So one of the best things and maybe one of the most daunting things about moving
into my own space was just figuring out how I was going to organize it.
About six weeks ago, I bought my first real big tool purchase, which was a saw stop contractor's
saw. And needless to say, right after I bought it, I quickly realized how badly I needed a really big
outfeed slash assembly table. Now, I did a ton of research about what would work best for my
shop based on the size of it. My space is about 19 by 19 feet, so I needed something that was
big enough to handle me working with giant sheet goods in case I wanted to build something big,
but also something not so big that it overtook my entire space. So I ended up with a table that
was four feet by five feet, and I think it is just under 34 inches tall, which is the height of my
saw. And it has a top really large work surface as well as a bottom storage shelf that can be built
out later depending on what kind of needs I will have down the road. So the entire project is made
out of three sheets of three quarter inch plywood, and I designed it specifically so that I only
needed that much material. Step one was just breaking down the sheets into manageable sizes,
and using rigid foam insulation as a cutting surface is one of the more underrated and cheap
Home Depot hacks that you should quickly adopt as a maker. And as I broke down my material,
I was careful to label each piece as to not mix things up. Each of my legs was going to be created
using three inch wide strips butt jointed together, and the key was to rip them all to their final
width on the table saw, and then gang cut them on the miter saw so that they were all the exact same
length. I also ripped a few pieces on the saw that had 45 degree miters on them, and these would add
shearing strength to the build, and you'll see what I'm talking about later. Everything on this
build is assembled with glue and one and a quarter inch pocket hole screws. The screws are for initial
strength, and the glue will give this build a long lifespan in my shop. So after making my four legs,
I could attach everything with stretchers using glue and screws again, and I repeated this for
both sides of the table. Next was much of the same thing, attaching the next set of stretchers on the
bottom ahead of bringing all four legs together at the base. Now before moving any further, I added
those corner supports which really increased the shearing strength of the table, and before final
attachment I added two stretchers across the bottom to help support that bottom shelf. So then I could
combine everything together. Next up was attaching the bottom shelf which I first glued on, and of
course I brought in some higher help for this. Finish nails held this thing in place while the
glue cured. The top went together much like the bottom did using corner supports for rigidity,
and the middle supports to support the larger top that I would go back and add at the end.
Once everything was connected, I could take my tabletop cuts and lay them on the table for final
positioning. Now to get everything squared up, I clamped both pieces in place and then left one in
place, glued up the other piece, held it down with finish nails, and then repeated that process for
the other cut. So since I wanted this thing to be really heavy, it's pretty heavy. My plan called for
having a dual stacked top, meaning that I would have one sheet of plywood actually attached to the
base of this thing, and then another sheet on top that would only be held in place with finish nails.
That way if it got too dinged up over time just from wear and tear, I could pull it off and replace
it with a new piece of wood. Last up was to add miter slots to the side of the table that touched
the table saw. To make sure the table was square, I used a speed square and then traced a line from
the edge of the table, and then ran the square along the table saw edge to make sure my measurement
always stayed on that line. Then after a few measurements and setting the final depth of my
router, I routed out the two grooves. And I think I did two passes with a one inch dado bit to actually
cut that slot. So like I said before, I don't have exact measurements for this table. It is four feet
by five feet. It is just under 34 inches tall, and it has two shelves. It's built from three sheets of
three quarter inch plywood. I think the important thing for these videos in terms of shop furniture
is not so much to try to replicate exactly what you see somebody build, but instead do lots of
research and pull lots of inspiration to figure out what is going to work best for your space.
So with that said, I really encourage you to check out all the videos online that have shop furniture
projects that you're interested in doing, especially the ones that I posted below so you could see where
I pulled the design inspiration from because they were super useful to me in trying to figure out
how I want to build out my space. So I think that's going to wrap it up for this video. If you did
enjoy it, I welcome you to subscribe to the channel. If you did like the video, I welcome
you to subscribe to the channel. Hopefully you'll be seeing tons of projects coming out of this shop
down the road. It would be awesome if you guys stuck around for it. So thanks again for watching
and I'll see you next time.