Reclaiming Attic Storage Space Over Thick Insulation!

How Do You Do It?
70 followers
34 Video ViewsยทOct 30, 2022
In this video, I'm going to reclaim my attic storage space,
and we're going to do it right now.
Look at all this stuff. So much stuff.
So step one would be get rid of some stuff,
but I'm going to skip right to step two and that is create more attic storage.
So here's what you see when you come up into my attic.
If you look to the right,
you have all that storage and then you have all this.
That's kind of open, but I could store stuff,
but I'm going to be doing some remodeling down here. Super secret.
Don't say anything about it. And then over here,
you have what used to be a nice storage area used to be all
nice and wide open.
And then I had to go and remodel my living room and dining room.
And when I remodeled the living room and dining room, I put this beam in,
which you can see, and to bring it up to code,
I added all this insulation.
And the problem with that is the ceiling joists
are underneath about six, seven inches of insulation right here.
So typically like these boards,
you would put them right on top here and you'd have a nice storage
area. But in order to do that,
I'm going to have to do a little more than just add plywood.
So there's a couple of ways I could do this.
I could just add whatever height this is
and put a board,
probably a two by six on top of here going the whole length of this
joist and continue that all the way down.
I'll take this out.
But what I'm going to do is I'm basically going to build like
mini walls out of two by threes.
So I'll build a wall here.
I'll use the beam as my first joist, if you will.
I'm going to have to build that up a little bit,
and then I'll build a wall here, wall here every 16 inches.
And then I can put my plywood on top of that.
And when I got this beam engineered,
I made sure to make it so that it could support
light storage, which is what this is going to be.
So every attic is different.
I know that mine is capable of supporting this weight and you're just going to
have to figure out if yours is before you do this point of
insulation,
or I should say the way it works is you don't want to squish it.
If you squish this in to whatever cavity you're using it for,
that kind of defeats the whole purpose of the insulation.
It's made to have air gaps. That's what helps it to insulate.
So I'm going to try not to crush that as much as possible and put the walls in
between them. So I'll have the same R value that I do right now.
So I have kind of a good idea of how I want to do this.
So I'm going to go get the materials and we'll go from there.
Well, that was expensive. 423.81.
The two by threes are $4.98 a piece and the
plywood's $27.45.
And I got OSB 7 16ths, the cheapest plywood they had.
This is January of 2022. Happy new year.
Hopefully this doesn't go on much longer. I hope the price has come down,
but it is what it is.
I don't see many other options in order to do this job.
I saw these like legs that you could like attach to your
ceiling joists. They sit on top, but then you still have to buy the plywood.
And those alone were like 300 bucks.
And I don't even know I'd probably need two or three of them to cover this whole
thing. So I think this is the cheapest solution.
I really want this attic storage space back. So we're doing it.
I have a scrap two by three
and that will give me enough where I'm not crushing that insulation down.
Five and a half inches. A two by six would have been perfect,
but I didn't want to put them on top of here all the way across eight feet
because I would have had to pre-drill halfway through the thing and then
drill into this.
I think building miniature walls is going to be easier and more
stable. This is going to be my first joist.
The platform's going to start right here.
So I'm going to cut my first wall at 37 inches.
I cut two of these at 37 inches.
And the reason I did two by three instead of two by four
is just to save money. In case you're wondering.
So there's my top and bottom plate for my mini wall.
And I'm going to measure 16 inches,
16 inches. Mark them. This,
cut my studs. So to cut my studs,
I need the total height of this wall to be five and a half inches.
So this is my top and bottom plate.
That's three inches because they're an inch and a half a piece.
So five and a half inches here, minus three inches,
one, two, three, two and a half inches.
That's what I'm going to cut all my studs at. Just to make life easier.
I made a mark on my chop saw. You can also use a stop block.
Something that I just realized is this is a two and a half inch block.
These are two and a half inches. Exactly. So what I'm thinking of doing
is just making these solid and make it like a mini I-beam almost.
My two by three on top there. I still need to screw it down.
Piece right here, right in the middle of that beam. Cool.
So then when I put my insulation down, just like that,
plywood will go right over that. Cool. I can attach it.
Two and a half inch construction screws. So measuring for this next one,
I want it half on that joist down there.
So I'm going to make it 94 and a half and I can adjust it here.
I don't mind if it's hanging over or half on that way down here as long as it's
half on down there. So I'm going to cut one, two,
three, four, five of these for now and bring them up.
And for the interest of saving on material,
I'm going to try and build these with the two and a half inch studs or blocks
and hopefully I don't split them. We'll see how it goes.
Put a half on the ceiling joist right here.
Try to make the insulation nice.
Crush it down without crushing it down too much.
Now here's a closer look at what I'm doing.
I'm putting the screws like this down into the joists,
about every other one.
And what's going to hold this together really is when I put the plywood on top
and screw it, it's not going to go anywhere.
There'll be no lateral movement. So I'm just going to continue this way.
I'm not going all the way to the end, but I'm doing one, two,
three more on that side. Okay.
That's as far as I'm going to go right there.
Let's get a piece of plywood on here.
I want to make this a little easier to walk around up here.
So here's the thing about the plywood.
There is no way a four by eight sheet is going to fit up this small ladder.
And in fact, even a half sheet, a four by four will not fit.
So I'm going to rip these the long way and bring them up in two foot by eight
foot sections or whatever my cut has to be.
This is going to take a while with two foot sheets like this,
but that's all I can do.
And I'm just going to use inch and a quarter drywall screws because they're
cheap and I have them. They will be just fine.
I changed my mind already. I'm going to do a full eight footer here,
and it's going to extend to about here, about another foot off of that.
I'm not going to put another mini wall underneath it.
It's just such a small space that you're not going to be able to walk there to
fall through the ceiling. Um, you know,
hopefully you don't roll over that way.
And unless you're stacking up gold bullion over there, which I have none of,
we're not going to have any issues. It's just going to overhang.
I think it'll just look a little cleaner. So I'll put full eight footers that way.
I'll use this for a cut.
So I'm going to take this out and bring up an eight footer.
There we go. Looking great.
So we've already added 48 square feet of extra storage space.
And it's really not that bad. You're going to have to duck your head,
but it's fine.
And what I'm going to do is continue this way.
I'm going to do all of this with the same straight seam like
this. If this was structural or a finished floor or something,
I would be staggering the seams here. Um,
and I kind of wish I was staggering the seams. That's just me,
but it's going to be easier to run these out,
plywood this whole thing,
and then work my way from there and come back this way because there's
a spot over here that I don't want to cover because I have to do some work
there. Keep on trucking. Okay.
It's the next day and I got myself a nice bright light so we can actually see
what's going on. Should have done that to start. This is way better.
So my next steps are, I'm going to fill in that piece on the beam.
I'll just measure and cut a two by three,
attach that and take a look at this. Almost made it.
I only have eight foot stock, so I'm not going to run out and get 10 footers,
but what I'm going to end up doing is just making an eight foot mini wall
like I've been doing here.
And then I'll add a two by three block to each end,
kind of like that. And that'll make up the difference.
So I'm going to do one, two, three, four,
five of them at eight feet plus those blocks and cut my piece here.
Got my first split. That's what happens when you use pieces of small,
especially when there's a big knot like that.
So keep that in mind. Well, this is looking awesome.
That right there is 128 square feet of storage that I have reclaimed so far.
Awesome.
Remember the only reason that I am cutting these sheets is to be able to get them
up here.
So what I'm doing is I'm ripping them in half and then I'm butting them
together. See if you can see the cut.
If you put them together the same way, it'll be nice and tight.
You can't even really tell that they're a cut piece. Just a little tip for you.
So time to do the same thing on this side. Nice.
I decided to use that cut piece over here.
All set. I stopped right here.
I left these long for the future. If I want to add more,
I have some wiring and stuff to take care of under there.
That's why I didn't want to cover it. And again, like I say,
in most of my videos, there are a bunch of different ways to do this.
It depends on your situation, what your attic is like,
if it is able to have storage above it.
I could have used two by sixes and gone all the way across,
but then I would have had to do them every 12 inches because if I did them 24
inches with seven sixteenths plywood, they would bow too much.
But then I'd have to step up to three quarters if I wanted to do 24 inches on
center. And if I did 12 inches on center, it would have been more money.
So there's all kinds of things that you can take into account and just do it in
a way that makes the most sense for you.
This made the most sense for me and I am thrilled.
This is kind of a special video for me because this video is the first one to
since I hit the milestone of 300,000 subscribers.
So that is insane.
I can't even like put into words how I feel about it.
I never would have thought I would have been here when I started this channel.
So just thank you a million times. Thank you.
I didn't want to make a dedicated video about it.
I wanted to make a video that you're used to seeing and the reason that you
subscribed.
So just wanted to bring it up and tell you how much I appreciate it.
And if you're not subscribed,
this is the first video you're finding of mine. Consider subscribing.
I make all kinds of home repair videos, time lapses,
and I don't plan on stopping anytime soon. In fact,
I just got a whole bunch of new video and audio equipment to take the production
value up a little bit, see how it goes.
So I'm looking forward to the future and I hope you are too.
If you want to see more videos like this,
you can click here-ish and here-ish and check those videos out.
And as always, thanks for watching.
I really appreciate it.
