San Lorenzo Mini Layout | On30 Track and DCC Wiring

ThunderMesaStudio
139 followers
183 Video Views·Dec 30, 2024
[Music]
Howdy Folks Dave here at Thunder Mesa
Studio where this week I want to bring
you up to date on what's been happening
with the om30 San Lorenzo mini layout I
first introduced this new project in a
video at the end of November and if you
happen to miss that one of course you
can check it out at the link but in a
nutshell what I'm doing is taking the
original structures and figures and
scenery items from Burn Niners San
Lorenzo diarama and incorporating them
into a 2x4 foot mini layout sadly we
lost Vern a few years back and I'm
hoping this you know this little mini
layout will pay homage to him and his
wonderful o30 australa and sonar Grande
layout so what I hope to accomplish this
time out is to get all of the track laid
and everything wired up so we can
actually get some trains running on this
thing so without any further Ado let's
get
started I've gone ahead and removed all
of the structures and everything else
that was on here temporarily because the
first order of business today is going
to be running some wiring underneath the
layout deck for the DCC system and the
easiest way to do that is to take this
whole thing and flip it upside down
I like to use a 14 gauge wire for this
some people like it a little heavier
some might like a little lighter I like
14 gauge because uh you know it's still
flexible enough to bend you know easily
around corners and things like that you
want a pretty heavyduty pretty robust
wire for DCC systems because they they
carry more current than you know good
oldfashioned DC and um the reason we
want wiring all the way around under the
Mainline is so that we can drop feeder
wires down from each individual section
of track I'm going to be using you know
meter long Flex track
sections joined by uh nickel silver rail
joiners but you don't want to count on
those rail joiners to carry the current
from one section of track to the next so
that's why we do a DCC bus it just uh
makes for much more reliable operations
in the long run those rail jointers can
fail you could have a bad solder joint
you know many reasons why uh you don't
want to depend on those exclusively for
electrical contact so it's just a good
idea good practice even on a small
layout like this to run a DCC wiring bus
and I'm going to show you exactly how we
do that so I'm going to thread the wires
through these uh 1x3 cross beams and you
know the wiring doesn't have to be
directly perfectly underneath the track
but you know if you can get in in the
neighborhood that's uh that's pretty
good now I could get away with just you
know putting one hole and threading both
wires through there but I'm doing two
holes because I want a little bit of
separation between the inside wire and
the outside wire just to keep them
nicely organized so this hole will be
for the outside rail the outside wire
this one will be for the inside rail the
inside wire so will go red and this
through this hole and black through that
hole it'll just keep things every you
know nice and
organized all right let's see this is
the
front yeah so I decided the power is
going to come in from this side so we'll
start over
here R this through the holes
over
here where the wires are going to run
underneath where the bridge is going to
be there's going to be a little Royo
here I'm just going to use my staple gun
and uh tack the
wires like that
and do the same thing with the black
wire taking great care of course not to
put the staple through the
insulation but on one side and the other
and I'll go ahead and Tack them down at
this end
also okay I haven't decided yet
exactly where the control are going to
be so get myself plenty of slack
here then just run the wires out through
this
hole
temporarily now you don't have to close
this circuit you know by
um by wiring this Loop
together but I'm going to go ahead and
do it anyway because it makes for a
neater job take a little bit of
insulation off
here matching up the 14 on my uh
strippers with 14 gauge wire peel this
insulation off a little bit about a
about a half an inch of it take a little
bit off the end of
this we'll splice these together
using some
6040 Rosen core lead solder here and
we'll just wrap those
up with some electrical
tape and that's a good warm up up for
all of the soldering
jobs that are left to do on this there's
going to be quite a few and there is
your DCC wiring
bus now I can turn the whole thing over
and uh and start laying some track and a
comment on the previous video somebody
said they they actually cringed when I
covered up my track center lines with
this cork because how then would I know
where the track is going to go
uh on a small layout like this it's
really not that big of a deal and I'll
show you exactly why now on a small
layout like this I almost always want to
start by laying the track on the curves
because that pretty much determines the
geometry for everything else now I'm
using microengineering Flex track code
83 Flex track and this layout is
designed with two 10in radius curves and
I've drawn out the center line of a
10-in radius curve on this uh you know
this scrap piece of
Masonite one of the things I really like
about this microengineering Flex track
is that it will hold just about any
shape you Flex it to which cannot be
said of all brands of Flex track so I'm
going to use this as a template and just
bend this track to that 10in radius
there we go and you can see here that
bending that sharp curve has smooshed
two of these ties right up next to each
other that doesn't look very realistic
so the first thing I want to do is
remove one of these
ties before I go to lay the
track cut through the
webbing there we
go that gives that uh that rail a little
bit of breathing room and then that is
going to go right
there now I do have some marks on the
road bed here I've measured in 2 in from
the edge in a few places and put a
little Mark to show me where the center
line should
be but I'm just going to let the track
kind of naturally find its own Center
Line and just use
those you know as a general guide one
advantage of having such sharp curves on
this is that I can get the whole thing
with one you know 3ot long piece of Flex
track I don't have to solder two pieces
together on a curve which is always
challenging and and can you know lead to
some weak joints if you don't do it
exactly right I honestly don't
remember how Vern laid his track on the
Australian sonor Grande I think he used
glue think he glued it down but I'm
going to use my preferred method which
is rail spikes right through the ties uh
and right where the rail spikes would go
if I was uh hand laying the track these
Micro Engineering ties are kind of a
hard plastic so you have to drill a
little pilot hole we got a size
65 bit
in my uh pin
visce draw a little pilot hole and then
just uh use my uh zeron spiking tool to
drive in some microengineering small
rail
spikes right next to where the cast in
spikes are and I do that about you know
every one two three four five six tie or
so on a curve Less on a straight piece
of track just enough to hold it down
doesn't take take
much we drill a little
hole just through the tie you don't need
to go down through the road bed position
the spike and the pliers like
so and we'll push that home once the
track is painted and
ballasted you won't see those spikes at
all they'll just blend right in
even though they're a little bigger you
know than the the cast in Micro
Engineering spikes which are scale by
the way so these are about three or four
times the
size and we do one on each
side just like
that on we go all the way around the
curve
[Music]
all right so I finished spiking the rail
around this
curve and now I'm coming into a straight
section here and usually I don't solder
the rail joints on straight connections
and that's to allow for expansion and
contraction of the rail seasonally you
know during during changes of
temperature because this nickel silver
rail will expand and contract quite a
bit but in this particular case I am
going to solder this connection right
here because I need to put a little bend
a little twist in this short piece of
Flex track I've cut a piece about six
inches long and I need to flex it a
little bit to made up with the turnout
and bring these bring this back into a
alignment originally when I drew this I
drew this you know straight parallel to
the edge of the layout but uh that's
kind of boring to look at actually so
I've built in a little bit of a you know
a little bit of a wonky curve here and
that's just to make it more interesting
let my soldering iron get good and
hot and uh now I'm going to put a little
bit of uh no clean flux on this
joint make sure I've also made sure that
these rails and
these
um rail connectors are very
clean I'm going to use the same
6040 Rosen core solder here make sure
that's lined
up that's plenty hot yep heat the
joint and put a dab of
solder you can use the tip of the
soldering iron to spread that
out just like that now the inside rail
is always a little bit trickier
here that cool for just a
second all right now I can Flex this
piece
around put a little Bend in it so it'll
align where the turnout's going to be
without that rail pulling out of the
rail Joiner I can go ahead and Spike
this piece down by the way when I push
these spikes in they're going all the
way down through the tie through the
Cork and just the
tip is going into that plywood so you
have a nice strong hold there just trim
up just a little bit of that
rail remove this
tie
out now on this joint going into the
turnout I won't solder this one and
that's to allow for that expansion and
contraction that I was just talking
about but before I permanently affix
this turnout in place I need to do one
slight modification to it this is a DCC
ready microengineering
turnout and what that means is that the
frog is isolated you see there's gaps
that there and gaps right there so this
is dead there's no power coming to
through the rails to this frog and that
prevents a short on DCC systems it also
means that short wheel-based locomotives
like quarters and things will stall on
turnouts like this so what I need to do
is power this frog
somehow uh and the easiest way to do
that is what I'm going to show you and
while I have the soldering iron nice and
hot I'm going to connect a wire there's
a little little nub right there you see
that that's so you can solder a wire in
there and power that
frog and uh when we hook everything up a
little bit later on I'll show you
exactly how that works right
now just want to Tin this wire this is
some U 28
gauge wire that like to use for track
hookups just adding a little bit of
solder to the end of
that some uh turnout you get will
already have a little little piece of
wire soldered on to
this this one does
not so got to do it the oldfashioned
way there we
go now connect the two together
shouldn't take more than a
touch okay got a nice strong
connection I need to
Mark exactly where that
is so I can drill a hole
that's better yeah all okay now we can
Spike the turnout down on turnouts like
this I like to put a couple of spikes
down at the point
end uh
couple you know up here by the Frog
oops and then a couple more at the
diverging end
now here where the track is coming out
of the turnout I'm not going to solder
these rail joints once again that's to
allow for that expansion and contraction
of the Rails seasonally but I have
another joint up here that I am going to
solder and just real quickly I I'm not
gapping the rails here where they come
out of the turnout and that's because
this is a a dead frog turnout at least
it'll be dead and until I route power to
it and on the Pico turnouts Pico 030
turnouts that I've used in other places
on the Thunder Mason layout stuff like
that you do need to Gap at this end uh
anywhere the power is coming from the
from the diverging end of the turnout to
prevent a short circuit but since this
is a dead frog or will be a power
routing frog I don't need to worry about
that
now I can bring this
around to the proper
radius and uh spike it down while I'm
still over here working on this side of
the layout go ahead and put the spur
track in
also okay now I could just flip the
whole thing around and finish up the
track on the other side
now since there's going to be a bridge
over here on this side it's you know
it's pretty important
that this is at an accurate and
consistent 10in radius because you know
that's going to make the bridge a lot
easier to build than if it's you know
fluctuating all over the place so uh to
facilitate that I've cut a cardboard
template here to a 10-inch radius that's
what this Center Line is is so I just
need to make sure that the track is
aligned on that Center Line got it
propped up here with some foam while I
Spike down the other end right here if
you watched the previous episode of this
build uh you might remember that
originally there was
um a piece of road bed here that would
have been underneath the bridge
temporarily it would serve the same
function is this this piece of cardboard
here um but I ended up cutting it out
because it had gotten all chewed up
while I was uh cutting out the road bed
and this is just you know this just goes
to show that there's there's always more
than one way to skin a cat there's more
there's more than one way to do
something all right that just leaves us
with one final piece of Flex track to
lay to complete the loop
[Music]
[Applause]
[Music]
n
this is the final
Spike maybe I should paint it gold
[Music]
huh and with that the final piece of
track is laid so you know I think I'll
come back tomorrow and we'll wire
everything up and see how it runs now
I'm soldering on some feeder
wires to each one of those sections of
track a red wire for the outside Rail
and a black wire for the inside Rail and
I'm using some uh 28 gauge solid core
wire which is my favorite for this kind
of
thing but let me back up and I'll uh
show you the whole process from the very
beginning so I've gone around with a
sharpie and marked couple little black
dots on either side of the track there
right up next to the
rails uh where I want to drop feeders
down and like I said I want to do that
for every section of rail on the
layout and you know it is a little bit
Overkill it's kind of building in a
redundancy so if um any of the other
connections fail um you know there'll be
a backup for it so you won't lose
current to the rails it's just a good
practice now I've got a 1/16th of an
inch drill bit in my drill and I'm going
to go through and drill down through the
road bed right up as close to the rail
as I feel is safe without actually
touching
it I want a couple of pieces of
wire about uh you know 9 10 Ines long
like to give myself plenty of slack to
work with then I want to strip off about
um you know 3 to half an inch of the
insulation just from one end of the wire
feed that down through the hole and
here's the trick when you get it down in
here when you've got you know maybe inch
and a half two inches just left sticking
out you want to bend it back like this
bend it back on itself and take that
exposed bit of wire and bend it over
into an L
shape and then pull down from underneath
and the natural bringing action of the
wire is going to hold that in place for
you right there in the rail
webbing and that should hold the wire in
place long
enough get some solder on
there and then you can just pull the
wires down
all that uh wiring is hidden down below
the layout deck okay that's all the
sections on this side and I'll flip the
whole layout around and do the other
side
[Music]
[Applause]
[Music]
[Applause]
[Music]
[Applause]
now we can flip the whole thing upside
down again and solder the other ends of
those Feer wires to the DCC bus that we
installed back at the
beginning so there's nothing really
tricky
here don't have any reversing sections
or anything any weirdness like that so I
just need to come in and
remove a little bit of the insulation
here and
there and then connect the red wire to
the red
wire and the black wire to the black
wire I just like to twist it around like
so
there are clever little connectors you
can get for doing this they're called
suitcase
connectors in this case you'd need some
that would
connect 14 gauge to 28 gauge wire
couldn't find any of those available
locally so doing it here the
oldfashioned way little solder little
electrical
tape works just great okay now I just
need to do that on every one of these
connections about the only way you could
possibly mess this up would be you know
by accidentally connecting the black to
the red or the red to the black causing
a short circuit that's pretty
unlikely even if you're color blind I'm
just finishing up the uh the
final pair of connections
here and these are feeders coming off of
the turnout
but I've also got an extra
pair of uh feeder wires that I soldered
on
there and those are going to help me
power that frog on that turnout now
there are a few different ways that you
can power frog on a turnout like this
one um you could use a a switch machine
like the ones available from tortoise
you could use uh Taman Valley Depot frog
juicers those work great I use them on
the Thunder mes layout and on the
Goldfield and Calico but for this
project uh I think we're going to go old
school I want to do it the same way that
Vern Niner did it on the original austa
and Sonora Grande and that is with a
single pole double throw switch like
this one you remember that green
wire that uh we
soldered to the underside of the turnout
frog well that's going to go to this
Center terminal on the switch and then
the other
terminals get the wires coming from the
DCC bus for the inside and outside rail
respectively just like
that and this is going to allow us to
switch the
polarity of the
Frog depending on which way the uh
turnout is thrown I'm not sure
exactly how I'm going to configure
the controls on this haven't quite
figured that out yet so I'm going to uh
temporarily affix this uh to the bench
work with uh some 3M sticky tape and
this will allow me to you know test
everything
out make sure everything's
functioning the way I want it
to before I install it permanently
to actuate the throw bar on the switch
I'm going to use a good old tried and
true Caboose Industries ground throw
this is an HO scale one uh I used these
on the Thunder Mesa layout and these
were the same kind of ground throws that
Vern used on the estan or Grande so
should work fine here first thing I need
to do is
extend these
ties coming out from the throw bar so
I'll have a place to mount that ground
throw for that I've cut a pair of OC
scale 6 by8 to length and then when the
track is uh painted and ballasted that
should uh that should blend right in I
want to make sure this ground throw is
mounted about oh about one and 1/8 inch
minimum uh from this outside stock rail
so even the widest piece of equipment
will be able to go through here and have
clearance now I need to make a
linkage go between the uh throw bar and
the ground throw I've got some music
wire for that I'm sorry I don't know the
actual size of this music
wire comes out of my Scrap Box the the
actual size is not that
important long as it's you know stiff
enough and and fits and works so I want
to put a bend in this end gab boost
ground throws usually come with little
pegs on you probably have to cut those
off and drill a
hole for the other end of the wire which
is what I've done here you want to make
sure that the points are centered on the
turnout on the ground throw end I like
to bend this into a little U shape a
little hook hook in there again making
sure the points are centered and the
handle on the ground throw is straight
up and
down goes down in there now the ground
throw can be
mounted make sure we're
centered onto these extended
ties a couple of rail spikes or track
nails
now to power the layout I'm going to be
using an nce power cab those are super
easy to set up first thing I need to
do is attach the um DCC bus to this
little
plug which goes into this face plate
which will eventually be mounted
wherever I want the controls to be for
now I'm going to leave it let it
kind of float
free all right and then
that plugs in right there where it says
track hard to miss and the cable to the
cab goes in right
there and then the other end of course
plugs into the power cab
itself and then the power
supply plugs in right there again these
are all marked so that's pretty easy to
follow okay Moment of Truth we're ready
to plug this into
power and uh if there's a problem we'll
know right away I should get a red
indicator light
there yep that's good everything looks
good
here yeah this has a built-in circuit
breaker so if there was any short
circuits if i' wired anything up you
know backwards or wrong uh this would
shut down right away and then I'd have
to go troubleshoot the problem but looks
like we're in good shape to test
everything out just cleaning the track
here real quick with some uh odorless
mineral spirits well I've jumped ahead a
little bit and started in on a base of
the scenery for the Ayo which is going
to be over here there's going to be a
Trestle across it uh and that's because
you know I didn't want a big hole in the
scenery here when I'm testing out
equipment in case God forbid there's a
derailment and it goes you know
plummeting down to the the concrete
floor that would be a bad day so I
wanted wanted to fill in this hole and
I've got a couple of blocks of uh foam
just holding up the track here this is
some 1-inch thick poly stying foam which
I'm going to be using for the the
scenery all over the layout I've done a
little bit of rock carving here and
don't worry I'm going to go into great
detail on How I build all of the scenery
for this in a future installment right
now we've got estraya and sonor Grande
number three on the rails here it's a
040 Porter very short wheel-based
locomotive
so if there's any problems we'll find
[Music]
them oh no problems going through the
turnout that's good
bring her around to a stop here and
we'll do some more testing with that
turnout out so I want to take the toggle
switch and put it in the center position
that uh kills any current to the Frog
just a good practice flip the points on
the turnout for the diverging route and
then flip the switch over to uh Power
the frog with the correct polarity for
the diverging route
[Music]
now we switch things back to the main
line off around the track we can go
[Music]
one final little step I like to
do is to
take those ties that cut off lay
track and I trim off the cast in Spikes
all
that put a little glue on the bottom and
slide them underneath those those rail
joints for a more finished look
[Music]
and with that I think it's safe to say
that the track laying and track wiring
for the San Lorenzo mini layout are done
now I can move on to the scenery and I
hope you'll come back and join me for
that future installment coming up real
soon until then you can also follow
Thunder Mesa over on Instagram at
thunder. Mesa and I hope you'll check
out the resources available on the
Thunder Mesa Studio website at Thunder
mesa. Studio I want to thank you all for
watching and following along throughout
the year and a very special thank you to
all of our patreon members who help to
make these videos possible until next
time keep moving forward my friends OS
for now
[Music]
[Music]
