The experienced diesel techs who see this video will know what this is, for those of you new to being a tech or the just curious we will cover what kind of gear this is, why it looks funky, what it is used for and what application this one came from.
Alright, so students often ask, 'what the hell is this thing?' Today, we're looking at a unique component in the world of **gears**: the scissor gear. This video explains **how it works**, diving into its peculiar construction and **mechanical design**, which is a fascinating aspect of **mechanical engineering**. Understanding different **types of gear** like this is crucial for anyone studying diesel or mechanical systems.
All right, so the topic of this video is
what the hell is this thing?
All right, so I get that a lot of times from students
is it's a weird looking gear.
It's kind of hard to figure out
what would you use something like that for?
Why does it have bolts and springs in it?
And just for you guys that are new to the channel,
just like the card says, welcome to Charlie's Garage.
So moving on.
This is called a scissor gear.
And what I'm missing in this scissor gear
is there would usually be a set of springs
in each one of these that help adjust it.
So what a scissor gear is,
is it's a product that allows you to install a gear set
with less backlash in it,
but still allow room for heat expansion.
So start off by saying that you need
a little bit of backlash, a little bit of lash in your gear
so that when the gears heat up and expand,
they don't break their teeth off, right?
But if you put too much lash into a gear set,
it's gonna make noises
and could potentially cause wear there as well.
So in order to prevent that and have less noise,
they came up with what's called a scissor gear.
So what's unique about the scissor gears,
if you look at it from this side, it just looks like a gear.
But if we turn it around this way and look at it,
we can see that it is actually two gears, right?
You have a smaller gear and a bigger gear right here.
And what that means is that I can put this gear on,
mesh it with another gear,
and I can set this to about maybe say 3,000s, 4,000s of lash
and maybe it needs 8,000s for heat expansion.
But what's gonna happen is that as it expands,
it's gonna compress against those springs
that I talked about that are missing on this one.
And eventually what's gonna happen
is the two are gonna rotate and line up
like they are right now.
Let me get this in focus, right?
So initially when it's cold,
there's gonna be a gap in those like this.
But then when it warms up, boom, right?
So now I don't have that clanking, that wear,
but I also have room for heat expansion
where I'm not gonna break teeth when these things heat up.
These are very cool creation.
I've been told that they were created by Toyota
for their gear trains back in like the 70s or something.
And then diesel manufacturers started using them
in engine gear sets, but I might be wrong about that.
It's just something I was told.
If you know the real story, let me know in the comments.
This specific one, this scissor gear is a cam gear
out of a Cummins ISX type engine.
And another thing that is unique about these gear sets
is that you look at most gears,
when you put them on a shaft,
there's a key way or something that lines it up
to where it only fits in one direction.
And then you time it that way.
But this gear set, if you look in here,
there is no spot for a key way.
It's just a perfectly round bore.
So when this fits over the end of the cam shaft,
it's actually interference fit.
You have to heat this up and get it to expand,
and then it'll fit over that cam.
And then once it cools down, it grips that cam
and holds it pretty tight.
And then you have the retaining bolt
and that's that you can put on it.
So this is one where you wouldn't wanna put
any kind of lubrication in here
because that would kind of delete the point
of having it grip it tight, right?
So you put it on dry, heat it up,
put it on, let it cool down.
So how do you time your cam shaft or your crank shaft
if you're just sliding a gear on loose like this?
Well, on the overhead cams that you do this on,
you usually have what's called a cam wedge,
and you put that wedge underneath a cam lobe
and then rotate the cam until that wedge stops it.
Then you put this gear on,
and then you take your crank gear down below this
and rotate it to a certain timing position
where night number one and six are at top dead center.
And then you put the idler gear in between those two gears
and now the crank is timed to the cam.
So I hope you learned something in this video
about scissor gears.
If you have any questions about them
or any questions about cam gear timing in these big engines,
just let me know in the comments
and maybe I'll make another video about it
or I'll just answer your question.
Again, thank you.
Please hit the like and subscribe button.
The videos are growing, the channel's growing,
and I appreciate all you guys that watch.
Have a good one.