Fixing a Vauxhall Vivaro P0201-13 Injector Circuit Fault: Step-by-Step Guide
Recently, a Vivaro came in with injector-related fault codes that had been persistent, despite the injectors being replaced. Below is a full breakdown of how the issue was diagnosed and resolved, step by step.
Understanding the Fault Codes
The main fault code we tackled was P0201-13, which refers to an injector circuit open on cylinder one. Additionally, there were related codes for cylinders two, three, and four:
* P0202 – Cylinder 2 Injector Circuit Open * P0203 – Cylinder 3 Injector Circuit Open * P0204 – Cylinder 4 Injector Circuit Open
This indicated a widespread injector issue. Despite having new injectors installed, the customer was still seeing these errors—and even worse, the van wasn’t running properly.
Symptoms the customer reported:
* Jerking and misfiring when accelerating uphill or under load * No issues during steady cruising
Two separate garages had already suggested replacing the injectors again, but something didn’t add up. A deeper inspection revealed the real culprit: corroded or poorly connected wiring to the injectors.
Accessing the Injectors
To repair the problem, the first step was getting to the injector connectors. Here’s how we did it:
1. Remove the air intake pipe – This provides initial access to the area. 2. Pull the wiring loom out of its housing – Carefully disconnect anything in the way, such as vacuum lines or other cables. 3. Unclip and remove additional parts – Items such as the oil feed line and other wires may need detaching for better access.
Once everything’s clear, you’ll see the glow plug connectors and injector connections.
Inspecting and Cleaning the Connectors
The goal here was to improve the electrical connection. On inspection, one injector connector had visible darkened corrosion on the terminal—a clear sign of trouble.
Here’s what we did:
* Tightened the contacts: Using small picks, we carefully adjusted the connector terminals to close the gaps. This ensures a snugger fit onto the injectors. * Scraped away corrosion: A pick was also used to clean up any built-up grime or rust. * Used contact cleaner: A few sprays of fast-drying electrical contact cleaner helped improve conductivity.
We made sure to repeat this process for all four injectors, even if the others didn’t show obvious signs of damage. When it comes to connectors, it’s better to treat them all at once—it saves you trouble down the line.
Clearing the Upstream Pressure Pipe
While working on the engine, we also took the opportunity to clear the DPF upstream pressure pipe. Using a 12-inch cable and some DPF cleaner, we cleaned out any potential blockages. This step helps prevent clogging in the diesel particulate filter, which can trigger related warnings.
Pro tip: Be careful not to overload the system with DPF cleaner; a little goes a long way.
Putting It Back Together
After finishing the injector connector clean-up and pipe clearing, we reassembled everything:
* Reconnected all the wiring * Put the intake pipe back in place * Double-checked each component for a solid fit
Now it was time to start the engine and see how things looked.
The Results
As soon as the engine was running, there was some good news—the warning lights had disappeared. Without clearing the fault codes manually, the system recognised that the injectors were functioning properly again.
Using a diagnostic scanner, we confirmed that the injector-related codes were no longer active. Only a minor issue related to the battery current sensor lingered, which is common on these vehicles and unrelated to the injector fault.
A test drive followed to make sure the issue was resolved. The Vivaro performed smoothly, both at steady speeds and under hard acceleration. The jerking and misfiring were gone, and there were no faults on a final scan.
What Was the Real Problem?
Despite initial assumptions, the injectors themselves were fine. The root cause was worn or corroded connector terminals, which prevented proper communication between the injectors and the ECU. Cleaning and tightening the terminals was enough to fix the problem, proving that costly injector replacements weren’t needed at all.
Final Thoughts
If you’re dealing with injector circuit faults on a Vauxhall Vivaro, Renault Trafic, or similar vehicle, don’t rush to replace components based on fault codes alone. Corroded connectors are a common issue and are often the cheapest and quickest fix.
This quick repair saved the customer significant time and money—and more importantly, got their van back on the road without any hassle.
Got similar issues with your vehicle? Let us know in the comments or reach out for advice. See you in the next how-to!
Hello, it's Jimmy here at Eberlees and I have here to look at a Vauxhall Vivaro.
It's got a check injection, check anti-pollution system error.
So this is the fault that we're looking at, check anti-pollution system.
Obviously on these you can get check and injection and engine failure hazard as well.
That's the one that we've got coming up in a minute but the customer has been clearing fault codes before he made his journey down here.
OK, so this is the fault code that we're looking at. It's a 020113 or a P020113.
There was also P0202, P0203, P0204.
So cylinder 1, 2, 3, 4. Cylinders 1 to 4 basically.
Injector circuit open. It's had the injectors replaced but a fault has come back.
It's brought it back to that garage and another garage and they both just offered to replace the injectors again.
So it's a very common issue with these that I see that the fault is not actually with the injectors, it's with the connectors to that.
So we're going to start removing some of the bits and pieces and we'll get in and show you.
OK, so first just remove the air intake pipe.
We're just now pulling up this wiring loom away from the case.
We've got a vacuum line here.
Some more wires that we just need to pull out along there.
A bottle here. Just going to bang it to the side.
Take that out and we'll disconnect this oil feed or whatever you call it.
A couple of 10mm bolts going across. One down the back over there.
Then we've got these two clips on the front. Once you've got all those out you can remove that.
Then we have access to the glow plug connectors here.
So I can see that this one has a darkened terminal on the left side.
So it's got some sort of corrosion on it.
OK, so what I'm doing here is I'm just sandwiching the terminals together using two picks.
And if we pull those out you can see that we've closed the gap together a bit.
And I've obviously used a pick to get in the middle and just give it a scrape up so we've got a good connection.
And then we'll also use some electrical contact cleaner.
This is the one I've got today. Obviously it can be any sort of brand.
Fast drying contact cleaner for electrical terminals.
So you just give it a little spray up.
They do all four.
So what I'm going to do here is just get these little pins as well and just bend them upwards slightly.
It's going to help with the connection.
Now we've done all of the injectors we move on to the next bit which is feeding our little cable down here.
And we're just unblocking the upstream pressure pipe that's over here.
Now we're all the way through with that.
We get asked the question a lot, how long is that piece of cable that I'm using?
So it stops there about a foot long, 12 inches long, something like that.
Maybe a bit longer.
Just getting some DKF cleaner through the pipe.
Only little amounts. Obviously it will be pulled.
Some of it will be pulled through the engine so you've just got to be careful you don't overload it.
OK so that's everything put back together.
We've had the engine running for a couple of minutes.
Now if we get back inside, surprisingly the warning lights have gone out.
I haven't cleared the codes.
So we're going to get the diagnostic machine back on.
We'll have a look. We should still have the codes here.
There we go.
Obviously we've had the upstream pressure sensor one now as well because we've had that disconnected.
So the fault lights have gone away.
Which would suggest to me that the vehicle now knows that the injector is working correctly.
But we just have to now clear the fault log.
There are some other fault codes here.
Invalid multiplex systems.
I'm going to put that down to this one. Battery current sensor.
On the negative terminal of the battery. It's quite common on these.
So now I'm just going to turn the engine off.
We'll clear all of these lights.
Take the vehicle on a test drive and then re-scan it to see what fault codes have cleared or which ones have reappeared.
Okay, we've done a test drive. Now we're just waiting for a re-scan.
Going to see what fault codes. I'm pretty sure nothing is going to come back up.
We'll just give it a scan and make sure that everything is coming up clear.
See what's gone so far. Have we done the engine?
Yep, engine code is clear.
And I will tell you what the customer was having issues with here.
So he was having issues where if you put your foot down, if you were cruising at an average speed it was fine.
But if you tried to accelerate, especially if you were going uphill, the more you put your foot down the van would jerk and misfire.
And that's the issue he was having.
So I've just taken it on a test drive. I've driven it smooth and I've driven it with some hard acceleration.
And we haven't had any of those issues return.
The really good sign for me was that the engine light distinguished on its own.
So I didn't have to clear any fault codes.
Which is a big confirmation that something has changed.
Okay, so that's it. We're all sorted on the Vauxhall Vivaro for Renault Traffic.
And I'll see you on the next video.