How I built a sliding barn door console table with hidden TV lift. This is a perfect solution to hiding that ugly side view of my TV mounted on the wall. The center cabinet is ½ depth and great for holding home décor. Slide the barn doors to reveal full depth storage for media supplies, DVDs, etc. With a click of a button, a TV magically lifts from the back of the center cabinet using the TVLiftCabinet mechanism.
I have swapped a TV mounted on my wall for a new sliding barn door console table with X detail.
The center cabinet is great for displaying cute knickknacks.
Slide the doors to reveal a deeper storage space,
but it holds a secret. A quick click of the remote control, then up comes the hidden TV.
I built the cabinet in three sections. Overall, it's quite large at seven and a half feet long.
The outer cabinets are full depth. The center cabinet is about half depth.
With the current price of pine being super high, I decided to use knotty alder to build the console
table. I ran the rough boards through the planer, then cut the boards down to the widths needed for
the console table. I used face frames as the backbone of these cabinets, so first I glued up
all the face frames needed for the console table. The center cabinet has one face frame,
but the end cabinets has a face frame on the front and then
two side face frames. To reinforce the face frames, I used wood biscuits and a biscuit
joiner to make the cuts. Dowels or pocket holes are alternate methods that work good.
I glued up the face frames and used Bessie parallel clamps to hold tight until the glue
dried. But first, I made sure that the face frames were going to dry square. You do this
by measuring diagonally corner to corner and the opposite diagonal. If the face frame is square,
the numbers will be the same. To create character on the end cabinet sides, I routed a tiny chamfer
on the side slats. The side panels are made up of these side slats that are glued to the face frame.
The slats are inset a quarter of an inch, which will mate with the front face frame dado during
assembly. On the two inch side of the face frame, I marked a quarter inch reference line,
then I glued and secured the side slats with one and a quarter inch brad nails.
Now time to add the X detail. I should have used the face frame and marked the X pieces before
gluing the side slats on. Oh well. I marked the center of the X pieces and lined that up with
the side panel. Then use a square and line that up with the face frame boards to mark where to cut.
Repeat that method for both ends, then trace it onto another board. Cut out the center section
of one of the boards to make the X. Finally, glue and secure the X detail in place. I decided to
assemble these cabinets with dados. Each face frame, side panel, and divider get a three quarter
inch dado about four inches up from the bottom. The front face frames need a dado on each style
edge. That's the vertical edge. The side panels must be mirror image of each other. They need
a dado for the divider panel about eight and three quarters of an inch from the front edge.
I decided to add holes for adjustable shelves. This is easiest to do before the cabinet is
assembled. Time to assemble the cabinet bodies. Dados can be super nice during assembly when
everything fits together like a perfect puzzle. Clamps are needed to hold everything in place
while the glue dries. This method makes a really nice strong cabinet. It can also be frustrating if
you messed something up, so a dry fit before glue is essential. Make sure to check for squareness
while you're clamping the cabinets together. On my end cabinet inside faces that will mate with
the center cabinet, I decided not to add the X detail just for simplicity. Next up is the center
cabinet with the divider to make the hidden back compartment. I made a back support frame to mount
the TV lift cabinet mechanism. I decided to secure the back support to the cabinet sides with pocket
hole screws. Pocket holes were drilled along each side of the back support. Center cabinet assembly
starts with gluing the divider panel onto a side panel. Then add the bottom piece and make sure the
I secured the back support with pocket hole screws. Now to glue the cabinet guts to the
face frame and use all available clamps on deck to hold the cabinet tight.
The barn doors are simply face frames with slats glued to the back and X details added in the
center. I varied from this plan a little bit. I was afraid that with the cheap barn door hardware
that I bought that one and a half inch thick doors would be too thick for the hardware. I decided to
make quarter inch thick slats and inset them from the back of the barn door frame. I glued up the
barn door frames just like the face frames. I added the chamfer to my slats and set the router depth
to the slat thickness. Then I routed a one inch or so slot around the back side of the frames.
I measured the depth for the X detail pieces, then cut the X details just like I did on the
side panels. Now that the doors are hung, this was a bit of an overkill. One and a quarter inch
thick doors would have been perfect for the barn door hardware I bought. So maybe use three quarter
inch thick frame pieces and glue half inch slats to the back. I sanded all the cabinet pieces smooth,
then used briar smoke to stain everything. With the briar smoke style of stain, I apply it to
the cabinet and let it fully dry. Then I use fine sandpaper to lightly sand the stained surface.
Then I remove all the dust and apply two or three coats of satin polyurethane, making sure to lightly
sand in between each coat. The cabinet tops can be attached with top brackets, Z clips, or pocket
holes. I used the pocket hole jig to add pocket holes to the back side of the face frames. On the
underside of the edge of the top pieces, I added a small chamfered trim piece to make the tops look
thicker. I attached the tops with pocket hole screws. Now it's time for the moment of truth,
adding the TV lift cabinet mechanism. Installing the TV lift cabinet mechanism was really pretty
easy and straightforward. The TV lift cabinet mechanism is installed in the center of the back
support about an eighth of an inch from the top. I use the provided hardware to secure it to the
back support frame. Now extend the TV lift and attach the TV mount bracket. For the lid, I debated
between euro hinges and a piano hinge. Ultimately, I decided to go with the euro hinges so I could
place the cabinet tight against the back wall and the lid wouldn't need three quarters of an inch
clearance for the hinge to open. Plus, I'm really familiar with euro hinges and I like their
adjustability. These euro hinges are full overlay frameless hinges. To mount the TV, adjust the TV
mount bracket height for your TV, then secure the TV to the bracket with included hardware.
Since my console table is on carpet, I decided to secure the cabinets together with screws.
Pilot holes that are the same size as the lag screw shank are needed to install the barn door
hardware bar. I temporarily installed the bar and marked the locations of all the lag screws,
then drilled all the pilot holes and attached the bar with the included spacers.
Then I attached the roller hardware onto the barn doors. I'm thrilled at how this console
table turned out. I love all the slats and the X detail and the barn door hardware rolls really
nice and I love the hidden TV. I think it is so fun. One nice thing about this console table is
that this wall is visible from my entry and my family room and so it was kind of ugly having
a side view of a TV mounted to the wall and this console table is so much cuter. It's really nice
to be able to have some knickknack showing and then open up the doors for hidden storage and
then of course the TV lift is amazing. It's really cool. You can find the free plans for
this sliding barn door console with the hidden TV lift on my website hertoolbelt.com and I
hope you will subscribe and give me a huge thumbs up. Thanks for watching!