25. Throwing / Making Mugs & Pulling / Attaching Handles with Hsin-Chuen Lin 林新春 馬克杯拉坯修坯接把示範

Hsinchuen Lin
205 followers
81 Video Views·Oct 12, 2010
To see or buy my finished work and pottery tools, please visit my ETSY shop:
http://www.etsy.com/shop/hsintools
http://www.etsy.com/shop/hsinchuen
To watch more of my throwing videos, please visit my channel:
http://www.youtube.com/user/hsinchuen
Visit my Website: www.mypots.net
Follow me on Instagram: hsinchuenlin
Like me on Facebook: Hsin-Chuen Lin ceramics
My mugs, I usually like to pour the handle first
so that
The handle will be dry in time when I'm attaching it. It's easier for me to handle
I usually attach my handle right after I
Trim my pot, but I pour my handle maybe an hour or two before
So that it the surface is dry. It's easy for me to handle
Now I'm going to show you how I pour the handle. First, get a piece of clay like this size and
then you
You roll it
Okay, and now you
pound it
Flatten it a little bit
So that you can see that this is almost the shape of the handle
When you are pulling the handle, you want to have lots of water so that it doesn't break
When you are pulling it
This is my hand. You want to wet your hand and also wet your clay a lot
Try to form your hand like this
So that the clay is passing through here
from this opening
lots of water
Because your hand is
Irregular shape so one side might be more angled than the other
So when you're pulling it, you want to switch sides
So that it's more even
And when you are pulling it, you want to pull it down all the way
You don't want to stop right in the middle
Otherwise the bottom part will get thicker and it's easier for you to break it
So make sure you pull it down all the way
You can see that I keep constantly switch
alternate on both sides
Okay, once you have your shape nicely
I usually put my
This forefinger on the back and then using my thumb to make a little indent
So I'm pulling it down like this and then I'm doing the other side
One, two, one, two
So that after I'm done
The both end of the handle looks a little bit thinner
I like that way
Some people do make an indent right in the middle. So the both end will be thicker. It's a personal preference
I like the both end a little bit thinner. So so that it looks more that the handle looks more elegant
After I done pulling it, I just hang it right by my wheel. You can see six handles right hanging by my wheel
This is where I'm going to attach my handle and then a little bit of slip here
As I told you I pull the handle
about
One hour or two before I attach it. So now the handle is
It's a hotter a little bit, but still
Soft enough that you can move it around
But the surface has been dry so you don't have a finger mark here
so
I'm probably using this part
so first
I will cut a little curve here
And this is the handle I'm going to attach
Let's go here
Before I add a slip to it
There's a little
Tip that I would like to show you. I usually use my fingernail to tap it so that it opens a little bit
It's like a mushroom. I
Use my finger to tap it
then I
slip over
And I attach to it
With one of your finger holding on the back of the cup. You want to squeeze it
So this is the attach process
Usually after I attach it. I don't
Work on it right away. I let it sit about
five to ten minutes so that the water will draw from
your cup
The cup will draw the water from your handle so that the both
are at the same dryness stage
So I will let it sit here and then
Let it sit
Okay, now it's almost
Five minutes, so I'll show you how I attach and finish
As you can see that
Already attached and you can see my handle can stand up because it's harder a little bit
now I'm using a needle tool to
smooth the joint
I show you that I tap it so you can see that the
On the edge of the handle. There's a little bit extra clay that you can use the clay to
smooth it easier
Okay
The top already joined and it looks good
Now I'm going to hang it and attach to the bottom here
Maybe I will give it a little bit of slip
on the bottom part here
All right
before I
Attach it. I like to because of my finger mark. I like to smooth a little bit so
I use my finger to smooth the joint a little bit add a little bit of water here and then
Very lightly pull the handle a little bit
Keep the handle a little bit of moisture. So when you hang up and
Hang it down it create a nice curve
So just let it hang in
Naturally like this
Good adjust the curve a little bit
Okay, cut the excess clay off
Okay before I
apply pressure
The final step is I get a little bit of water and just drip it here
so that you have moisture and then you just use your thumb or your other fingers to
Compress to push down
And just blend it
So this is the mark I
add
