The BEST Way to Create an Interior Doorway Opening on an Existing Wall

Welcome to the Woods (Melissa Woods)
160 followers
18 Video Views·Oct 28, 2024
I am creating a new entrance to a large, underutilized closet in my old home. To open up a doorway from our primary bedroom into the space, I cut through drywall on one side and plaster and lathe on the other! Learn the tools you need and tips to add an interior door successfully!
Shop for Wonderblades here with discount code WOODS10 for an extra 10% off single blade purchases:
https://wonderblade.com/
Follow me on Instagram: https://www.instagram.com/welcometothewoodsblog/
Tiktok: https://www.tiktok.com/@welcome2thewoods
This big dark closet off of the bedroom upstairs of my home
has a lot of space but it's super underutilized with its slanted ceilings
and it just collects clutter. I'm going to actually
change this layout having a wall built in the middle
so that a smaller closet with polo drawers is on one side
and the rest of the space is customized for my master
So in this video I'm going to show you how I opened up a doorway
in this wall between these two bedrooms to
provide access to this closet from my master.
I am Melissa Woods and I do all kinds of DIY home improvement. If this is your
first time on my channel be sure to hit subscribe to follow
along this massive closet renovation. On this side
of the wall in my bedroom the wall is actually
composed of drywall. So this is the side I'm going to cut into first just because
it's a little more straightforward than the back side which is still
plaster and lath from decades ago. I plan to place the
doorway to my new closet near the window so that natural light
gets into the space and it's symmetrical with the other
closet opening on the opposite wall. To cut the drywall
I'm wearing a respirator and hearing protection and I'm
using my oscillating multi-tool with a plunge cut blade to
cut into the drywall right along the stud.
To find the stud I use a powerful magnetic stud finder which looks for the
screws or nails that hold the drywall onto the wall
instead of just trying to sense the wood behind. It's
so accurate that I confidently cut through the drywall
right along the edge of the stud. As soon as I started I realized I was going to
kick up dust all over my bedroom furniture so
instead of covering each piece with plastic I used
pre-taped plastic and created a little like room
plasticking off an area around where I was going to work
to keep all of the dust out of the rest of my bedroom.
This worked amazingly well. I taped it to the ceiling
and then I rolled it down and I taped a second piece so that the plastic made it
all the way to the floor. Back inside my plasticked off area
I'm going to continue cutting. My plan is to
cut a doorway between two of the wall studs. I'll only be removing one of the
studs. Now I know that this wall is not
load-bearing because it does not have a wall directly
below it in our floor plan but I know that removing
just one stud will put less strain on the framing of the wall
than if I were to remove more and frame in what is a standard size
door opening like 32 inches. Instead I'm just doing whatever the
measurement between those two studs comes out to. I think it's like just shy
of 30 inches. Now I want to speak to the particular
blade I'm using on my oscillating multi-tool.
This tool is one of the best choices for a saw to cut through
drywall but the blade is so important because you can see here not only does
it go right through drywall easily, you can also
continue down to your wood trim and it slices right through my
wooden trim as well. This is because I'm using a high
strength carbide blade and the maker of these
blades is the sponsor of this video, Wonderblade. This company focuses on
creating blades that are durable, high strength,
they're going to get the job done and they're going to last you a long time.
Their fine tooth blade can saw through the materials I'm showing here but also
even metal like nails or small screws in the drywall
if needed. Now it has a universal fit so it very easily installs on my
oscillating multi-tool as you see here and it has that plunge depth so I
can cut through even a one and a half inch thick stud.
You can get into tight spaces, you can cut
at whatever angle, this kind of tool is indispensable. The carbide tipped blade
was strong enough to even slice through plaster that was on the
back side of this closet wall when I was trying to relocate this light
but I wouldn't recommend cutting this material with this particular blade.
Later on I will show you the diamond crusted angle grinder blade that cut
through the plaster like a hot knife in butter. So now that my doorway is cut out
on the drywall I'm going to use my magnetic stud finder again
to pull the screws off. I'm doing this so I can actually
reuse this piece of drywall. My magnetic stud finder is so accurate and I knew
the the screws were phillips head that this
was a huge success. When it came off the wall I was so happy.
I can reuse this drywall now with no issues and
I didn't have a big dusty mess or a bunch of garbage to throw in the dumpster.
Because I followed my magnetic stud finder I cut
the first time along that stud so flush. I was amazed, didn't really have to do any
touch up. But the other stud I didn't do as
accurately, it went a little quicker and so I just cut this off so that the
drywall is flush with the stud. Then I removed the
box for the outlet that was there. I'm going
to relocate this on the other side of the stud to the left. I don't really
need to give it a lot of trim space because the
trim work I'm planning for this doorway is so basic.
I'm not going to put like regular molding. So I'm just
marking that out and I also used my oscillating multi-tool to cut
this as well. Look at how easy and accurate that is.
Now to cut through the other side of the wall that is plaster and lath. This is
going to be a lot more tricky. My first thought was to use the blade
to just get through the wood lath and remove the wood part. But when I
did this it caused the plaster of course to just
start crumbling all over. So I decided I did have to go around the
other side and mark out the same opening and then use the other blade for plaster
to cut through and prevent any excess cracking or crumbling.
This is Wonder Blade's tough grit diamond crusted ankle grinder blade and
this thing is designed to cut through the toughest materials like porcelain,
brick, cement block, metal rebar, steel piping, and plaster. You can see how
quickly I was able to work. You can see sparks coming up when I
would hit one of the nails attaching the lath into the stud and
you can also see all of the dust I'm creating. So
it's important doing a plaster wall that you wear
respiratory protection. I also sealed off this room with
plastic so that none of this nasty dust and debris would get into
the rest of my home. I sealed off the ventilation
to the room as well so it wouldn't get sucked into our HVAC.
Ultimately this was the solution I used to get through the plaster and lath and
I couldn't have done it without that diamond
crusted blade. It was so easy to cut through this tough material and
I had like this big metal nail sticking out. I'll show you
here just how quickly it sheared it off. And I noticed with
this blade, the Wonder Blade brand has these
areas on it that clear the debris. I've used other diamond
crusted blades in the past that were not as efficient and the blade
heated up quicker because it did not have
those areas to clear debris as you're cutting.
So the Wonder Blade Tough Grit one was definitely superior.
Now that my wall material is removed on both sides of my new doorway,
I'm going to mark off a with a square like a straight line
to cut my framing. I'm just removing this
single stud and again I reached for the carbide
plunge blade on my oscillating multi-tool to make
quick work of this. I also used it on the tight area of my base plate to
cut it flush with the stud. If you make this cut super
carefully you can actually reuse this bottom plate
2x4 because it's cut to the perfect width you'll need
to add at the top of your doorway and create a pseudo header.
So once I got all of that pried apart, the demolition aspect of this project is
finally done and I can remove my plastic protection. All the dust had
settled at this point and I used a shop vac to clean all of
the debris up. I can't believe before there was a wall
here because now I created a doorway. So the 2x4
that's going to go in the top, I drilled pocket holes and I'm going to be
screwing some kreg screws in at an angle to connect this piece of
2x4 at the top of my doorway into the two
side studs. I measured to make sure that this was an even height on both sides
but the finesse leveling will happen later
when I add my pretty framing around the door. I also
popped a couple long screws straight up through the center
into the stud I removed that is going to
you know rest on the middle of this 2x4 that I'm adding.
Alright at this point if you made your doorway opening
big enough to accommodate a like pre-hung door
you could just install a pre-hung door but since mine is this custom size
I am going to nail in the thinnest paneling possible
that I custom cut to the width covering the edge of my drywall, the edge of my
plaster and lath, and the side studs of the opening. I'm
using short brad nails and this paneling is only an
eighth of an inch thick. I want to keep this doorway as wide as
possible so I pick paneling as thin as possible.
Once both side panels were installed I grabbed my laser
tape measure and got the exact measurement to cut
this piece for the top. This is one half inch thick
plywood and it's a thicker more substantial piece
because I want to get this perfectly level. I needed something thick enough
and sturdy enough I could shim it up. So here I'm leveling this piece both
directions and shooting longer brad nails so that it goes through
the half inch plywood through my shims and into the 2x4
framing. Now I'm not planning to have a door on
this closet at all that's why I'm framing it up this
way. I know a lot of closets have doors but
I just don't think they're necessary and the other closet
off of this bedroom does not have a door. I plan to finish this off with some trim.
The top is going to have this 1x4 that matches a lot of the other trim in
this room like around our our door to enter and then I'm going to
put this like corner trim it just makes a 90
degree angle and this is pretty inexpensive but I
don't have enough to completely finish this door for this video I have to pick
up some more at the store. This is how the edge is going to look to
cover the panel I added and to cover the cut drywall.
Be sure to shop for Wonder Blade's incredible products
in the link in my description and subscribe if you want to see how this
whole closet renovation turns out. Also I have no idea how I'm
going to patch the floor here so any suggestions are welcome in the
comments.
