Removing valves from a cylinder head and what to look for!

Charley’s Garage
78 followers
Nov 13, 2026
A walkthrough on how to remove valves from cylinder heads. What the components are called and what they do. Key things to look for and important measurements that need to be taken.
In today's video we are going to learn how
to remove the valves from a cylinder head and talk
a little bit about what are the important critical parts
that you want to pay attention to when you
have these valves removed and what to look for.
So first thing is this is a rusty old training
aid. It's been sitting in the back
of my truck getting rained on so I sprayed it down with some
lubricant and kind of letting it soak in for a minute
and then we're going to wipe it off.
Uh,
But the lubricant is there to kind of help
the keepers come off in case they're rusted on there,
which they might be sitting out in the rain and stuff like this has.
This hasn't seen oil in forever,
so who knows what kind of condition it's in.
So in order to pull a valve out of a cylinder head,
you have to take the spring right here.
So you got this spring.
You have to compress that spring till you can get to the keepers,
which are right inside here in the middle.
And the keepers, when the spring expands and pushes
this retainer plate up against those keepers,
those keepers are what keeps that spring from
popping off of that guy.
I have seen engines run from the simple fact of a little bitty keeper
Popping off and the valve dropping into the cylinder.
So these keepers are really critical components, believe it or not.
So what do you need in order to do this?
So one of the things I like to do is I like to mark
my valves with what they are when I'm taking them out.
I got a blue nib marker here, got a red nib marker here,
so if I had a complete cylinder head
instead of just this piece of one with these two valves,
I would mark them as intake one, exhaust
one, intake two, exhaust two, and so forth.
Or if I had a four valve per cylinder on some engines, I
might mark them a little bit differently,
but I want to try if I want to be putting these valves
I was back in the head.
of making sure i have them properly marked
and try to put them back in the
same place they came from all right so new markers the other tool
you're going to want is a screwdriver magnet anything that
can help you grab a hold of those keepers and
keep you from losing them as you're
compressing it right so you're going to
compress the spring use the magnet to gather up the keepers
so we need the magnet
And then you need a valve spring compressor, right?
This is a heavy-duty valve spring compressor,
pretty big guy, but it gets the job done.
And so I'm going to take a rag, clean this up,
and then I'm going to show you guys how
to use the valve spring compressor and how to remove the valve.
So to use the valve spring compressor,
what we're going to do is we're going to be putting this in
on the underside bottom of the head where the valve face is down here.
And then this side is
going to go right up here on the valve.
So what you do, you kind of spread it out like this and
then you set it on there. And with this type right here,
what you really want to do is you want to
get it spread out far enough where you can get that handle closed.
So we're going to back off
Off the backside a little bit.
until we can get that handle to close
because I want to do the compression not by trying to
squeeze the handle down but by turning the thing I'm turning right now.
So now I got the handle
locked in place or at least I did
and you want to try to keep it
as straight on the spring as
possible. All right once you have it on there nice
and tight then you can start tightening
this back piece to compress the spring.
All right so in the process of doing
this I've come off center of my valve
and I probably should have gone with this bigger end on here
but I didn't want to mess with it
and this is what happens when you take shortcuts so
now I'm going to try to re-center this guy
so that it doesn't fall off then re-tighten it
and it's really really critical to have it centered
so you're not pushing down on the keepers.
So I was right about this one being rusty making it
way harder than it normally is. I literally bent
my prong down here at the bottom of my tool trying
to get this to go down. When it finally did break
though you can see that I got one keeper out.
Now I'm trying to break loose the other keeper
but the other keeper is being a little bit stubborn.
It's rusted in there pretty good
so we'll see if I can get it out of there.
It's being a little bare though.
All right guys, so I know I told you you just need
the valve spring compressor and the magnet.
I had to pull the hammer out,
tap this guy a little bit to free the rust off of that keeper,
but now we have both keepers out.
So you can see the keeper right there. You can see it's got the
ridges inside of it that clamp to the valve stem,
how it's tapered so that when the retainer comes
up on it, it can't go all the way through it, but it can go on it.
And that's what holds that
That valve in there is just
this little guy right here, two of them, right?
So these two little keepers, these guys right here,
they are basically the only thing keeping
your very expensive engine from blowing up
by having a valve drop in the cylinder.
It's just these guys. So very important parts.
When you take them off, you don't want to lose
them, not unless you have another set of them laying around.
All right, once you get the
The that off then you can take this off is a lot easier than
compressing the spring you just go up here to the handle
pull up on it and once you pull up
on it you can take your valve spring compressor off.
Now when we look at this guy we can see that right here
this piece that just fell out in my hand is
called the retainer that's the part that hugs
those keepers sits right on top of this valve
You've got your valve spring, you've got your retainer.
And then you pull your valve spring off,
you got your valve spring itself,
and then you can just simply take your valve, push it in.
You look on the back side of the head,
you can see that we're pushing this valve out.
Just grab it, pull it out,
and now you've removed the valve from your cylinder head.
So like I said, this thing's been sitting out in the dirt
and the rain. Look at that rust on it.
Not something you'd want to see out of an engine
that was running. That would be a bad sign.
So I told you guys we would talk a little bit about
the important pieces when you take a
valve out of the head that you need to pay special attention to.
So this here at the top, this is called a valve seal.
And this valve seal right here
This is the piece that is going to, this valve seal is going
to keep oil from dripping down in there and keep you from burning oil.
So a lot of times when you have an older vehicle that's smoking
a little bit, this could be the culprit is the valve seal, right?
So the valve seal itself, you might as well replace these.
If you've torn a head down to this point, put some new ones on there.
The hole.
That we push this out of so when you put this valve in here
And you see how it's riding in the head like that.
That part that it rides through is called the valve guide.
And the valve guides in a lot of engines,
because of the concept known as rocker arm
for us.
Tends to wear the valve stem
which is the guy that rides inside the valve guide
and the valve guide itself they tend to wear unevenly
and so you should take you a small
transfer gauge, a ball gauge,
put it in there take you a few measurements looking for taper
looking for excessive wear and then take you a micrometer and measure
your valve stem in three places to see if it has excessive wear.
All right, so valve guide, valve seal, valve stem,
all stuff you should take a look at and measure.
What else should we take a look at and measure?
We got our valve seat, right,
so our valve seat is this part right here
that this part of the valve sits in.
And what we want to do is we want to make sure that valve seat is nice,
clean, doesn't have debris on it, dents, scratches.
You may want to do a valve leakage
test before you even take this apart.
Because what you can do now is you can take this and if you can
do it at home, if you have the tools, or take it to a machine shop.
And what they can do is they can take this valve guide
and they can clean it up and make it nice
and flat and clean again. Not flat, they're all angled.
And then you got the part of the valve
that mates with it. This part can also be machined nice
and smooth and then that way when the two go
back in there together and this valve closes
and it seats up against that it seals properly.
All right, so one of the other key important measurements
on a valve is called the margin.
So when you're looking at a valve,
and let's put the light up here so we can see it better.
When you're looking at a valve,
you have what's called the valve margin.
The valve margin is the part of the valve.
It's not this top face of the valve here,
and it's not the bottom of the valve.
It's this little guy right between the two.
The amount of margin that you have is going to determine
how much surface material you can take off
of this part to make it seat better.
So if you don't have enough margin,
you need to replace the valves because you're
not going to be able to machine them.
All right, so I hope this was a nice little
walkthrough of how to remove the valve,
what to look at when you get them off, things like that.
Uh, but a lot of times, a lot of builders,
when they do this stuff, they usually just
take these cylinder heads to a machine shop
and have the machine shop do all that stuff
for them.
But it is good to know exactly what it
is the machine shop is going to be doing, why
they're doing it, uh, all that stuff.
Because the more knowledgeable you are,
when you do deal with machine shops, the less likely
they are, and most of them won't,
but the less likely they are to take advantage of
So...
understanding if they tell you that they can't replace
or resurface your valves because you have
bad valve margins or they tell you
that if you have aluminum heads you might need new inserted
valve seats things like that the more you know about
these guys the better. So if you have any
questions about any of the stuff we covered in here
of how to take the valve out what to measure
what to look for let me know in the comments
and let me know what other types of videos like this
Like this, you might like to see in the future.
Sorry about the poor lighting.
I started this video when the sun was still out
and it started to get kind of dark on me.
I forget this time of year, it's getting darker earlier,
but I hope you guys were able to see what I was doing.
Might remake this video in the future in more daylight.
Let me know what you think.
Thanks, have a good one.
Hey, remember channel memberships.
The more channel memberships I have,
the more stuff I can afford to make videos of
with this stuff.
I had a really nice camshaft,
a really nice crankshaft that I made videos on, and I bought
that with money that I made off of memberships on this channel.
So if you guys can become members,
what that does is it helps provide me with funds where
maybe I could have bought a cheap cylinder head at an auction
or something that was in
better shape than this one
and made a better quality video with a better cylinder head.
So becoming a channel member helps me create content.
I'd appreciate it if you guys consider doing that.
Thank you. Have a good one. I forgot that I
also wanted to talk about the valve spring a little bit,
right? So the valve spring itself
is what determines the closing rate and the closing
force of the valve. Remember your camshaft
and your valve train is what pushes down and compresses
this spring and allows the valve to open.
It's when those components come off of this that the
The spring expands again and closes the valve.
So the spring is critically important to the closing rate of the valve,
how well the valve stays closed.
If the valve is weak, you're going to have potential for valve bounce
and float and all kinds of issues going on.
All
That's why I highly recommend anytime you build an engine
and you do cylinder heads,
Get a new set of springs don't you know there's
a way to test springs you can test their
right.
how much lean they got you can test their free height
their compressed tension their installed
tension there's all kinds of tests you can do to a spring
but I just recommend not even worrying
about any of that stuff just get a new set of springs
when you're doing a build. Thanks.
