If your refrigerator door won’t stay closed, the fix may be a lot easier and less expensive than you think!
Of course, we’re assuming the problem with the door not closing is NOT related to so many items in your refrigerator that the door CAN’T close! And, the same goes for those “lurkers” that stand in front of the refrigerator for extended times with the door open!
Another potential problem is the door gasket has come out of its groove or is misshapen so that it doesn’t allow the door to close properly. If that is the case, you’ll need to clean out the groove and press the gasket back in all the way around the perimeter of the door. If the gasket is damaged, it can be removed and replaced, although that repair is not the subject of this episode.
HOWEVER, if your door, like ours, simply has gotten “lazy” over the years, and won’t close the last little bit on its own, then it’s HIGHLY likely the fix is quite easy and inexpensive.
In this episode, Dirtfarmer Jay shows you how to remove the door, replace a couple of small (but very important) parts, called door closer cams, and then reinstall the door. The parts are under $25 (including shipping), and can be ordered from www.searspartsdirect.com or www.ereplacementparts.com. While our refrigerator is a Kenmore® brand (made by Whirlpool®), this same part is used for several brands and models, so it’s a good chance this part may work for your situation.
This pair of parts are located around the lower door hinge pin. Our repair took under 20 minutes and required a ⅚” or 8mm nut driver or box end wrench, as well as a small straight screwdriver to pry out the worn part. The part number for the top half of the door cam set is WP2182179. The part number for the bottom half of the door cam set is WPW10329686.
These cams serve to have the door close in position so that the door gaskets seal and cold air is contained properly in the refrigerator compartment. We got 16 years of service from the door cams, so this inexpensive repair, using only a little time and a few tools, will probably serve us until it’s time to replace the whole refrigerator.
Sure, you can call an appliance repair service to fix your refrigerator door, but with your new-found expertise and a good parts source, you can JUST DO IT YOURSELF!
Follow us on Social Media to know when we’re building projects or releasing new episodes!
You can help support this channel by buying our merchandise or supporting us on Throne or Patreon Merch: COMING SOON! Patreon: https://www.patreon.com/dirtfarmerjay
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Do you have a refrigerator door
that just isn't quite closing anymore?
Well, if that's the situation you're facing,
I'm gonna show you three things to check
and a quick appliance repair
that'll take care of that dilemma.
Stay tuned.
Hey, Dirt Farmer Jay here from DirtFarmerJay.com.
Thanks for visiting us in this episode
where I'm gonna show you how to take care of the problem
of a refrigerator door that doesn't quite close.
Well, if you come around here,
you can see the refrigerator
that we've had for almost 16 years.
This dude has really served us well.
It's a Kenmore, which is made by Whirlpool,
but it's worked really well.
But recently, Dirt Farmer Maggie and I have noticed
that when you shut the door,
it just kind of stops like that.
Doesn't quite do the thunk that closes solid.
And there's been many times
her and I have come back to the door
knowing full well we've closed the door,
we nudged it shut, and it's sitting there like that.
Well, what gives?
Well, there's three possible things that are happening.
Let's look at them really quickly.
The first one is, please don't be insulted
because a lot of people have had this happen,
where there are items right in here
that are simply sticking out far enough
to stop the door from closing.
And sometimes it's not very apparent.
It may be where you put something in the back
and then you put a carton of eggs in the front
or one of those soft foam packs with meat or something,
and it happens to collide just right
with one of these types of liners.
We've cleaned this out for this video here
because we're going to show you
pulling this door off in a minute.
But that can be a problem where there's things here
and there that are just colliding.
So please don't be insulted.
Just check it and make sure that's not the problem.
The second issue that can happen
is the seal on the door itself
is a gasket that's right along here.
And this gasket sometimes starts to come out
and is therefore holding the door open
instead of doing exactly what it was designed to do,
and that is to seal the door up.
Now, if you notice here, this gasket is flexible.
And what's inside of here, right here,
is a thin magnet strip or ribbon
that is of medium strength.
And what this does is when you swing the door shut,
you can hear it grab at the last.
There it goes.
And that gives us nice seal.
And that magnet cannot be too strong
because if it was, every time you'd open the door,
it would try to pull the gasket out.
But you've got to check to make sure
the gasket has a nice, firm seat,
just like this, along the metal shell of the door,
and you don't have any gaps.
If you do, you'll need to pull that out, clean it out,
perhaps put a little WD-40 in it,
use a toothbrush or something to wash that out,
brush it out, and then reseat this back in.
There's one other thing I want to show you real quick,
just in case you may not think
there is a magnet in there, a ribbon,
is I'm going to take the high-strength magnet
I use for a stud finder,
and we're just going to put it there and see.
Do you get it?
Oh yeah, there you go.
So there is a ribbon that is in there,
but it's only moderate strength,
and that's what's providing that nice thunk
when you shut the door.
All right, let's suppose
that you've done both of those things
and you still have a problem
where the door is just kind of coming to there
and it won't quite close.
Well, you're going to need to do a just slight repair,
and this is a really easy repair,
but it takes just a couple of homeowner tools,
and I don't care if you're young, old, male, female,
you're handy or you're not.
This is a repair you can do.
Let me show you what you need.
Well, that's a pretty simple array of tools, isn't it?
First of all, you're going to need just a screwdriver
that you may need to pry a part out,
but you may not need this,
but I just like to have this on hand.
Then you're going to need a nut driver.
This is a 516s for our non-imperial friends,
metric friends on these refrigerators.
I found that a number eight millimeter works just fine.
And then I get an open-end wrench
or with a little ratchet end on it also.
So I have these two 516s.
You're going to need parts to fix.
And what are the parts?
Well, you can see what it's called right here.
Door cams or cams for the door.
What in the world are we talking about?
Well, in the lower corners of the doors
where the pivot is,
there's a set of cams that are interlocking
so that when the door gets closed to the closed position,
it kind of falls in and holds the door in its system.
Well, after 16 years of use,
ours is worn out as you can see in this picture.
Boy, they have just worn out over a period of time,
but this is what they look like when they're new.
So look at the cams there
and you can see they're nice and sharp
and they fit perfectly.
So when I put these together,
notice you get that nice, see there,
they want to fall back in, right back into shape.
And that's the action you need.
So you can get these
through appliance repair part distributors.
Many times there's bricks and mortar locations
in different cities, or you can go online
and there's a couple of places I like to go to,
ereplacementparts.com or Sears Direct.
I've got those both in the description below
and you can probably find your part.
And many times these parts,
this part fits over, I think,
40 different refrigerators I saw in the listing.
So a lot of these refrigerators are made by the same
or limited amount of manufacturers
and the parts are interchangeable.
All right, so what we're going to do now
is we're going to go ahead,
let me tell you what we're going to be doing
and then we're going to show it to you step-by-step.
First thing I'm going to do is take off the cosmetic cover
and the hinge cover at the top.
We're going to undo the hinge, lift the door off,
lay it on a packing blanket on the floor,
remove the cam that's on the bottom of that door,
replace it and put a new cam on the hinge pin
and then reverse, put the door back on,
put it there and it's a really simple thing.
We'll have this done in about 15 minutes.
So let's get to work and I'll show you how it's done.
Okay, so the first thing we need to do
is take off this cosmetic cover
and so you're going to need a nut driver.
It's a little tight, there it goes.
All right, and let's just go ahead and remove that out.
As you can see, really simple, that comes off
and here's the real workhorses right here.
These can be really tight.
Yep, all right.
Let's get a little helper on it.
I'm going to throw on one of these,
it gives me a little bit more lift.
There we go.
So I like to take off the back too.
You can do it whatever order you want.
Notice that I'm kind of holding the door
with my body over here.
So as we take these off, we're just going to go ahead and go.
Here we go.
All right, now that we have that,
we're going to go ahead and lift this out
and as you can see that hinge pin is what holds the door.
We'll just leave that right there and we'll go ahead.
The door is about ready to come off.
Okay, let's go ahead and take the door off.
You're just going to pull it back, lift up.
It's going to come out of the bottom pin
and when you do, here you have the whole door
and now you can see why we emptied this earlier before
and you can have this open.
If I wasn't explaining it, we would just go boom,
go very fast here, but the door is surprisingly light.
So if you're thinking, boy, this is going to be really hard,
not really, and there's good places to grip.
So what we're going to do now
is we're going to use a packing blanket on the floor here
because we want to keep everything in good condition
and we're going to lower the door down
and now we need to work on right here.
There's the cam and it's a little difficult to see,
but it is quite worn and if you look over here also,
that one is really worn as well.
So both these need to come off and be replaced.
So what we're going to do is go ahead,
take our nut driver, pull this out.
As you can see, it's simply one nut.
This is where that flat screwdriver can come in handy
to kind of get into it a little bit.
There it comes.
Notice you just pull out the piece.
There it is.
We're going to take our new one, put it in, in its place,
push all the way in,
replace the nut here or the screw,
seat that in nicely.
Don't over tighten, but just make sure it's good and snug.
We're now done with the door portion.
Let's go ahead and repair this part over here.
So we're simply going to remove the worn door cam here
and notice now you have the metal hinge pin right there.
We're simply going to put this back.
Rotate it around into the right position there.
Replace.
Again, nice and snug.
These are self-lubricating.
If you want, you could put a little bit of like
lithium grease or something like that on that.
But if you look close, you can see these are,
this is quite worn.
And it should be after 16 years of active family life.
I'd say it did a good job here.
And these parts only cost somewhere around $6 each.
Okay, let's go and put the door back on.
You're going to have to finesse this a little bit
to get it where it needs to go.
There it is right there.
Go ahead and swing the door in place.
I could feel the magnetics grab right away
and the door will stay there long enough
for me to put the top on.
All right, let's go ahead and put the top together.
All right, we can go ahead and reline here.
If there's not sufficient grease on here,
you can put a little bit of grease on this.
We're simply going to put it back in
and we'll lift it slightly to get around that nut.
And then I'll line the door back up.
We'll just reverse steps here.
I'm going to go ahead and start all these.
You may have to wiggle the door a little bit like this
to align, and that's perfectly normal.
Let's go ahead and nut driver all these down.
Make sure you don't tighten any one of them
all the way home initially.
Just get them all ready to snug down.
All right, now one last thing to do
is to just look and make sure the door,
the gap along here looks good.
And it does.
When I did that, I have a nice line,
which you can't see from that angle.
You'll have to trust me.
There we go.
We're going to go ahead and drive these home now.
And I'm just going to put a little bit of wrench pressure.
I don't want to over tighten too much,
but I'm just going to,
that helps me to make sure they're good and snug.
There, that one benefited.
All right, now the cover goes back on.
All right, let's take a look
and see if we have fixed our problem.
Okay, let's see if what we did works.
Okay, so I'm going to take this.
I'm just going to slowly close it.
Look at that.
Closes right up.
And those cams now take care of that.
Wow.
If you found this video to be helpful,
won't you like it?
And better yet,
please subscribe to our channel.
And when you do,
please ring the bell
because then you'll get notified
approximately every Friday
when a new episode comes out
about Maggie's Kitchen,
truck life,
product reviews,
homeowner skills,
shop life,
and all sorts of fun stuff
where you just do it yourself.
Until the next time,
this is Dirt Farmer Jay
from DirtFarmerJay.com.