KTM 125 EXC - How To - Gear Oil Change

MotoAdventuresYT
21 followers
12 Video Views·Dec 5, 2022
Thank You For Watching.
Its best to use the correct gear oil provided in the KTM handbook.
I hope this video helps you do your own gear oil change.
This is a video on how to do a gear oil change on a KTM 125 EXE.
So this is what you need.
A nice pair of gloves,
your gear oil,
a bucket,
a ratchet,
a 8mm deep socket,
and a 10mm deep socket.
As well as an extension bar,
a 19mm spanner,
some tissue,
and a copper washer box set
for the drain and level bolts.
So first things first when you get to the bike,
you want to chuck the bucket underneath the YISO.
After you put the bucket underneath the bike,
you want to take the oil filler plug off,
and your 19mm spanner,
and put that to the side.
So after you take off your filler cap,
you want to get your 10mm deep socket,
your extension,
and your ratchet.
And on these engines you have a drain plug for the gear oil
right underneath the brake lever,
and it is a 10mm socket.
So you just want to get your socket on there,
crack it off,
and take that out.
There we go.
As you can see, it's already draining
into the bucket.
If it helps, lean the bike over.
Now, while you leave your gear oil to drain,
you want to get your 8mm socket,
your extension bar,
and your ratchet,
and take out your filler bolt,
which is right above the brake lever.
It's the top 8mm bolt there.
Crack that off,
and take that out.
Now, while your gear oil is draining,
I do recommend you put a little bit of your new gear oil
in the engine now while it's draining,
just to flush the old gear oil out.
So these engines only take 750ml of gear oil.
Luckily I've got a litre here.
Chuck a bit more in there just to get it through.
There you go.
A bit more to put in there.
You've now got plenty left for the gear oil change.
In the meantime,
I'm going to clean up the level bolt,
the drain plug,
and your filler cap,
just so it's all ready to be put back into the bike.
Good, isn't it?
So when your bike is done draining gear oil,
you want to put the filler cap back in the bike,
with your new copper washer,
and just gently turn it.
You don't want to cross any other threads inside the motor.
There we go.
Now once you've got it finger tight,
you want to grab your ratchet,
and you don't want to do it too, too tight.
You just want to sort of give it
that little bit, and then
a little bit more.
That'll be it, that'll be perfect.
Once you've put the drain plug back in,
you want to fill your bike up with at least 750ml of gear oil in your engine.
Once you get about halfway through the bottle,
you want to turn the bike straight up,
so that you can see when the gear oil will come out the level bolt.
Once you've got the bike straight up,
you want to keep filling up the gearbox with your gear oil,
until you can see very clearly that the gear oil is coming out the level bolt.
Once you can see the gear oil is coming out the level bolt,
you want to stop filling up the engine with gear oil,
and put the bolt back in there.
You want to make sure all the threads are very clean and clear,
and then get your 8mm socket,
and very carefully, at the end,
get your brand new copper washer,
and all you want to do is just,
very carefully,
slowly twist it in.
Not too hard, you don't want to cross thread any of the bolts in the bike.
Once you have it finger tight,
to the point that you can't turn it anymore with your fingers,
get your ratchet,
and you don't want to do this too tight,
so you just do it a little bit,
and that's it.
After you put your drain plug back in the bike,
you want to put your filler cap back on the bike,
just do it by hand,
and use your 19mm socket,
just carefully, not too much,
and there we go, and that's it.
