How-To Replace Your Coil Springs

BleepinJeep
7 followers
6 Video Views·Oct 21, 2022
How-To Replace Your Coil Springs
Hey guys, this is Matt with BleepinJeep.com and today I'm going to show you how to change out a
pair of coil springs. But first, check out my website, BleepinJeep.com. It's got all the best
off-road videos on YouTube, none of the boring stuff. You can also find our t-shirts there and
check out our Facebook page. Alright, let's get started. Alright, so the first thing you want to
do is jack up the front of the Jeep pretty much as high as you can get it. Alright, now put some
jack stands under the frame and then drop it down. What you want is for your axle to be hanging
off the ground like so. Alright, so next remove your wheel of course and then we're just going
to move this shock to get it out of the way and when you remove the shock it'll also allow your
axle to droop because in most cases your shock is going to be your limiting factor on a stock setup.
Now we've got another limiting factor here which is the sway bar and we'll go ahead and remove that
next. If you find that there's too much tension on the sway bar or the shock to get it loose,
you might have to raise your axle back up. Probably be a better idea to take these off
while it was on the ground but... Alright, now I'll just bend this down if I can.
I'm just doing that to get access to this spring because we're going to have to put a compressor
on here to be able to drop it out. Alright, so the next thing you'll need is this spring compressor
and I got this at AutoZone. Basically you can rent these for free. You just buy them and then
you bring them back when you're done. The part number on this one is 227036 and you don't have
to get this exact one but this one's pretty nice. The way it works is you just put it on your spring
like this. You pull these clips back, put it on the spring, and then push the clip into place.
You want to get it out as far as you can here and then on the second one you want to try to have it
180 degrees opposite of the other one. Sometimes that's not possible and what you want to keep in
mind is you're going to need to get a socket or something on here so you want to make sure that
you can have access with your impact wrench. Otherwise it's going to be a long process of
turning a little wrench on there. So let me crank this one down a little bit.
Alright, that one's tight. Now this one's a little more difficult.
I think I can grab onto it right there. Just have to make sure that stays in place.
Alright, so now they're both on there. They're pretty tight. What you're going to do is just
work your way back and forth. Pull this spring down until you can get it free out of here.
Also, make sure your axle is down far enough
to get that thing out. You can take these springs out without one of these spring compressors
but it's a lot more involved and you pretty much have to take off your lower control arm and a
bunch of the steering components and stuff and drop your whole axle down. I think this will be
a little quicker and a lot easier. Alright, the spring's compressing pretty good but one thing
I forgot to mention is this little spring retainer on the back here. You're going to want to take that
off and all it does basically is just hold the spring in place whenever you're fully flexed to
it from popping out of there. Okay, I've got it compressed quite a ways. I couldn't really get
these where I wanted them 180 degrees apart because of the bracketry down here but I think
I might be able to pull it off. Make sure to wear your safety glasses as this thing is just a bomb
ready to go off. I'm going to take these off and there it is. Alright, so now we just need to get
our spring clamps back and to do that I'm just going to take this and loosen up one side and
then the other side. I can't quite get this on here so I might have to use a wrench. Okay, now
I need to compress the new spring that I'll be using and to do that I'm going to open up these
clamps as much as they'll go and put one on each side. Now I'm going to try to line this up to where
that these clamps will be in the right position when I put them back in the Jeep to be able to
loosen them up with the air tools. If not, I'll have to use the wrench again which is probably
going to be the case. Okay, now I'll just put one on each side and tighten this thing up. To make
things a little easier you can add some oil to the threads. Alright, hopefully I'll be able to
squeeze that in there. Let's take it over and find out. Alright, I'll just take that spring,
orient it back in the right direction, make sure that the top's on top and see if I can slide it
in there. Looks like I'm going to need just a little bit of a pry bar. There you go. Alright,
so I've got the spring back in there. The clips aren't where I need them to be so it's going to
be a little bit more difficult trying to get this in place. Also the bottom of the spring
isn't quite into place yet and I can't even pivot it over there because of these clips.
But hopefully I can use the impact wrench on this side and hopefully I can use the ratchet
wrench on this side over here to get that off and we'll see how it goes.
Well that worked out pretty good. Now what I'll do is I'll just take my pipe wrench,
put that on here and try to pivot the spring into place where it needs to go. Alright,
then the next thing to do is reattach this spring clip back here that holds the spring in place.
Then you'll want to put a jack under, jack up the axle a couple times, reattach your spring,
your shock absorber here and then reattach your sway bar over here.
Okay guys, thanks for watching. I hope you learned something new today.
Don't forget to subscribe below and check out my website bleepinjeep.com. It's got all the
best off-road videos on YouTube, none of the boring stuff. We've also got t-shirts there and
you can check out the Facebook page. I appreciate it. Please leave your comments below and we'll see
you next time.
