Part 6 - Drywalling for Beginners - Building a Tiny Office

Workshop Edits
134 followers
94 Video Views·Jul 31, 2024
what's up guys I'm Zach and welcome back
to Workshop edits and welcome to episode
six of my tiny office build Series in my
backyard in today's episode we are going
to be tackling drywalling now I am a
total Noob at this so hopefully the
research that I did and the tips and
tricks that I give along the way as well
as just the detailing of how I tackled
my particular build is super insightful
for you guys because I learned a ton
along the way why are you riding
let's go ahead and get started got the
entire exterior of the build all
finished up and I also installed a
couple of these modern looking Farmhouse
scones that are Dusk to Dawn so they
turn on and they have like Edison low
temperature light bulbs and it looks
really good I it's really exciting just
to have the entire exterior done so we
can move on to finishing the inside so
we're going to start with drywall so
I've never done drywall before so this
video will definitely not be like a
comprehensive how to do it I've done a
huge amount of research and I'll
actually link probably what I found to
be the most helpful videos that are just
like very good step by steps if you are
a total Noob like me to doing drywall
but I can at least walk you through a
couple of tips that I learned and the
process that I'm going to go through to
wall this off because it's only one room
it's Square I don't have to do the roof
I think it's going to be relatively
straightforward but I'm sure I'm going
to run into some pain points along the
way so the most complicated part I think
of this is going to be doing the drywall
that goes up in between the these joist
up top so what I plan to do at least for
this back wall is to do drywall
vertically so instead of doing
horizontal sheets which would lead to
more butt joints I'm going to do
vertical pieces which will allow me to
have no butt joints on this back wall
the way that drywall works is you have a
butt joint cut end and then you have the
soft rounded over like Smooth edges and
if you look very closely at those
rounded edges you'll notice that while
the overall sheet is a half inch thick
on the very edge it dips in just a
little bit and the reason for that dip
is so that when you put those two joints
together it allows space for you to
actually put tape and mud in between and
you have to do it's it's a lot easier to
do the overall application of taping off
those joints and smoothing those edges
when you are doing butt joints which are
either just the short ends of the
material or any cut edges it's a much
more involved task of putting that tape
and sort of finding a very long drawn
out way to smooth those two pieces
together because you essentially have
the taped mudded joint sticking out a
little bit further than the material so
my overall process for pretty much
everything in here but at least this
back wall both side walls honestly all
the walls is to avoid doing any butt
joints if possible because it's a noob I
just know it's going to be a lot
trickier than a process that I'm already
unfamiliar with one thing that I really
wish I had thought through but I'm not
really sure how I would have avoided is
being able able to get a 10ft sheet in
this room because it would make all of
the horizontal joints like way easier
but there's no way for me to actually
maneuver a piece that's bigger than 4x8
into here just because of like where the
window is where the door is like there's
just literally not enough distance so
that's why I'm going with the vertical
joints for anybody who's like in the
comments watching this I have read that
like over really big spans doing
vertical drywall is not like the best
idea because it can kind of like by
having it horizontal it gives you more
studs to attach to so it's just going to
be flatter I don't really see how that's
going to be a problem here so I'm just
going to go for it so I have/ in 4x8
sheets of drywall I have my big drywall
Square I've never cut drywall before but
everything I read says have just a
scoring blade and then you can break
those pieces apart so what I'm going to
start by doing is this back wall I'm
going to butt a piece that is cut to the
proper width to line up with my studs up
against the roof so that then I can Mark
out where I need to cut out the notches
for the joist which are up here and then
I'm going to repeat that pattern across
I'm going to have to do it again for the
joists that are up here as well and then
the side wall should be hopefully really
straightforward I just have to get that
angle right there correct but
trigonometry baby one other thing that
you have to do when doing drywall is
make sure that you are taking accurate
measurements of where all of your
outlets need to be cut out or electrical
panels or light switches here that's
just something that's like definitely
measure it twice before cutting I have
done that a couple of times like in my
shop and I consistently got it wrong and
I've tried to learn from like what my
mistakes are with that so we'll see
because drywall can absorb moisture it's
best to place drywall half an inch or
more off of your subfloor so I'm just
going to use a half inch spacer and take
that into account for all of my
measurements once you put in flooring
and trim or baseboards at the bottom
like all that gets covered up anyway so
it's definitely something you should do
one other thing that I didn't take into
account and I researched it when you are
doing
framing with the intention of doing
drywalling there is a specific type of
corner joint that is called a California
joint or a California corner and
essentially here I'm going spin you
around essentially what it does is back
in a corner like this the framing for
this wall right here is all the way back
here so there's nothing on this side to
to actually attach the drywall too so a
California corner is essentially what I
went back and added which is just some
blocking for that drywall to rest up
against so it's going to rest up against
the floor here I have blocking there
blocking there and then obviously it's
going to rest up against here if you do
a true
California joist Corner whatever it's
called you'll have a beam that runs all
the way here and I'll put a visual of it
but I ended up doing that over here
because I didn't have it and I did some
big bigger ones in this corner and in
this corner so just like one more thing
to take into account so with all those
like little tips in mind new process for
me I will bring you along for the
journey and show you show me installing
it and I'll call out like any other of
the pain points that I seem to run into
I'm really hoping this process goes
smoothly because I oddly think it's
going to be enjoyable and I'm really
excited to enclose everything in now
that I've gone back and like double and
triple checked all of every single like
electrical thing and everything is like
ready to go for this so it's a super
exciting thing last thing that I'll call
out is in a previous video when I was
installing the receptacles that would
eventually house the sconces that are
outside I was using wallmounted plastic
ones which I truly don't know if those
are rated for outd doors but I did go
back and I'll show you I swapped them to
these metal junction boxes which seem to
just be the overall like go-to of what I
should be using so I swapped those also
so nobody yell at me uh for using the
wrong thing in a previous video cuz I
fixed it and they work great time to get
started so I've decided I'm going to
start in this back corner and the reason
for that is from this corner to here to
on Center is 44 in it would be 48 in but
that's from if I was measuring from this
outside stud that's kind of where the
California Corner comes into effect but
that allow me to use the most of one
piece of sheet here versus starting on
that side and then having to work my
like I'm going to end up with the least
amount of waste so what I need to do is
measure half inch off the ground to have
allow for the spacing to be off the
subfloor up to this height right here
then the extra height here and Mark out
where I'm going
to notch out all those so I can raise
the piece up one thing that I didn't
think through and I don't really know
how I would have gotten around this at
all unless I literally didn't follow
code is these hurricane ties are going
to be covered on this side but you are
going to see them on the beams up here
I've sort of just embraced that this is
a mistake or like a visual thing I'm
going to have to live with the only way
I could see doing this is like literally
removing them which I don't want to do
because that's not how you build things
or I could potentially cover these beams
with like faux
beams down the road if they're really
bothering
me but I'm not going to do that right
now
[Music]
can I come in your off
mhm D's getting ready to hang up some
stuff in the
office how was dance good
yeah why are you
riding drawing out a big straight line
why cuz I'm measuring so I can put this
in there no yeah
it's close need to cut a little bit of
relief
totally wrong don't know how I did that
got to fix
[Music]
okay number two lot smoother process I
learned so much I'm going to have to
hide a lot of mistakes on that first
piece piece number
one piece number two lot
cleaner and look I got the outlet
[Music]
right I got one whole side done those
were a little trickier than anticipated
but zero butt joints so feeling really
good about it just going to be rinse and
repeat I'm going to do the opposite wall
that has the sliding door on it next and
then finish off with the window and this
wall right
[Music]
here a full inch off
I've got this board secured in place in
all of the like critical points I'm
going to take I don't have like one of
those drywall trimmers but I have a
router with a flush trim bit so I'm just
going to Route out that piece here it's
probably going to be super messy but I
think it's the cleanest way to do it
overall
[Music]
[Applause]
[Music]
one thing I didn't anticipate is working
with full sheets of
drywall in a very tight space
I had to cut to width first so that I
could then take the measurement well I
had to cut to width first before I could
take the measurement of the angle up
here and translate to the board just so
I could have the butt joint in the
corner here and have the nice tapered
edge here to make my mudding
easier I'm pretty bad at somehow
measuring in these boxes so I'm just
marking here and here and I'm just going
to put this piece in place and then cut
around it with the power off also marked
right here and then on the upper side of
the window cuz once I get this enclosed
I'll know where I can start my
router and Route out the window
[Music]
perfectly he if it
got my last piece placed here and I
marked out exactly where my electrical
box is so I'm going to pull it back off
use the jigsaw just to make it like
super easy to cut that'll be the last
piece I have to hang from the looks of
it I think I marked it out
properly that's not right finished all
of the main parts and I have a couple of
mess ups I have no idea why I have so
much trouble measuring out these gaps
but I've got one here to fix and one
here to
fix maybe one more in that corner um
what I'm going to do is just use thin
strip to go behind in these areas where
I can and then I
can you know screw those in from behind
and then attach drywall on top top of it
and then we'll end up mudding over the
seam so I've never done this before but
I think it's pretty
straightforward it'll work
all right so that is going to wrap it up
for this episode hopefully that was
entertaining insightful and you learned
something along the way now if you are
watching these in real time make sure
that you are subscribed to the channel
so that you can be around and be
notified when the next video in this
series comes out if you are watching
these later on I will have a playlist
linked to every video that is launched
right here as well as the next episode
in the series right here if you have any
questions about this project materials
process some stumblings that I went
through or you just want to generally
understand where I got some of my
information from so that you can combine
it with this video and do your own
research please feel free to leave a
comment and like always I would be more
than happy to respond and give you as
much information as I can I'll see you
guys next time on whatever it is that
I'm building bye
