This is the second of a three part build of the Gold Tooth Mine, and in this installment, I show how to build the board and batten walls; the doors and windows; and add a weathered paint job that evokes structures of the late 19th Century. Plus, more tips and tricks that aren't in the instructions!
The first kit from Thunder Mesa Kits is now available and it's the Gold Tooth Mine in 1:48 scale! At the time of this recording, there are still a few kits available but these kits are only being produced for a limited time. https://www.thundermesakits.com/
Thanks for watching, Dave ____________
Become a Thunder Mesa Member on Patreon for early access, exclusive content, and members only parts and details from the builds! https://patreon.com/thundermesa/
All music courtesy YouTube Audio Library, Creative Commons License.
AI Generated·May contain errors
Video Summary
AI Generated
This video is the second part of a series on building the Gold Tooth Mine kit. The presenter, Dave, demonstrates advanced techniques for wall preparation, board and batten installation, Victorian-era painting, and the addition of intricate architectural details to create a realistic, weathered scale model.
Howdy, folks. Dave here for Thunder Mesa Trains.
Welcome back to the studio where today we're going to pick up
right where I left off last time with the Gold Tooth Mine Build.
This is part two in a three part series on the Gold Tooth Mine.
And that's the new kit that's available from Thunder Mesa Kits.
You can check them out.
There's still some available over on ThunderMesaKits.com.
And in the last installment, we built the entire head frame.
This time out, I'm going to be working on the walls,
the doors and windows, the board and batten siding and the overall paint scheme.
A lot of ground to cover.
So let's jump right in.
And here is that head frame that we built in the last installment.
This is basically the bones of the entire structure.
Right now, I want to set that aside because we're going to dig back
into the box and pull out all the pieces for the walls of the structure
and for the doors and the windows and get all those prepped and ready to build.
Now, in this large bag, we have all of the wall pieces.
Go ahead and pull those out of here.
These chipboard pieces are for the roof.
We're not going to be using those just yet, so we'll leave those in the bag.
We'll get all of these basswood plywood pieces out.
Now, this is some one sixteenth of an inch thick basswood plywood.
It's very sturdy and strong material.
I really like using it for the walls of structures like this.
The figure six on the plan identifies all of these pieces with numbers.
So let's go ahead and sort them out.
This is piece number one.
This looks like two.
This is three, four.
This little comb shaped piece is number five.
And then I've got three three by six floor joists.
That's number six.
And then we get to the bump out section
with seven, eight, nine.
And then the cupola pieces, you've got 10,
11, 12 and 13.
Now, you can see on here, the doors are actually part of the wall here.
They're laser cut and laser etched right from the wall piece.
And if you wanted to model these open, you just cut through
these little tabs right here and you can glue those doors
into any position you want, open or closed.
But right now, I think the first order of business
is going to be to distress this wood and get some stain on it.
As I usually do, I'm enhancing the grain
on each of these etched boards
with the blade of a fine tooth razor saw going with the grain,
just deepening that that
wood grain a little bit.
Sometimes it helps if you twist the blade.
Makes it look a little bit more natural.
And you can see I do one board at a time.
And of course, I don't want to forget
to do these scribed boards on the doors as well.
And I also like to take my nail tool,
which is just a track nail and a little pin vise here
and add some knot holes on some of these boards here and there.
And those will pick up the stain and look very nice.
And for the stain, I'm going to use the same mixture
I described in the last installment.
This is my shoe dye and rubbing alcohol stain.
Makes a nice silvery gray when applied.
And on wall pieces like this, I always want to stain both sides.
And that's to even out
the tension on the walls
as the stain dries and it keeps the pieces from warping.
And now I want to let all of that dry for, you know, at least a couple of hours.
And I'm going to throw you guys a curve ball right off the bat here.
Surprise, surprise.
I'm going to deviate from my own written instructions right now.
I'm staining the one by six trim boards
and the one by three battens for the boarded batten siding.
Kind of jumping ahead to do that.
The instructions call for you to now basically assemble
the four walls of the structure around the head frame
and then to add the battens for the board
and batten siding after all of that is done.
And you can certainly do it that way.
I did it that way on the pilot model, which is why the instructions
are written that way.
But this time, what I think I want to do is do most of that work
on the walls while they're flat.
I want to add the battens to the walls while they're still flat.
And I think paint them, too, before I install them on the structure.
So I'm skipping ahead a little bit, changing things up
mostly because I want to show you that,
you know, there's more than one way to skin a cat.
So to apply the battens to the walls,
first, you need to cut some off of the sheet.
You can either cut them off one at a time or all at once.
It's up to you.
I tend to like to do it one at a time.
That way I don't lose parts.
And I want to apply a little bit of glue to the back with a toothpick.
Again, I'm using some Titebond
yellow carpenters glue.
And then you lay these right on top of the scribe lines,
which indicates, you know, where those two boards come together.
I always like to leave a little bit of a gap down here
at the bottom of the wall, you know, about a sixteenth of an inch or less.
That's prototypical.
You see that on a lot of old board batten structures.
And then once that's in place, the glue is set up, I turn it over
and cut it off right at the roof line.
Makes that really super easy.
And using the cut off from that same piece, do the next one.
And on down the wall we go.
I'm going to put battens everywhere except on the corner edges,
because that's where that one by six trim is going to go later on.
I also want to show you on this front wall here,
this is wall number one on the plan.
I don't want to put a batten here yet
because this is going to go right behind this upright.
And I'm going to wait until that's glued in place
and then I can use a piece to trim that off right there.
And then when I get all the battens in place, just take my sanding block
make sure that's nice and smooth there and won't interfere with the roof later on.
And that's basically how you do the end gable walls.
But for the sidewalls, things are a little different.
On the sidewalls, I want to leave a little space
and create an allowance here for the one by six framing
that's going to go around the doors and the windows.
I'm not going to add it at the same time as I'm doing the battens
because I want the window and door trim to be painted a complementary color.
So it's a lot easier to wait until after the walls are painted
and then paint the trim separately and then apply it.
Then the instructions call for you to measure out one eighth of an inch
all the way around the doors and windows, because that's the width
of the one by six framing.
A really easy way to do that is just take a piece of that
that one by six trim and lay it on top.
I'll line it with the bottom or the side of the door and window.
And then I'm using a sharp, hard lead pencil
and just putting a faint line right there.
And that's going to tell me
how far I need to come up with the battens,
but, you know, not go too far to interfere with the the window frame.
And I'll do that around all of the doors and windows.
On the doors, you notice there's an extra wide gap around there.
You want to take that piece of one by six trim and line it up
with the inside of that gap.
Just to be on the safe side.
Now, when I apply these battens to the side walls,
I want to leave about a sixteenth of an inch gap
at both the top and the bottom.
And the one at the top is to allow for the slope of the roof
when that is installed on there.
And here at the tops of the walls, you also want to leave a gap
below the rafter notches, because when those
roof trusses are installed,
you want to leave allowance for the rafter tails coming out.
Now, I just want to show you a couple of things on this particular wall.
This is wall two in the instructions,
and this is where the bump out shed is located.
So that means you don't need any battens in here
from this line right here next to the slots all the way over.
You don't need another one until right there.
And that's because this is actually an interior wall in this case.
And the other thing I wanted to show you is, you know, don't be afraid to
leave some gaps or, you know, have some of the battens
be broken here and there or missing even.
This is a building that that works for a living,
and that wear and tear should be evident.
Wall number three here is a good example of everything I've been talking about.
A little space left at the top and the bottom of the battens.
Allowance, 1 1⁄8 inch allowance around
the windows and doors for the window and door frames.
No battens on the ends where the trim is going to be.
And last but not least, some broken and missing battens here and there
just to make it interesting.
And then on wall number nine, which is the front of the bump out section,
you really don't need any more battens than that.
Because of the trim, it's going to go around the door and the window
and on the corners.
Now with the battens done, the next thing that's called for
is to do the Z bracing on the doors.
You've got the two man doors and then you've got the two sets
of big freight doors on each side.
They're all the same.
I'm going to use some one by six to do this.
There's some scribed lines here, so it makes it really easy.
Lay a one by six on top.
Mark the end and cut it.
Cut the bottom one the same length.
So I do the top and the bottom braces first.
Glue that right on top, lining it up with the scribe line
and one down here.
Now I can lay another piece of one by six on top here
and mark where I need to cut
for this angle there.
And now I can glue this on again,
lining it up with those scribed lines
and a detail that always looks real nice
is to do some nail holes on here
to do two per board.
And if you don't have a fancy homemade tool like this,
you know, you can you can just use a dress pin to do this
or a track nail.
There you go.
And now I'll do all the rest of the doors the same way.
Now, with all of the battens installed and the Z braces in place,
these walls are now ready to be painted.
Notice that the cupola walls up here do not have battens on them.
Of course, if you want your structure to be unpainted,
which is a totally legitimate choice,
you're you can stop right now.
A lot of these old mine structures were never painted.
But I mean, I do want to have some paint on mine.
And that brings us to the discussion of color.
When I built the pilot model, I went with a very traditional
sort of red oxide color on on the main body of the structure
and then used a lighter tan for all of the trim pieces.
And that's what's described in the written instructions.
And it's you know, it's great for most eras that you might be modeling.
But today, this one I'm building now,
I think I want to try something a little bit different.
My boomtown of Latigo exists
in the late 19th to very early 20th century,
basically what's known as the Victorian era.
And that was a very interesting time because on the one hand,
you know, the way people dressed was extremely conservative,
blacks and grays and, you know, with white shirts
for the most part.
Maybe maybe a woman would wear a blue dress once in a while.
But it was a very, very conservative time as far as clothes were concerned.
But structures and machinery, particularly steam
powered machinery, was often very brightly and elaborately painted.
So to reflect that era in my version of the gold tooth mine here,
I think I want to paint the walls sort of a muted gold color,
not quite buff and not quite yellow, basically a yellow ochre.
And I'm going to use some artist's acrylics for this.
We'll thin them down with some matte medium
so I can brush them on the walls and it won't go on too thick.
And just a word of caution.
When painting a structure green or yellow,
those two colors, for some reason, it's very easy to get those wrong.
It's very easy to get them too bright and oversaturated.
So you always want to err on the side of earthier tones
and more desaturated colors.
And I think this this yellow ochre will work pretty well.
And then we'll come back and do all the trim in that red oxide.
And that should make for a very distinctive looking structure
that that reflects that Victorian era.
So I've squeezed some of that yellow ochre into one of my lids here
and mixed it with some matte medium to thin it out.
And I'm just going to brush it on using a flat brush.
One thing you want to watch out for
when painting structures with board and batten siding
is the paint building up around the battens and globs,
especially if you're using acrylic paints like I am.
Now, when I get down to the bottom here, I start at the top
with a fully loaded brush.
And by the time I get to the bottom of the wall,
a lot of that paint is gone.
So I'm kind of almost dry brushing by the time I get down here,
which is ideal because that reflects how structures like this weather
with, you know, rain
bouncing up, splashing up onto the bottom of the walls
and wearing away the paint.
And I always want to go with the direction of the wood grain
when brush painting wooden walls like this.
And then just as soon as that paint is dry to the touch,
come back with a wire brush like this.
It's a stainless steel wire brush.
And again, going with the grain,
you're going to scrape a lot of that paint off.
And again, paying more attention to the bottom of the walls down here.
This makes a subtle difference, but it does make a difference.
You can also see why we bothered to stain the walls first.
Some people have asked me, why do you stain the walls first
if you're just going to paint them?
Because you want that that stain showing through
the color that you put on top of it.
And then I'll take the flat edge of my hobby knife
and go over some areas again, take a little bit more paint off,
especially around doors, places like that, high traffic areas where,
you know, the paint would naturally wear away.
One thing to note in the instructions,
it mentions going over all the walls again with a dark wash.
And that works great with the red oxide walls.
But I would not recommend it with a lighter color like this.
It'll it'll completely throw the tone off.
So you want to leave well enough alone at this point.
What I do recommend, though, is dry brushing on some light tans
and grays down along the bottom of the walls.
Show that wear and tear and
rain splashing up, splashing dirt up on the walls.
Now, with those walls done, I can turn my attention
to the stenciled lettering that goes on
each side of the of the cupola.
And the kit comes with a pair of stencils
which are designed to fit
right on top of those walls like that, flush with the bottom and the sides.
These are parts 11 and 12, by the way.
So what I want to do now is spray the backs of these stencils
with a low tack spray adhesive.
You might get away with using double stick tape, too,
but it's probably a little too thick.
You don't want anything quite that thick on the back.
A low tack spray adhesive like photo mount is going to work the best.
If you don't have that, I would recommend just taping it
around the edges as tight down on there as you can.
The spray adhesive just makes sure that it's it's right on top of there
and paint isn't going to, you know, get underneath the stencil.
You don't want these to be too tacky
because then you might not be able to get them off.
You don't want to permanently adhere the stencils to the walls.
So you can dab some of that adhesive off if you need to.
Put the bottom
and the side edges.
You really want to make sure that's straight.
Nothing looks worse than stenciled letters that are crooked.
I'm just going to tape off the rest of this masking tape.
In fact, I will tape them down completely
to this piece of cardboard, masking all the edges.
Now I'll just do a little rattle can, basically some antique white.
I want to go pretty lightly over this, not get carried away.
That's probably good.
And now, while I'm waiting for that paint to dry,
I can leaf back in the instructions to the place we jumped ahead from
and start gluing these walls onto the head frame.
This one fits behind
the uprights just like that.
That's wall number one, and that's the one we want to glue on first.
So I will apply some glue to these mating edges
and inside the cutout areas that fit around the beams.
And then this goes here.
Just like clamp that in place with my fingers
for a minute or two until that glue sets up.
Now I can put on wall number two.
And for that, I want to apply glue
to the sides of these head frame beams,
every place that they're going to mate up with the wall.
And we'll put some on this edge here also.
Little clamps like this are very handy.
Got these from Micromark, but you know what also works really well?
Clothespins. You can pick those up just about anywhere.
And the same thing with wall number three.
Make sure that's flush with this bottom beam.
And wall four
drops into these tabs and slots on the end.
Just like check back in on our stencils.
See how the lettering turned out.
Let's peel these off of here.
All right. Not half bad.
So the main part of the mine would likely have a dirt floor
in here, but this little bump out section,
I created some floor joists and a wood floor for that.
Maybe that's the office.
So the assembly on this is very straightforward.
Basically, you've got this comb shaped piece, which is the the bottom
and these three by six floor joists,
which glue right on the top of it.
And you can see there are scribed lines here to show you exactly where those go.
Dab of glue on each one of these.
Just like that.
Now we've got this opening down here at the bottom of the wall
and the completed floor joist assembly
gets glued right into that
that space, that little slot there.
Now I can glue in the sidewalls of the bump out, which are parts seven and eight.
Those fit right into those slots.
I'm going to make sure we glue it down to the floor joists as well.
Now, in this bag with the
the windows and things, you'll also find the floor for that little bump out.
Some one thirty second of an inch thick scribed basswood.
And it's a lot easier to put that in now before I put that front wall on there.
But before I put it in, I want to stain it.
I'm going to use one of my stain markers here.
This is some Minwax Early American.
Now I'll get some glue on the tops of these floor joists.
If you wanted to detail the interior of this little office
bump out, now would be the time to do that.
They look pretty cool with a potbelly stove in the corner right over here,
because that will line up with the smoke jack that's going to go up here later on.
The front wall of the bump out, that's wall number nine.
Before I glue this in, I want to I want to model this door partially open.
So I'm going to cut through these hinge tabs right here.
Now I'm going to sand slight bevel
into that edge and then glue the door back in there.
Just a slight open position.
There we go.
Now I can line up all of these tabs
and slots and glue that into place.
Now I want to trim all of these corners
using mostly these these one by six pieces.
I like to start on the the end
peaked walls, mark where to cut
and then glue that on there flush with this edge.
And I'll come back and paint all of these trim boards
the same color as the walls once they're all installed.
And I'll use the other half of that trim piece
over on this side.
And then I add another piece
on the sidewall here, overlapping at the corner.
And that's going to cover up
those tabs and slots.
Note that you also want to cut this one
a little shorter right there
because of the notch for the the roof truss.
So it won't interfere with the rafter tail coming out.
And the same thing
on the bump out section.
Again, note up here where I left space
for those rafters to stick out.
And here on these inside corners
where the bump out meets the main wall,
I've just added another
piece of one by three there to trim that out.
I'll show you up here on the front.
Use a one by three right here for the trim
next to the head frame
and then a one by six on the side.
You want to use a one by three here
because a one by six won't fit.
Now I'll go back and paint
all of those trim pieces with the same color
I used on the body of the structure.
And I'll replicate
the dry brushed weathering as well.
Let's see, we did that.
We did that.
That we did that.
We did this.
Ah, window and door trim.
That's next.
The instructions give you the number
and the dimensions of all of the pieces
of one by six
that you need to cut for the door
and window trim.
And that's so you can cut them all
ahead of time and paint them
a complementary or contrasting color
if that's what you want to do.
And I do want to do that.
So I'm going to follow this.
I need for the doors.
I need 10 pieces that are 1.75
inches long, one and three quarters
and two pieces that are one inch long.
And then for the windows,
I need eight of the one by six pieces
that are three quarters of an inch long.
Now, this isn't in the instructions,
but I'm going to go ahead and
preassemble
the two window sills
by gluing that one by three
on top of the one by six.
And that way I can paint it
all at the same time.
Next, I want to cut out
the window frame pieces
from the twenty five
one thousandth of an inch
thick laser board sheet.
And these consist of an inner
and outer window frame
so you can model
the windows open or closed.
Now I've set all of these pieces up
on some cardboard for painting
because I'm basically
going to just rattle can these.
And the color I want to use
is this Rust-Oleum Red Oxide Primer.
While I wait for that paint to dry,
I'm going to jump ahead again
and preassemble the cupola.
And this is a good example of why you
you want to read through
all of the directions
on a kit before you start,
because there will often be little
subassemblies like this
that you can knock out
while you're waiting for,
you know, other paint to dry
or glue to dry or something like that.
It's usually not described
that way in the instructions,
because the instructions
in order to be clear
have to be, you know, pretty linear.
But if you if you already know them
and understand them,
then, you know, you can jump ahead
and say, oh, well,
I can go ahead and do this now
because, you know,
that'll save me a little bit
time, a little bit of time later on.
Now, the four walls here
only really go together one way,
so hard to mess this up.
Only thing is, you have to make sure
that it's all it all goes together
very square
so that will fit on the roof
properly later on.
Line this up
with my cutting mat,
make sure it's going together
nice and square.
And I pre-cut all of the trim
pieces for the cupola.
Go ahead and pre-paint those.
My yellow ochre.
This just makes a little cleaner job.
I don't want to
mess up my nice stencil work.
And once again,
I want to put the end pieces on first.
I cut it so it wouldn't interfere
with the rafter slot up here
and then the sides.
Now that the paint is dry
and all those pieces,
I can go ahead and pre-assemble
the windows.
And look at that, we're on page
eight of the instructions already.
And the kit comes with some
laser cut acrylic
for the window glazing.
I want to remove the tape
and the film from this.
The masking tape is on there
to keep from
scorching the acrylic
during the laser cutting process.
And then it also has a protective
film on it
to keep the fingerprints off.
I'm only going to remove
the tape and the film
from one side at a time.
And that way I can glue
the glazing in place.
And then when the glue is dry,
take the the film
off of the other side
and that will really cut down on
fingerprints and things like that.
I like to use this
ZAP 560 formula
canopy glue for
any kind of glazing like this.
Works great.
Just want a thin film of it
inside of the frame.
Push that down into place.
Now, usually when you pull
the tape off,
it's going to pull the film
off with it.
That's what you want.
You can always tell
if you just touch
the back of the tape
and if it's slick
instead of sticky,
you know it pulled the
the film off along with it.
You know what I forgot to do
is weather these window frames.
Ordinarily, you want to do that
before you put the glazing in,
but now I have to do it
very carefully.
With the glazing in place,
just going around the edges,
dry brushing on a little bit
of that same light tan
that I used on the walls here.
And now with that done,
I can go ahead and remove
the protective film
from the backside of the glazing.
Now I can glue the lower frame
to the upper frame
on the inside.
Again, you can do these
open or closed.
Now the inner sashes
of the window have
a thinner side
and a thicker side.
Just FYI, the thicker side
goes on the bottom.
Now I'll put some yellow glue
around the inside
of these window openings.
And glue these into place
on the structure.
Now I'm going to pre-weather
all of the door and window trim.
Not going to forget this time.
Using that same light tan
and just dry brushing it on.
Remember my number one tip
when it comes to dry brushing
is there's always more paint
on your brush
than you think there is.
And now I want to trim
the sides of the doors
and windows first.
Bring that trim right up
to the top of the door
or window opening.
And then you can put that
top piece of trim on there.
And on the windows,
same thing.
And I like to overlap
the edge of the window frame
just a little bit with the trim
and the top
and then the bottom
with that window sill.
And if you measured
everything right,
it should fit
right in between the window
and those battens.
On the big freight doors,
same thing.
Sides first
and then one across the top.
And conveniently,
these are all 1.75 inches long.
So you don't have to keep track
of which are the sides
and which are the top
on these big doors.
It doesn't matter.
They're all the same.
The reason you want to do
the sides first
is so that the ends
of the top will line up
with the side trim on the doors.
And on the two man doors,
it's the one inch piece
that goes on the top.
And on this back wall,
you might have to trim things
just a little bit
to fit in between the battens,
but it's no big deal.
OK, now I'm ready
for the door hinges
and the door handles.
And the door hinges
are all located on
the same laser board sheet
that the the windows were on.
And the door handles
are on the same
16th of an inch
thick MDF piece
that the the sheave
blocks were cut from.
And I'm going to paint
all of these pieces
a dark reddish brown.
And then once the dark
brown is dry,
I just lightly dry brush
the hinges
to bring out the detail.
Bolt heads and the actual
barrel of the hinge
are etched right in.
And we'll do a little bit
on the handles, too,
to indicate some wear and tear.
And just a little dab
or two of glue
on the back of each hinge.
And those go right here like this.
The square end
on the door frame
and the pointy end
on the Z-brace
of the door.
One at the top
and one at the bottom
on each door.
For this door
that's partially open,
take the hinges,
turn them over,
scribe across the back
pretty much opposite
where the barrel is.
You don't want to cut
all the way through,
maybe about halfway.
And then I can easily
bend that
at that scribe mark
to fit the angle of the door.
So it's going to look like that.
And for the door handles,
I want to measure up
three scale feet
from the bottom of the door.
That's
three quarters of an inch
to you and me.
Draw a little mark there.
And a couple of small dabs of glue
right out near,
but not quite flush
with the edge of the door.
The window shades are not
included with the kit,
but it's a really
simple detail to add,
especially if you've got
some green blotter paper
like this laying around,
which I just happen to have.
This is from a file folder.
I'm going to cut a couple of pieces
which are about
half an inch square.
Now I can add a little bit of glue
to the inside of the wall
right here, right above
the window.
And you can just take one of these
and press it into place.
And same thing on the other window.
And that seems like a pretty good place
to wrap this video up.
I will be back in two or three days
with part three of the Gold Tooth Mine
kit build.
And that's when we're
going to be doing the roof
and the figures and all the details
and the final weathering on the kit.
Hope you'll stick around for that one.
And I hope you're subscribed
with those notifications turned on.
So YouTube will let you know
when the next video is coming
from Thunder Mesa Studio.
And until then,
you can also follow along
for free on Patreon.
That's at Patreon.com
slash Thunder Mesa
or on Instagram at Thunder.Mesa.
And check out the resources
available on the Thunder Mesa
Studio website
at ThunderMesa.Studio
and the kits available
at ThunderMesaKits.com.
As always, a huge thank you
to our Patreon members
who helped to make
all of these projects
and all of these videos possible.
Until next time,
keep moving forward, everybody.
Adios for now.