Replacing a Classic Car Distributor and Coil, and Protecting Plug Wires from Header Heat!

Charley’s Garage
78 followers
We replace the monstrosity of an HEI distributor with a model appropriate distributor and coil on a 1968 Mustang. Talk about timing as well.
#classic #classiccars #mustang #ignition
AI Generated·May contain errors
Video Summary
AI GeneratedThe video demonstrates how to replace a bulky HEI distributor with a smaller, Ford-specific electronic ignition distributor to create more room for a cold air intake and improve the engine's aesthetics. The process covers everything from determining the correct firing order and timing to the final installation and testing.
Welcome to Charlie's Garage. In this video we are going to be swapping out this HEI distributor
for a smaller one. So first off, why are we switching out the distributor? The first thing
is I got a cold air intake and it is much bigger than my original intake and this big honking
distributor is in the way. And the second thing is that I think it's big and ugly and it's not
really a Ford-specific part. So what we are going to do is replace it with a smaller Ford-specific
looking distributor. So we got our whole setup right here. We have the new distributor. It's
much smaller. It's already got an electronic ignition in it so I don't have any points or
anything like that I need to swap out. Comes with a cap. Nice cap, you know, the same color as the
almost so it's going to look pretty good in there. The cap cover. We got a new set of plugs
and we got a set of insulators that we put on the end because the headers will get really hot
and burn the wires without these. We have a new coil and we have our new separators right here
that are cast aluminum. So one of the first things we want to do before we pull the old distributor
out is that we want to find and put the distributor in the correct position which is going to be top
dead center number one. Now one of the things that everybody needs to know is that the camshaft
is what determines your firing order. If this was a stock 289 engine this is the setup I would have
and that right there 154.26.378 would be my firing order. But you'll notice that it says
except 351. When we rebuilt this engine we went with a roller cam upgrade and the camshaft that
we put in now changed my firing order to what a 351 has which is 13726548. The only thing this
book has wrong if you look it shows the arrow showing the direction of rotation on the distributor
is counterclockwise and it even says so right there. Right here the 351 also rotates counterclockwise
but for some reason down here it said something different so that's obviously wrong.
But ultimately what I need to do is put this where number one is in top dead center
and that is going to be fairly easy to do. What we are going to do is take the distributor cap
off but before we take it off I'm going to trace my number one spark plug wire right here
and we're going to trace it to where it mounts on the distributor. Then we're going to make
a mark on the distributor down here at the bottom so that way when we take the cap off
we can rotate the engine and put my timing marks down here at top dead center and if my
rotor lines up with the mark I made on the base I know that I'm at top dead center of the
compression stroke for cylinder number one. If I'm 180 degrees out I know that number one is
at top dead center but it's on the exhaust stroke not the compression stroke. So if you've done
a lot of these distributors on a lot of the same engine over and over and over again
this is a step that you probably will skip because you know from experience where that
rotor needs to point. So really what I'm doing is trying to demonstrate a way for people who are
new to this to keep everything straight and in line. So if I look down here at the bottom of my
distributor it's kind of hard to see but there's already a mark there from where I've done this
previously in the past. So all I got to do is freshen that mark up so it's a little bit easier
to see and I'm going to do this off camera. So I'll make the mark I'll take the distributor cap
off and then I will show you guys what the rotor looks like when it's pointed at the right position.
All right so it's kind of hard to see but check out my rotor position is right there above the
black mark I made at the distributor base. I got really lucky as soon as I put that timing mark
there at zero degrees at top dead center I was right on the money maybe give a couple of degrees
difference right there which is fine because that's some advance that you turned into it but
that's okay. So what this tells me now is that I need to put the new distributor in here in a
position where the rotor falls in at about that location. If I'm a couple of degrees off either
direction it'll be okay as long as I give myself enough room to be able to move the distributor
like this to get it into the timing that I want. So right now we're ready to pull this distributor out
and then we'll put the new one in. All right so we got our new distributor stabbed I did run into
a couple of problems I'm not going to have as much room for adjustment as I thought because
I hit this sending unit there for my aftermarket dash cooling temperature gauge.
But I do have enough room here to get a pretty wide range of adjustment probably more than enough
to get it firing correctly where I want it. A couple things to keep in mind is that the
distributor is driven via or drives a shaft that actually goes into the oil pump inside the engine
sometimes that shaft will come out with the distributor sometimes it will stay inside the
block. Mine stayed in the block I had to pull it out with a magnet. Be very careful doing that
because they can drop down and miss the hole and go into the oil pan. I already have one floating
around in the bottom of this oil pan so be very careful with that. Once you get it stabbed in
rotate it you want to make sure that the base down here comes in seats down that way you make
sure that your gears are making contact that your oil pump shaft is going to be down and make contact
with the bottom of the distributor and it allows the o-ring to seal right there. So I got this to
drop all the way down I put my block back on it but I didn't tighten it down all the way because
we're going to put the cap on and then we're going to need to adjust this and be able to rotate it
after I get everything hooked up to do the timing. So what I'm going to work on next is
I'm going to put the cap on I know that I am close to top dead center so what I'm going to do is
double check my vibration damper timing mark make sure that it is located at top dead center still
because I did have to wiggle it around to get the distributor to drop. Then I'm going to basically
start putting my new cables on by starting out with this one being number one and then going
in firing order sequence counterclockwise. So I'll get the cap on I'll get a couple wires started then
I'll give you guys an update. All right so the distributor cap is on now locked in place got
all my wires run to their correct spark plugs with the boots installed and now the next thing
to do is to find a place to hook up the coil. Now on a stock Mustang that has power steering or AC
or stuff like that you would have a bunch of stuff in the way right here but since I have these open
spaces right here I might be able to find a place to mount my coil there on the side of the cylinder
head and then be able to run my wires to that. But first I got to take the old wire connectors
which were this one and this other one over here they went to the old HEI distributor
so of course now I got to figure out which one has power with wire on which one that
is the for the tachometer and so forth. Then once I get it wired up I'll go over with you guys which
wires go where on the distributor and the coil. All right so we got it all wired up
test firing running sounds good got a little exhaust kick you can probably hear that I got to fix
put the timing line on it see down here really hard to see on camera but I got it set to about
nine to ten degrees and then what I want it to do is when I rev up to about three thousand I
want a max of around 32 or 34. You can do that with your timing light. All right so we have
successfully put in a new distributor hooked up the coil got it timed correctly started it up ran
it tested it everything worked good so then we went to go put the cold air intake on. Cold air
intake fits it kind of sits really close to those two plug wires but that's okay we can move those
out of the way uh but the hiccup now is going to be right here you see how close the uh the air
cleaner out inlet right here is to the uh export brace and I cannot get the uh hoses on there with
it that close can't bend it one way because if I bend it one way to put this hose on and then that
one will be too tight so I'm gonna have to brainstorm on this one may end up having to go to
a different style of carburetor cover for cold air intake but for right now we'll just leave it
like it is it can breathe really easy through those you got the filter in there so we're all good
I hope you enjoyed this video please like and subscribe
let me know in the comments if there's anything else you would like to see thanks a lot
