How To Remove a C-Clip Axle Shaft

BleepinJeep
7 followers
12 Video Views·Oct 21, 2022
How To Remove a C-Clip Axle Shaft
Hey guys, this is Matt with BleepinJeep.com and today I'm going to show you how to pull
a C-clip style axle shaft. But first, let me tell you a little about my website,
BleepinJeep.com. There we've got t-shirts, we've got hats, we've got lots of cool videos,
and we've got discount coupon codes for all the parts you could want. So check it out,
BleepinJeep.com. Also, do subscribe to the YouTube channel and check out the Facebook page as well.
Alright, so there are two different kinds of axle shafts. One is a C-clip, one is a non-C-clip.
You may be asking, well how do I tell which one I have? If you don't know, let me show you a
little secret. Alright, so this tip is just for rear axle shafts. Front ones are a little bit
different. Most front axle shafts are going to be a non-C-clip, but there are some that do have a
C-clip. But on this rear axle shaft, this is a Dana 35 axle shaft right here, and this is a Dana
44. Now you can see a difference, and that is this hole right here. Now that hole means that
this is a non-C-clip axle shaft. On this one, which is the C-clip, there is no hole because
you don't have to get in there to unbolt the axle shaft. The axle shaft is held in in the differential
by a C-clip. Now, so to check that, all you're going to do is take your tire off, take your wheel
off or whatever, and then pull your drum brake. See if you have a hole or if you don't have a hole.
Now like I said, this one is held in by a C-clip in the differential, and this one here, which is
the non-C-clip, is held in with a backing plate that's bolted on behind here. That's the reason
for the hole is so that you can turn the axle shaft and get a socket through there to unbolt
the bolts. Now the bad thing about a C-clip axle shaft, it's similar to this except right here
there's a little ring. You'll see that in a minute with a clip on it that holds it inside the
differential. But if that breaks, say the axle shaft breaks right here, there's nothing else
holding this in there besides that C-clip. So your entire wheel and tire and everything is just going
to come right out of the vehicle, and that's a bad thing. C-clips are not good for off-roading
purposes. But enough about that, let's get in there and take this thing out. The first thing
you'll want to do is take off your wheel and then your drum brake so that you can see this part,
and then we're going to move over here. Alright, so now we're in the differential. If you don't
know how to get this part, check out my other video on how to change your differential fluid.
Alright, so now we're in the differential. I'm going to put it in neutral and then we can
rotate everything around so that we can get a clear view of it. Now I don't know how you can
see that here, but this is the interior of the axle shaft coming through. So that axle shaft
comes all the way through and it stops right there, and this version is the C-clip. So right there
inside that spider gear is the C-clip. Now this is your ring and pinion gear, or this is your
ring gear. Your pinion gear is back here. This is the carrier housing, and these are your spider
gears, and then that's the pin right there. Now to get that C-clip out, we need to move the axle
shaft in. Well, we're working on this side, but you can see this side, so we need to move it in
anyway. And to do that, we have to get this pin out. So before we can get that out, we have to
rotate it up like this, and you can see that pin goes all the way through from top to bottom,
and it's going to be held in in some way or another. Usually that's going to be a drift pin
or something. In this case, it's a little screw, some kind of a set screw, and this looks like a 12
point that I'll need to find to be able to get that off. Now it looks like this is going to be
in the way right here, so I'm going to have to take that off, find something to pull that screw out.
Once we do that, the pin will drop down. We'll be able to push the axle shaft over and pull the
C-clip. It's kind of like one of those puzzles you used to get as a kid, and one of those little
wooden puzzles or metal puzzles. You got to figure out how all this goes together and goes apart.
All right, so if you have a drift pin, what you'll need to do is get a punch
and punch that drift pin out of there one way or the other. Now in my case, the only thing I can
find to fit that is this quarter inch 12 point socket, which fits on there perfectly, but
as you'll see, I can't get the socket onto there without removing this piece right here. Now this
holds the carrier in. It holds the race in, which holds the carrier in, so I need to take this off.
Now this is torqued to spec, so you need to make sure to put that back to torque spec when we get
to that point. Also, when you take this off, you want to keep it orientated in that position. Make
sure that you don't get that flipped upside down or something. So I'm going to take this off, and
then I'll be able to get this off, then I'll be able to get this out, and then I'll be able to
get the axle shaft pushed in, and then I'll be able to get the c-clip off,
and then we'll be able to move the axle shaft out. Sound good? All right, I'm just going to set that
aside, keeping it in the same orientation. I'll just set it right up there, and now
I should be able to get to this. Pull that little screw out. All right, there's that little screw
that held the pin in. Now I'm just going to rotate this down. See if I can drop that out. Yep.
Now I'm just going to rotate it down far enough to get that just like that. We don't need it to
come out any farther, and now everything's just kind of floating in there. I'll reach... let me
move the camera so you can see in there better. All right, it's hard to get the light and
everything in here at once, but I'm going to do my best here. I've got that pin sticking out like
I mentioned. Now all I have to do is reach over to the outside and push the axle shaft in. You can
see that right there. Now that red thing, that's the c-clip, and I'm just going to push on it with
my finger, and it drops out. That's the c-clip right there, and that holds the axle shaft on.
There it is again, and you can just rotate it freely and push it out.
Now if I reach out to the outside again, you can see I can pull that axle shaft
all the way out. All right, before I move back over there and show you that axle shaft come out,
I'm going to put this pin back in and just kind of see if I can get that set screw back in there.
I'm just going to shove it in there like that. The reason being is because once I pull
both the axle shafts, and if that pin is out, those spider gears will just fall right through,
and then you'll have a mess because there's shims on the back side of those, and they have to be
set up just right. So don't let those spider gears fall out on you. All right, now I can carefully
pull that axle shaft straight out. There it is. Now let me show you what I was talking about
right there. As you can see, that's the c-clip axle shaft right there. As I mentioned, that c-clip
holds the whole thing in. Here's the non-c-clip axle shaft, which is bolted in from the other
side. Now we'll come over here and slide the axle shaft back in. All right, now let's reinstall that
axle shaft. First, I'm going to take that screw out. There we go. Now I'm going to push that pin
down and let it slide out. Now I'm going to slide that axle shaft back in. I'll put the
c-clip on there. It just slides in place. Come on. There we go. Now I'll slide the axle shaft
back out to the edge. Put the pin back up through. Make sure that you get that hole
orientated in the right direction. All right, now for this little bolt, make sure you clean
it off real good and use Loctite. I'm not sure of the torque specs on this thing, but it's pretty
small. I'm just going to use the good and tight method. You don't want to tighten it too much,
or you're going to strip that thing off in there.
By the way, I looked up the name of that bolt. It's called a pinion shaft retaining bolt. Just
FYI. All right, now it's time to put the bearing caps back on or the bearing cap back on. I put
some Loctite on there as well. The torque spec for this is 80 foot pounds. Now, yours is going
to be different, so it's your job to look that information up. On the Dana 35 c-clip rear axle
for the XJ, it's 80 foot pounds. All right, guys, so that's how you remove and reinstall a c-clip
style axle shaft. I hope you enjoyed it. Don't forget to check out the website,
bleepingjeep.com. We have all kinds of Jeep apparel. What else do we have? We've got discount
codes and coupons for all your off-road related parts and all kinds of other stuff too, not just
off-road stuff. Don't forget to subscribe to the YouTube channel and check out the Facebook page.
We'll see you next time. Leave your comments below. Thanks for watching.
