a/4 in so it's just going to
be a lot cleaner to cut that versus like
trying to do it across two pieces of
wood once I cut all four of those holes
I can drop in the can lights daisy chain
them all together and we can test this
thing out and hopefully finally have
power in here so that when it gets dark
I can keep working outside oh I'm also
going to use some 8 gauge copper wire to
tie the panel into the grounding
rod it was pretty unaware at how simple
they make recess lights these days
there's like a million options on Amazon
obviously at your big box stores but
it's super cool they come with you know
depending on what size you get this
light and they don't require an actual
can to put them in they're round recess
light so I guess they're not canned
lights they just have these tabs that
will uh pop into the hole that you cut
and then grip it in place they have this
plug on the end of them that plugs into
a junction box and the junction box it
comes with one of these for each one so
I got a pack of six so there's six of
these in the Box these cords attached
together and then screw into place so
you can't pull them apart and then these
boxes are awesome because they come
pre-wired with everything you need to
just make them very Plug and Play
especially with the connectors which is
amazing it makes it so straightforward
like anybody can do this and these are
cool because they both work on dimmers
which is why I installed dimmers and
they have five different temperatures so
the nice thing is the way I'm doing my
install is there's going to be this area
around that I cut where these are popped
into place and screwed into place and
then I can always why want to pull that
light down really easily and adjust the
temperature like this so it's really
early in the morning right now so I'm
not going to use the jigsaw to cut these
out instead what I'm going to do is get
all four of these boxes in place and
wired up to the RX that I ran up through
the roof from the dimmer switch then
once it gets a little bit later in the
day and everybody's awake I can make a
little bit of noise and cut these holes
out
all right here we go panel wired up
panel grounded
breaker
on wait look there on let's see if they
dim I did something right oh my gosh
it's perfect lights are done lights
inside are done oh I did
it all right so that is going to wrap it
up for this episode now if you are
watching these in real time make sure
that you are subscribed to the channel
so that you can be around and be
notified when the next video in this
series comes out if you are watching
these later on I will have a playlist
linked to every video that is launched
right here as well as the next episode
in the series right here if you have any
questions about this project materials
process some stumblings that I went
through or you just want to generally
understand where I got some of my
information from so that you can combine
it with this video and do your own
research please feel free to leave a
comment and like always I would be more
than happy to respond and give you as
much information as I can I'll see you
guys next time on whatever it is that
I'm building bye
