Part 4 - Roofing, Fascia, Shiplap Ceiling, Insulation - Building a Tiny Office

Workshop Edits
134 followers
153 Video Views·Jul 17, 2024
what's up guys I'm Zach and welcome back
to Workshop edits and welcome to episode
four of my tiny office build Series in
today's video we are going to be
tackling the entire roof the facial
boards as well as the underside shiplap
ceiling of this
structure I hope you guys enjoy it let's
go ahead and get started I'm up here on
the roof it's a beautiful day I'm going
to get my rigid foam insulation done on
the roof it's almost the exact perfect
size just to have three of these sheets
of 4x8 1in thick rigid foam the only
thing I have to do is cut around where
my light placements are and then I can
drop them into place and I'm going to
attach them using
these fast and tight screws you can see
them they have like a plastic cap on
them they'll drive through the foam but
won't go through it because of that
plastic cap and they'll go into the roof
below it then when I actually put the
OSB on top of it I'll drive screws that
go all the way through the insulation
through the roof into the rafters
[Applause]
[Music]
getting the OSB secured to the roof on
top of the rigid insulation that I laid
down the other day I'm using the
perimeter to secure the wood and like
make sure that it's straight the roof is
actually very very Square so that's
helpful then I'm also using these big
4in screws that I already had to drive
through the plywood through the uh insul
insation through the shiplap roofing and
into the actual studs underneath so
that's pulling everything down and
securing that OSB before we move on to
felt paper and actually tiling the roof
and doing like the rest of the finishing
up
here for
all right just finished so many things
so I wanted to tackle the entirety of
the roof in order to start that I needed
to paint all of my facial boards I need
to get my facial boards hung up and then
paint them so I ended up doing two coats
of this black color called Tom Cat it's
a matte color it looks freaking
awesome once the paint was dried I went
on and and I sealed all of my edges and
all of my joints in the OSB and up to
and around the facial
boards then I can move on to flashing so
I did the rear flashing first with
roofing nails over the edge to 2in drip
edge and I'm using black flashing to
match the black trim
then I did the
sides ow
I smashed the out of my thumb so
that felt great then I moved on to
Roofing paper so I wanted to do the rear
and side flashing first so that then the
roofing paper could layer on top of it
so there's a bunch of redundancies in
the overall like moisture protection of
the roof I'll have the OSB then with the
sealed edges then with the drip edge
over those edges and they're also sealed
with like Roofing sealant CA type stuff
then the roofing paper with plastic cap
nails is over those edges so a third
redundancy now the last thing to do is
the shingles so it's about 12 by 8 so
it's about 100 square ft of roofing
shingles and I'm just going to go one
row at a time staggering them as I go
per the recommended instructions doing
it all by hand don't have a roofing
nailer but I don't know it's kind of
nice to just swing a hammer and get
better at it so I don't smash my thumb
in the
future the other thing I did was preut
my side pieces I'm sure there's a term
for it uh there's a really
straightforward method to following to
cutting these and allows you to have the
least amount of waste with the shingles
that you buy so you start by using a
full strip then you take another strip
you measure 10 and 38 in in and you cut
that in half you end up with two pieces
then you take another piece you measure
in 16 and 38 in and you cut it down
there and you end up with five pieces
that are stacked quite evenly and you
just repeat that fstep pattern so that
your shingles are offset and you don't
have seams that end up on top of each
other well annoyingly I ran out of tiles
but I got really far so I just got to
finish
up that back corner over there but
overall it's looking really nice finish
up the top put the drip edge on and this
roof will be finished
all right fast forwarding the roof is
done so my neighbor happened to be
redoing his roof with the exact same
black shingles that I was using so he
was cool enough to give me five of them
so I finished up this back corner and
you saw me cutting and cornering the 2in
drip edge for both of the fronts so
those went on last over the top so that
water will run either in front of it and
then down the facial boards or it will
run down the roof and and then over the
first double layered set of shingles so
those were hammered down with Roofing
Hils and then I went back with my
Roofing seal and I sealed each one of
those Nails the flashing I feel really
good about this I'm really excited to
not have to get up on that roof anymore
because it is 100% complete so my plan
for the underside of the overhang is to
do a painted ship lap it'll be the same
color as the facial board so that like
nice matte black so I started off this
morning by painting everything like
doing a a first layer of paint on it
just figur it' be a lot easier to paint
things on the ground versus getting
everything up and trying to do multiple
coats of
paint doing this totally solo so the
hardest part is definitely hanging these
12T long pieces luckily I have two
ladders so I'm just going slowly lifting
them both up on top of the ladders and
then trying to just push and add some
brad nails as I go and as I go things
start to secure in place and just making
sure they're properly cut to length for
the middle of the long pieces that is
where I'm going to have my two recess
lights that will sit on the underside
they're the same ones that are on the
inside I just got two of them out here
on a separate switch so I marked and
measured out evenly inwards once I had
that piece cut to length used the same
template and cut it out with a jigsaw
the third piece is a little bit tricky
because it overlaps the corner so what I
had to do is measure the width from the
like remaining amount of space in
between and then I used my circular saw
to cut the very like small sharp corners
and then I did a two-part cut on my
table saw where I marked out what I
needed to do set the fence to that exact
width and then I raised the blade up in
it did a pass one way turned the saw off
lowered the blade flipped the piece over
and then ran the saw the other way and
that way I had a really nice straight
clean
cut just got that piece hung and I'm
really really impressed with how well
that came out like measuring three times
cutting twice Vibes now that I have all
that done I'm going to move on I'm going
to cut all of my 8ft pieces to account
for the side that should go really quick
cuz it's just brad nails in each of the
two places where I put wood to attach
them to running all the way down then
we're going to have to cut a couple
pieces to go the length just one piece
to go the length of the rear
side got all the boards installed I'm
going to go around and use some silicone
and seal up all of the nail holes let it
dry and then give it one more coat of
paint and that's going to be done looks
awesome
now that the entire roof is done all of
the electrical is done the sof is done I
really can turn my attention to two
different things one the outside facade
or to the inside insulation and
drywalling I'm probably going to go back
and forth between them just based on how
much I probably am going to hate
drywalling but it's really nice out
right now I don't have any of the
exterior materials I don't have the
drywall yet but I do have the fiberglass
insulation I do have the spray foam
insulation for all the corners so just
going to spend a little time going
around to all of the corners and all the
bases and like any of the exterior
outlets and do the spray foaming then I
think we're going to spend some time in
the evening doing all of the fiberglass
insulation so that then I can actually
get the materials for drywalling and
have a blast doing that
best part about having the electrical
done means I can work at night so I have
a beer I have music and I have
insulation so I'm going to work for
however long it takes but I'm going to
try to get all the insulation done few
tips that I read and they're specific to
working in California one is have the
moisture barrier facing the inside I
don't know why but I think because it's
generally just just hot and we're trying
to keep our places air conditioned it
helps to have the moisture barrier
facing inside the other thing I read was
that when you get to wires ideally you
will split the fiber glass insulation in
half and go half on one side and half on
the other and that way you don't press
the insulation up against a wall on the
exterior or the interior and it's like
split nicely the other tip I read is
that you use your studs as your like
backer to cut a straight line and try to
use a straight edge if you you can just
to make your Cuts nice and clean and the
last tip I read was fill every space
possible so that means like cutting
small things trying to fill the space
behind Outlet so like I've never done
insulation before so I'm just going to
start with one wall figure it out as I
go and follow all the rules that I read
this should be like a really enjoyable
evening
I guess one of the benefits of having an
OSB flooring is it can basically be my
cutting board
so this is what I was talking about I've
got RX wire up here you can
essentially split this I'm going to go
put a mask on after this I'm going to
feed this underneath
right
I'm so
itchy but I am
done all right so that is going to wrap
it up for this episode now if you are
watching these in real time make sure
that you are subscribed to the channel
so that you can be around and be
notified when the next video in this
series comes out if you are watching
these later on I will have a playlist
linked to every video that is launched
right here as well as the next episode
in the series right here if you have any
questions about this project materials
process some stumblings that I went
through or you just want to generally
understand where I got some of my
information from so that you can combine
it with this video and do your own
research please feel free to leave a
comment and like always I would be more
than happy to respond and give you as
much information as I can I'll see you
guys next time on whatever it is that
I'm building bye
