00:00 Why scarf joints matter in boatbuilding 00:08 Project intro – Poulsbo Boat build 00:33 Milling stock for long laminations 01:23 Surface prep and epoxy bonding basics 02:15 Hook scarf vs flat scarf explained 02:47 Scarf jig setup on the table saw 03:38 Glue-up setup on the bench 05:30 Preventing movement during glue-up 06:28 Using wax paper and clamping strategy 07:05 Why epoxy is ideal for scarf joints 08:11 Two-part bonding process explained 10:24 Thickening epoxy with colloidal silica 11:36 Aligning and fastening scarf joints 14:08 Clamping strategy and pressure tips 15:05 Using a strongback as a glue-up bench 16:25 Mixing fresh epoxy and timing 17:56 Clamping pads and shop-made solutions 18:48 Alternative alignment methods 19:05 Why epoxy allows shorter scarf joints 19:44 Final thoughts and wrap-up
poulsbo boat, scarf joint woodworking, scarf joint boat building, epoxy woodworking, west system epoxy, wooden boat building, boat building techniques, scarf joint jig, woodworking tips, laminating wood, strip built boat, nomad boat building
AI Generated·May contain errors
Now I think the most frequently used technique in wooden boat building is making short stuff
longer using scarf joints. Welcome to Nomad Boatbuilding, I'm Mark Rutin and today we're
going to scarf up a bunch of long skinny things using products from our sponsor West System Epoxy.
Now I'm working on a bunch of parts for my current project, this 15 foot poles bow boat.
I'm going to be laminating them in place out of thinner stock because this boat's got a lot of
shape to it and a lot of twist. But I want to scarf those parts to full length first before
I try and bend them in place. Now because I've got to scarf up a whole bunch of different parts
all at once, I want to try and glue them all up at once or at least glue them up in batches that are
manageable but also efficient. And so today I want to show you the techniques that I most often use
when I need to glue up a whole bunch of like-sized and shaped parts.
The first thing I need to do is to get a bunch of materials milled up in order to make my long
skinny things. Usually I'll start at the thickness planer, take my rough sawn stock and I will
thickness it down to what will be my finished widths. And then over to the table saw to rip out
all my individual pieces. Now usually I'll try and make sure there's a clean dressed face on the
inside of my lamination, that is the side that will be exposed later on. And all these other
surfaces can have a sawn face because I'm going to be laminating with epoxy and epoxy loves a nice
toothy surface. Now we won't be doing any laminating of these parts in this particular video
but on that subject, had I run all these through the thickness planer and had smooth faces on all
the surfaces, I would probably want to give them a quick scrub down with some 80 grit sandpaper
before laminating because as I say epoxy does like a good toothy surface. The harder the species
you're working with is, the more important it is to do this. I'm working with Douglas Fir and
Alaskan Yellow Cedar. Both of those love epoxy and I could easily just use the planed surface
and get a really good bond with those. But if I were using something else, we'll say like maple or
ash or oak, any species that presents a really glassy surface after you run it through your
thickness planer, it's really important to abrade those surfaces with a coarse sandpaper before
trying to bond them with epoxy. Now if you've been watching me for a while you know I really like
using hook scarves. So hook scarf is when you've got this sort of thick nib end on the scarf. It
can have it on one or both ends. Now the advantage of this is that you can put mechanical fastenings
through this thicker end and if it's going to be showing through varnish or something like that,
it gives you a really nice clean glue line and that looks great. However these take a lot more
time to cut. For parts that are going to be buried underneath paint for instance, the simple flat
scarf is far more practical. So that's what we're going to cut today. Now we're going to cut all
these flat scarves on my table saw. I'm going to be using this little simple scarfing jig.
I showed you how to make this jig in a previous video. I'm going to link to it up in the corner.
But in a nutshell, it's a simple sled that rides in the t-slot track of your table saw
and it's got a fence on it that is set at your scarf angle and you just clamp your material
to it and make sure you don't saw into the clamp that's holding it there. That's all there is to
it. Now I sometimes will stack multiple pieces of wood onto this jig to cut more than one scarf
at once but honestly it takes a bit more fussing than it's really worth it. It's easier to cut one
at a time and re-clamp the next piece. Of course that little scrap could cleave your head in two
so be real careful about removing it. Now that our scarves are cut we can start the glue up process.
I'm going to do it over my planking bench and you might notice that my bench top sits above the base
cabinets by about three inches. The bench top is a big torsion box and it's raised up above the base
cabinets so that I have space to put clamps if I want to do a clamping operation exactly
like this. I like to use this freezer paper to protect my workbench from gluing operations.
It's got kind of a poly coating on one side. I get it from a big box commercial restaurant supplier.
It's about 30 or 40 bucks a roll I think. All right so I'm going to glue up all these little
stringers here. So what I think I'm going to do is I'm going to use this piece of material to
align them all to so I can clamp to this and we'll clamp down on this. So I think I'm going to use
little bits of paper in between each one. Place down this on edge and to that end I'll put some
packing tape on here. Okay so I've got that taped up that'll go here. I'll just clamp that in place
these apart and I think what I'll do is use a polymer nailer to just tack these
in one spot just to keep them from sliding. Then I don't have to really worry about that
when I do my clamp up. I can just clamp down and call it good. I don't have to worry about
clamping up the stack beyond the gluing area. All right because I want to isolate these layers
regular wax paper is the best way to do that because it's nice and thin to wax both sides
as opposed to the butcher paper that I use elsewhere. I'll just cut it into some thinner
strips and I'll just slap one between each layer. Of course we need a block to go on top of that
so I'll find something. Here I've got a scrap of material that was from the in-wheels themselves
so that'll be a good backing block. I'll just throw some packing tape onto that. Now we can
glue up scarves with any kind of adhesive but I most often do it with epoxy. Now I most often
use epoxy for this because epoxy doesn't require a lot of clamping pressure in order to achieve
full strength so I can focus my efforts on just trying to get all the joints for these parts
aligned and then sort of like stabilized so they don't move during the curing process.
I know the epoxy is going to achieve full strength. Epoxy is also a gap filling glue
which means it works really well with joints that aren't necessarily perfect and it also glues
end grain really well and when you think about a scarf joint it's actually got a lot of end grain.
And we're going to be using the 105 resin and the 205 hardener for this. Just one shot
of each is plenty. All right let's go do our glue up. Okay we're going to do two-part bonding on
this. I'm going to use an acid brush. These are typically available from plumbing supplies
and they're notorious for losing hair so either take a pair of pliers and crunch down on the
ferrule a little bit. Another good trick is using some water-thin cyanoacrylate glue. You put a
little bit of it into the ferrule there. Give it a blast of accelerator to get it to kick off
Glue the fibers right into the ferrule which works really well.
What I didn't do on here was give myself a good line to follow for laying these out. Let me
quickly draw a pencil line on here see where the edge of the haunch is.
Hard to see. We want to know exactly where the scarf
finishes off so we can adjust our scarf placement properly.
Typically you want to hold back on the end of the scarf by just a little bit. That allows for glue
to exist in the joint and to keep the joint from sort of overshooting its termination.
Now two-part bonding means that we first wet out our surfaces with unthickened epoxy and then we
follow up with a coat of thickened epoxy. If you recall my statement that a scarf joint is really
quite a bit of end grain. That's made very apparent when you do your wet out. You'll
notice the epoxy really drawing into the pores of that scarf face. Now if you were to paint some of
that epoxy onto the unscarfed portion of your stock you'll notice a real difference in how
the epoxy absorbs into the two separate faces even though they're adjacent to each other.
The more porous the species of wood you choose is the more important it is to do that wet out
and give it time to absorb into the surface of those scarf joints before you add your thickened
Okay. Okay I'm going to be using a little bit of the 406 colloidal silica to thicken this up just
a hair. I don't want very much. Maybe a teaspoon into there perhaps. Try that out. The reason you use
thickeners is when you want a little more volume of epoxy. The number 406 colloidal silica is also
commonly referred to as anti-sag. Some refer to micro balloons but this is not micro balloons.
Micro balloons don't have the same structural integrity that colloidal silica does. Micro
balloons I believe are more like the 407 clearing compound. Anyhow we're just going to use a little
bit of this stuff. Not a heck of a lot. This is just going to show there's a little bit of volume
of epoxy in this joint although I really don't need it too much because this bird doesn't seem
to be gobbling up all the epoxy. Just a light coat. All right now we're going to stack these
together. I'm going to hold back my scarf line by just a strong 16th or something like that.
And I've got my polymer nailer. I'm just going to drop a couple nails in. One on top. One on top.
Now you absolutely do not need to use polymer nails for this. You could use staples. You could
not do to do it at all. If I were not to use the polymer nails the only thing I would do different
is I would stack all these up carefully and then I would clamp down on the ends of the stock or
like outside of the scarf area such that the whole stack can't slide anywhere. So that's the point of
the polymer nails is they're going to prevent sliding. Okay. Put a pad on there. Just a little
bit of light pressure on either side of the scarf so that each feather edge has got some pressure on
it. I'm not going to worry about the middle too much and I think I'll throw one more clamp
clamping it together right in the middle of the scarf. I just wanted to get this squeeze going
first. Now remember if you're doing glue ups in an area that's congested always make sure that the
tail ends of your clamps are going inboard onto a surface that you're not bumping into all the time.
That is a... I won't call it a mistake. It's common for people not to really think about that and you go
crashing into your clamps throughout the rest of the day and you might upset them. Okay there we go.
That's done. Okay having a big long planking bench like I have is admittedly a luxury and I obviously
I built that on purpose because I do this kind of thing all the time. But if you're a hobbyist and
you don't have a big long workbench and you still need to glue up long skinny things and try and
keep them aligned, orderly, whatever you want to call it, what do you do instead? So one of the
things I've started to do as a general practice is set up my strong back a little earlier in the
building process than I used to and so I will use that strong back to do my lofting. I'll use it to
elevate my lofting board up to a more comfortable working height about knee height but after I've
done my lofting and I put that away, now I have the strong back set up. Before I put molds on it,
I will use it as a work surface to glue up long skinny things and we're going to do that right now.
Now the only thing I need to do is add a little bit of a panel to one portion of the
strong back where I'm going to be doing the glue up so that it supports the scarfs that I got to
clamp. Now I was hoping to use the leftover epoxy from my last glue up for this one but in the time
it took me to sort of get things together, I can feel that it's getting hot and you can see it
slightly foaming a little bit so this is kicking off. I can't use this anymore or rather it'd be
stupid for me to try and use it so we're going to make up a fresh batch. This shop is so small
there's always a lot of front end stuff that I try and get done before I set a mold up
because as soon as the mold is set up, it becomes a lot more restricted. Melamine coated particle
board makes an excellent clamping pad material when you're working with epoxies. If you give
them a generous coat of furniture wax, your epoxy will usually pop right off of them.
So this glue up was a slightly different approach. Notice how I used a piece of blocking in the
center to align it all to instead of putting one on the outside edge so that's because
it's an easier way to keep the two halves from getting glued together obviously.
So that's a trick you can try. It's not not much of a trick but anyway so that works pretty good.
The really nice thing about using epoxy for scarfing is that you can use really short scarves
and still get a good strong joint because of epoxy's ability to hang on to end grain.
You can also glue up very roughly fitting joints and have them achieve full strength. So here's
something you can try. Hop on over to the bandsaw and take a piece of wood and cut any old sort of
crazy shape into it. Take that apart, slap on a pile of epoxy and glue it back together. It's
going to hold on to that just perfectly. You can actually create really interesting decorative
joints using thickened epoxy and scarfing techniques. Okay folks that's it for today.
I really want to thank you for watching. I also want to thank all my followers on Patreon for
helping to support this channel. If you'd like to join me on Patreon I'd really appreciate that.
You can find links in the corner or down in the description. And lastly I want to thank
West System Epoxies for sponsoring this video. Okay folks, catch you later.