How to Install A Door Knob on An Interior Pre-Hung Door

How Do You Do It?
70 followers
120 Video Views·Oct 30, 2022
Okay, in this video I'm going to show you how to install a doorknob on a pre-hung
masonite door. Pretty simple. We got a doorknob here, locking doorknob, the defiant,
and these are the things I'm going to use. A screw gun with a phillips, a drill with a pilot bit,
hammer, I might need a flathead, maybe not, and a knife because I'll show you a little trick.
to doing this. It is simple but there is a really easy thing that you can do to stop what I find
is an annoying feature of these pre-hung doors. So we got our doorknob, here's our mechanism,
closes the door, and then we got our screws, and we got our door latch strike plate.
This right here, I have honestly never used these because I find them to be more annoying than
anything else, so I am not going to install this. You really don't need it. So, um, don't worry
about it. Throw it away. First thing you do is the mechanism. You want this part that's sloped
to face the door trim, and this flat part to face which way the door is opening.
You install it backwards, it is not going to work. And you just stick that in there,
and this is already mortised out, so it fits right in there. Now you want to pre-drill these holes
because this will split. Line this up, just like that. Pre-drill just really small, this is
an eighth inch I believe, or actually this is smaller, this is probably three sixteenths.
Right in the center of these holes, just like that, right here. Okay,
and you can take your screws, put those in, try not to strip them.
Now the mechanism is all set. This should be set here to this depth bore.
If you actually drilled this, you are going to have to set it to wherever you drilled,
but this is the standard right here. So you take this piece and feed it in through here,
just like that. And then on the back side, you want to make sure that this piece stays right
where it was as you took this apart. So it was like this. So the best thing to do is be ready
to put this in, separate it, put this piece in, just like that, and hold this the same way,
so that this actually goes into the lock. Just wiggle it around, find where the lock is,
make sure the plastic pieces line up with the other piece. You can install these bolts.
This might take some work to line up. You're going to want to do these as far as you can by hand.
And then I would suggest to do this with just a Phillips screwdriver. I'm going to use a drill,
but the problem with this is you can't get straight on here and you could end up scratching
the door knob, but I am going to not do that. And those don't have to be super tight. You just
bring them down, just like that. So don't lock yourself out of the room before you shut the door.
Make sure it's unlocked. Pro tip. Now you just have to install the strike plate. And this is
the thing that annoys me about these doors, is this is mortised. So if you put your strike plate
in here just the way they have it, what ends up happening, for whatever reason,
the way they built these doors is when you shut the door you'll have this, it'll be loose.
So my personal preference is to have the doors tight. There's no, so there's no airflow
and you can't see daylight through them. I don't like this at all. And
I'm going to go ahead and put this in. And I already know that I need to put this latch plate
about right there because I have hung a lot of doors and they are all like this. It's June 2018,
maybe they will change this, but since about 2005 they've all been this way. So you put it here and
you go about another 3 16ths of an inch, I'd say. And that's just enough to make the door tight.
So I'm going to take my nice sharp pencil. I'm going to put this latch right where they tell
you to put it. And then I'm going to move it another 3 16ths or an 8th over. And then I'm
going to mark around there. Just like that. And if you don't want to do this, you can attach it
just like this. It just won't look as good because it'll be hanging over the wood like that. So now
I'm going to cut this little piece out. Take a sharp knife and just follow along that line
like that. Kind of hard to make the round cut if you just kind of stab it like that.
Okay and then you can use a chisel if you want to do this or I just like to cut it just like that.
Just be careful of your fingers. And there's your piece. Clean that up a little bit. We're good.
Now you can put your striker where it needs to be and pre-drill right in the center here.
Like that. Get your screws. Line this up. The striker is nice and flush. You can shut your door
and it's nice and tight. You don't have that play that you would have like
it would do something like that. And that just really annoys me. If you have a window open or
something, say this window was open and somebody comes in the front of the house, the door would
be doing this. You know it's just really annoying. But now it closes nice and tight
and that fixes your problem. All right. Hopefully this helped you out. Hopefully you're entertained.
Be sure to check out all my other videos. I'm going to be posting an entire series about
how I remodeled this master bedroom. Keep a lookout for it.
Make sure to subscribe and all that other good stuff. Thanks.
