Welcome to part 3 of the Gold Tooth Mine build! In this installment, I finish up the structure by building the roof, building a simple base from foamcore, painting the figures and details, and adding the final weathering. Plus, a few more tips and deviations from the instructions to help make the kit your own!
The first kit from Thunder Mesa Kits is now available and it's the Gold Tooth Mine in 1:48 scale! At the time of this recording, there are still a few kits available but these kits are only being produced for a limited time. https://www.thundermesakits.com/
Thanks for watching, Dave ____________
Become a Thunder Mesa Member on Patreon for early access, exclusive content, and members only parts and details from the builds! https://patreon.com/thundermesa/
All music courtesy YouTube Audio Library, Creative Commons License.
AI Generated·May contain errors
Video Summary
AI Generated
This video concludes the Gold Tooth Mine build by Thunder Mesa Kits, detailing the final assembly of the roof, cupola, and mine shaft. It emphasizes realism through custom roofing materials, 3D printed accessories, and weathering techniques to create an authentic, weathered mining structure.
Howdy folks, Dave here for Thunder Mesa Trains.
Welcome back to the studio where today we have the third and final part of the
Gold Tooth Mine Build. The Gold Tooth Mine,
that's the first kit from Thunder Mesa Kits.
And though we do expect them to sell out as of this recording,
there are still some available on the website.
That's at thundermesakits.com and yes,
I will put a link in the description down below.
Now the Gold Tooth is a modestly sized mine building,
which occupies a footprint of just about eight and a quarter by three and a half
inches. So it doesn't take up a lot of real estate on the old layout.
And in the first installment we built the head frame and in part two,
I did the walls and the board and batten siding, the doors and the windows,
and the color scheme. Today,
we're going to finish this up by doing the roof, the final weathering,
and all the final details,
including those great looking figures from Characters Count Miniatures.
So the first thing I need to do today is locate this bag inside the box,
which has all of the laser cut roof trusses inside.
These are cut from some one 16th of an inch thick MDF.
And as usual, we've got a lot of ground to cover.
So let's jump right into the build.
Now I've laid out all of the MDF pieces here so you can see them.
There are six roof trusses like this with the longer rafter sticking out
and those are going to go over the bump out section on the building.
And then we've got six of the shorter ones, which is the standard roof truss.
Got three of these three by six rafters.
And those are for the cupola when we're ready to put that on.
And then we've got these four pieces and
two of these are going to be used for the main roof beam,
the ridge pole that goes across the top here.
And then the two are extra just in case you lose or break one.
So we don't need that and we don't need that.
We need one of the long and one of the slightly shorter ones.
And that little slot is designed to lock these in the proper upright position.
Otherwise, they would rock back and forth and that fits down
into the slots
that are cut into the sidewalls like that.
So to lock those into position and all be properly fitted all in a row,
they should line up.
So what I like to do is just go around and dry fit all of these pieces first.
If you do need to make some adjustments, a flat Swiss file like this
is probably the best tool for the job.
You can also ease this notch a little bit.
If you need to by taking down that corner right there.
Now you can add some wood grain to these rafter tails
and then I'm staining all of mine with
this dark gray wood touch up marker.
Now that I have all of those roof trusses
properly fitted and stained, I can start gluing them in.
And the first one that goes in
is this one back here, it goes flush with the back wall.
And when it's properly seated, you'll know because it'll
almost kind of like clicks into place.
And for the rest of these, I put glue into the slots
and then just push them down into place.
One place in particular, you're probably going to need to file
a little bit of material away
is the tops of these door and window frames.
For the most part, the roof trusses are on scale two foot centers,
except for this gap right here.
And that's to accommodate the diagonals of the head frame
coming down through there.
And now it's time to add the main ridge beam here.
And the reason it's in two pieces
is to make it easier to install.
This was all one long piece.
It would be very, very difficult to line up all of these slots
and get that just so no matter how careful you are
in installing the roof trusses,
you're going to have to do probably a little filing,
a little fitting to get these in here straight.
And this is the roof truss where the two sections of
a ridge beam meet.
So I'm going to start right here and put about halfway through there.
And it should overhang
out the end of the building by about six scale inches or so.
Let's get it started at one end.
And you want to push it all the way down in there until it is
just below or flush with the tops of the roof trusses.
And same thing with the shorter one.
We want them to meet right there and there.
There we go. Just like that.
And we have all of the chipboard roof panels,
and those are lettered A through F, and they're in different pieces.
I'll show you this real quick
so that they can fit around the head frame here.
Notice that the roof panels are not only scribed,
but they're cut all the way through at the ends
to represent individual boards.
And I like to stain those visible undersides
using some Minwax Early American.
And the first panel I want to glue in is panel A.
We're going to go in alphabetical order here,
trying to get glue in all the right places before,
you know, the glue on this end starts to set up just like that.
And it should line up
with the tops of the trusses, the roof trusses,
and the end should be more or less flush with the ridge beam.
We've already got glue on here.
Panel B is next, and that just fits right in there like that.
Now turn the whole thing around
and do the same thing on the other side with panels C and D.
And don't worry if there's a little gap up here
at the top of the roof, that's totally normal.
And then turn it back around and we do panel E
and the the smoke jack hole goes up at this end closest to the wall.
The next thing in the written instructions is building the cupola.
But we jumped ahead and did that in the last installment,
so I can kind of skip over the first part of that.
But one thing I want to do is sand down
these interior edges of these sidewalls so they match this angle.
So we get a nice fit in the roof opening up here.
Use my sanding block for that.
And now I can go ahead and install the three cupola rafters.
And just go down into the slots like so.
And each one overhangs the ends by about 3 16th of an inch.
The side with the slot is the front of the cupola.
So when we position the final roof panel F on here,
we want the hole for the boiler stack over on this side.
I'll get a good slathering of glue.
Try to get it on there as centered as I can.
Now, we don't want to glue the cupola into place just yet
because we need to run the hoist cable through here first.
And the kit comes with some number 10 crochet thread,
about 20 inches or so of it.
And before installing it, I want to paint or stain it a,
you know, a dark brown or black.
I'm just going to use my
dark gray stain marker.
And now with that stained, I want to tie one end off.
To the rafters or to the ridge pole right down here.
As I mentioned before, on a real mine, this cable would go down,
you know, through another sheave or a pulley system
down to a steam powered hoist,
which we located here in the back of the building.
Tie that off.
And I always like to put just a little dab of CA on there
for good measure to lock that in place.
And now I can run this through the slot
in the cupola, make sure that's getting straight.
Now I can run the cable up through the sheave wheel.
And since I glued this in place
so it's stationary, so it won't turn, I can now put a little dab
of CA in there to hold that cable taut like that.
We're not quite ready to
mount the ore bucket, the kibble down on the bottom.
So now I'm just going to put it to the side
and we can concentrate on finishing the rest of the roof.
The kit comes with four strips of this corrugated
roofing material from Full Circle Models.
And as you can see, it's already preprinted with a rust pattern on it.
And once it's installed on the building, it looks fantastic.
This is what I used for the roof exclusively on the pilot model.
But this time out, I'm going to change things up once again,
because I want this building to have its own personality,
a little bit different from the from the pilot model,
because also I want to show you what's possible, what variations
you can you can throw in there to make the structure your own.
For the roofing, I'm going to use tar paper rolled roofing
on the top of the bump out and the top of the cupola,
and then I'll do the rest with the corrugated roofing.
And for that rolled roofing, I'm going to use some good old
black construction paper and cut it into some three foot wide strips.
Now, this black construction paper is not included with the kit,
but, you know, you can pick up black construction paper just about anywhere.
Now I could use the construction paper just like this.
But I have found that if you paint it flat black,
you know, with just a basic rattle can paint,
it's going to look a lot better on the model.
Now, this bit of construction paper that's laser cut is the flashing
that goes around the base of the cupola.
And that does come with the kit.
And then I've got the laser board
flashing pieces that go around the smoke jacks.
And I'm going to paint all of this flat black at the same time.
While that paint dries, I can go ahead and cut this stuff
into some three foot wide panels.
It's already a prototypical eight feet long.
So I just need to cut three foot wide panels.
Now I've got my strips of rolled roofing.
I can cut those to length and we'll start here
on the bump out roof E.
And I'm cutting these a little bit longer
so it'll have a little overhang on each side and at the edge of the roof here.
For all of the roofing, I'm going to use some diluted white glue.
Diluted just enough so I can brush it on.
Bend it over the edges.
And let me show you a cool trick.
Works great if you paint the construction paper flat black
ahead of time like I did.
You can tear a piece off like that
and expose the lighter gray color underneath.
And it looks really cool.
In this piece, I want to lightly scribe it on the back
and fold it right there.
Now I want to locate where that hole was for the smoke jack.
Before I forget, I just push my pencil down through there, open that up
and we'll do the same thing on the cupola roof up here.
Fold that end over a little bit.
Do that again right there.
And for the last piece, I've cut this one to about two feet wide at scale.
We'll fold that lip
right over the front edge of the roof.
Now I can start on the corrugated roofing and right off the bat,
I need to do a little bit of trimming.
Cut a little notch out of that corner there to fit around the cupola.
I want to cut this here
and here to fit around the bump out.
Again, it's overhanging just a little bit, about 30 seconds
on an inch off the edge here.
We're off to the races.
So I'll just go down the line, cutting and fitting each piece
and overlapping the previous one by two corrugations or so,
which is about, you know, six scale inches.
When things start to get interesting is when you get here
and you have to work around this
this diagonal beam.
Best way I found is to lay the piece on here
and then just mark around it.
We're going to try to take out
that little notch right there.
I want a tight fit around here, but I also want some pieces
that are bent up around the base of those headframe beams
to act as sort of a flashing.
So I'm going to cut the hole a little smaller than I need it to be.
So I'll bend that up
so you can end up with something that looks kind of like that.
Just like that.
And then the next one, same thing, but from the other side.
And then we really don't have another issue until we get to this upright.
But this one's pretty easy to work around
since it's perpendicular.
OK, and I like that to overhang just a little bit,
just a few scale inches.
Bend it down like that.
And this side is a little easier
because you don't have the bump out section over here.
Now, with both sides of the roof done, I like to cap the roof up here
by cutting pieces that are about four
corrugations wide
and folding them in half longways like this, folding them over.
And then those get glued on the peak of the roof,
with each one overlapping the previous one by about a scale foot.
I think I want to put a patch right here.
An extra little square of corrugated material.
Maybe the roof was damaged and I had to put another one up there.
And then I'm using some of my leftover one by threes
to add some lath strips
to the top of these tar paper roofs.
This is something you would often see in
logging and mining camps
where they had these quickly built structures.
Basically put on there to keep the the tar paper
from blowing away in high winds.
Put those about four scale feet apart
and then I'll put a couple up here on the cupola roof as well.
This one I'm going to break.
Now I've got the flashing that goes around the base of the cupola
and those are pre scribed, so you just fold them on that scribe line.
Get some glue on the back
and just glue them into place like that.
I find it works best to do the sides first
and then on the ends you do a little cutting and fitting.
You need a couple of shorter pieces
and then cut this and then mark this angle
to match the angle here.
And I'm using diluted white glue to put these pieces on
and that kind of softens the construction paper.
And when you press it into place, you can press it in
so it conforms around the shape of these trim pieces here,
just like real flashing would.
And, you know, all of this is going to be dirtied up
and rusted up before we're done.
Now I get to open up the package of 3D printed parts,
which includes all of the characters.
Dealing with them in a little while and the boiler stack
and the smoke jack for the bump out,
which are the two pieces we need right now.
The bag also includes some UV resin and a small brush.
This is for making repairs.
If you break any of the the 3D printed parts,
just brush a little bit of this on, stick the piece back on
and you hit it with a an ultraviolet flashlight for a few seconds
and should be almost as good as new.
And with that in mind, I like to use a good quality
pair of sprue nippers like these and all those off of there
and then a little bit of cleanup with a fine emery board.
Just getting those sprue boogers off of there.
Once again, I want to add something a little bit extra to this model
that's not in the written instructions.
I want to have some guide wires on both of these smoke jacks
and to do that, I'm going to drill holes right through
using a size 72 bit in my twist drill.
I'm going to go straight through
and go right underneath this riveted band right here.
I want to do the same thing on this smaller smoke jack,
about three scale feet down from that conical top.
This smaller stove pipe is actually solid all the way through,
even though these are already printed in a flat black resin.
It's always a good idea to paint plastic parts anyway.
They're a little shinier than I would like.
So get some flat black on there after the flat black has dried.
Come back and dry brush on
sort of a medium gray over the top.
Bring out this rivet detail up here and then just at the very top
and dry brush on some Vallejo black.
And then down on the lower part,
I'm going to use my pan pastels at the dark rust tone.
I just want to kind of feather that up.
Now I'll get a clear matte finish on there to lock that in place.
Then I've got this laser board flashing
and I found the easiest way to do this
is to just thread the stack down through the flashing
and get it about where I want it to be on the roof,
right about there.
And I want to make sure those holes that I drilled
are lined up on this axis here when I put it in the roof
so I can run those guy lines.
Now I can glue this whole thing down into the hole
in the cupola roof.
Now I've followed all of those same steps
for the smaller conical smoke jack.
For the guy wires on my smoke jacks,
I'm going to use some of this K&S .016 brass wire.
Again, this doesn't come with the kit,
but, you know, you can pick it up at most hardware stores.
My local Ace Hardware carries it.
And I want to drill, again, a couple of holes
to receive that wire in the roof.
And I think what I'll do is just go ahead and install these
and then paint them in place.
A little dab of CA on that end.
Put that into the hole that I drilled.
The other end, go down into this hole.
And we'll do the same thing up on this one.
This wire bends super easy
and you do want to try to keep it as straight as possible
if you're going to do this.
Put a little bend in that end.
I'm going to glue this in.
Put that down in the hole.
And there we go.
And now I'll just paint those with some Vallejo black.
Now it's time to build the mine shaft cribbing.
And that indicates the opening of the mine
right down here directly below the sheath.
And for that, we've got some laser cut pieces.
These are cut from some 316th of an inch thick basswood,
just like all of the supports for the head frame.
And these go together almost like Legos, you know,
just boom, boom.
Pretty, pretty simple.
But before I put these together,
I want to add a little wear and tear.
I'm going to take my sanding block
and kind of wear that away.
And this is what would happen, you know,
pulling that ore bucket, that kibble as we're called,
up and down from the shaft.
You'd have a lot of wear and tear.
And then I'll touch up the stain there a little bit.
And now this goes here.
And then this one goes here.
And now I don't want to glue this front piece in just yet.
You see how these side pieces have these extra long gaps here.
That's to fit over this front beam of the head frame right there.
So it all locks into place.
And you might need to do a little bit of sanding
on one side of this to get a good fit.
But I can put some glue here and here.
And that's going to fit right there between those battens.
And now it's really easy to glue that final piece in just like that.
Now let's take a look at the rest of our 3D printed parts
and the characters that come with the kit.
Now we've got two different ore kibbles or ore buckets.
I've got a newer iron one and an older beat up wooden one.
We've got two hooks.
You only need one of these.
But there's two in there just in case you break one.
And that's going to go on the end of the cable there.
And then we have these three figures.
And these three figures are included with every kit.
You've got the guy climbing the ladder.
You've got old Jeb here chopping wood.
Got to keep that boiler going.
And then you've got the miner who's actually holding on to the cable
and standing on top of the ore kibble.
And this is from a historic photo that Scott found and it was just great.
We have to do that.
So this guy's really cool.
And he's got, you know, the traditional late 19th century miners derby.
They would take just regular derby hats and they would harden them with paraffin.
And then he's got a little, you know, his little lamp right there.
Oil lamp on the brim there.
He's getting ready to go down into the shaft.
But there is also a companion pack that you can add on that comes with four more characters.
You've got this guy who actually rides down inside the ore bucket.
Also taken from a historic photo.
And we have this guy, another miner, looking down into the mine shaft.
And then there's the guard with a rifle and his dog.
And this rather important looking fellow who's got a bag,
which presumably is full of gold ore.
Maybe he's taking some samples down to the assay office.
And right now I'm going to finish removing the sprues from all the rest of these guys
and these pieces here, these buckets.
And we'll get some primer on all of this and finish up detailing the mine.