Building A Custom Osage Long Bow

Unraveling the Ancient Longbow
4 followers
3 Video Views·Aug 12, 2026
AI Generated·May contain errors
Video Summary
AI GeneratedThe video documents the process of crafting a custom longbow from Osage orange wood for a selfless humanitarian named Zadock. The creator details the technical challenges of working with this rare, high-quality wood—specifically the need to chase growth rings—and shares the inspiring story of the recipient's dedication to helping people in remote areas.
This wood has many names. Osage orange, hedge, horse apple, bowdark, which means bow wood.
It's one of the best bow making woods on the planet and for me here in Alaska it's a pretty
rare treat that I ever get to mess with one. I'm not building a bow for myself. I'm building a bow
for one of the most incredible people I've ever met. I'll tell you about him later. The first
thing I'm going to do is just make the back of this bow smooth so that I can draw on my design.
In Bowyer's Bible volume one there's an entire chapter about how to build a bow out of Osage
orange and one of the tips that I got out of that chapter is that I didn't pick up before
is to actually use a dull draw knife as you're removing the wood off the back of the bow.
The reason you do this is because a really sharp one has a tendency to dig and damage the layers
that you actually want to preserve. So I've got this big dull draw knife. It's not very sharp at
all. You can run your fingers right across it. I'm just removing some of the bark and a little
bit of the sapwood and so that I can get the design of my bow drawn out and once I get the
bow to shape then I will actually have to chase a growth ring. So Zadak is really tall and I'm
going to make this bow one of the biggest bows that I've ever made. I'm actually going to make
it 72 inches long because this is going to be a very simple flat bow design modeled off of the
in volume one of Traditional Bowyer's Bible. This knot here I'm going to leave extra wide
because knots are weaker pieces of wood that need to be protected by leaving them extra thick and
also not bending them quite as much. I'm just trying to make the entire thing roughly two
inches wide and then towards the tips it's going to taper a little bit and it's almost tapering
out of necessity right now because the center line gets close to the edge. So I'm just trying
to match that distance on the opposite side. Now that I've got the rough design laid out on my bow
I'm just going to thin it with this much sharper draw knife.
Okay now I've got this bow roughed out. It's about two inches wide. I have my ends and center
attached on a straight edge but it snakes around as it gets there. The next thing that I need to
do is actually take the bark and the sapwood off of the back of this bow. Heartwood bows are unique
in that the heartwood of these specific species of wood like black locust and osage is the only
piece of the wood that you can actually use to make a bow. The sapwood is very brittle
and so you have to remove it but when you remove it you actually have to get a consistent growth
ring across the back of the bow because if you're cutting growth rings it's like cutting layers on
onion and they want to separate. And this is where that dull draw knife really comes in handy.
If you use a dull knife the sapwood is actually more brittle than the heartwood and so the dull
draw knife sloughs off the sapwood but once it hits the hard heartwood it stops. As I get closer
you can see the yellow start to poke through. So this is the sapwood and then it gets dark right
before it becomes the yellow heartwood. We're after the yellow heartwood but we can't damage
any of that. So the closer I get the finer the tool. This is a shinto rasp. I'm using the fine side
and removing some material with this until I start seeing that dark color.
Then once I get to the majority of this dark stuff I'm actually taking sandpaper
and using my finger to conform to the shape of the wood. I'm sanding off all of the dark
stuff and getting to the orange heartwood. This is a very tedious process and it's make or break.
If I ruin this stage in the process the bow will explode when I draw it back.
So I was being really careful just removing the sapwood and taking my time with the sandpaper and
it was just taking forever and I was thinking man there's got to be a better way. So I went back and
read that chapter again and watched a Waylon Olive video and it seems like everybody drops down five
or six rings. So I took this little scrap piece of wood that I cut off the end and I tried that
and it's actually way easier to remove five or six growth rings than it is to try and make the
first one work for you. And I think it's because the glue in between the layers on Osage is
particularly weak. So if you're using a draw knife and just going really slow you can almost get it
in between growth layers and it just kind of flakes off on its own. See this here? It's almost
white where the early wood is and then the late wood's really dark. So I'm just bringing this
all the wood down to the same level. So this knot is giving me a little bit of trouble.
So you can see I've got the entire bow down to this growth ring and I've got one step up two
steps up and then right around this knot it's like difficult to see what happens but I've got
it chased down to this growth ring all the way up to the top of the knot. But then on the sides
it's one two three thicker. One two three. So I've just got to really carefully
remove from the sides of this knot which is a very difficult spot to reach.
So I'm doing it almost entirely with sandpaper. All right I finally got it chased down to a
growth ring but now I'm realizing how snaky this piece of wood is. I'll have to figure that out
later how to make a string go from end to end without having the bow on a twist out of the
string. But for now I'm going to thin it down. Now I'm just going to take this little saw
and cut down to that line in a bunch of different places and then I'll take a hammer and chisel
and knock those chunks off. Now I'm just going to use my draw knife and continue bringing this down
to the line. I didn't want to use the chisel and cut too far so I'm just going to finish it off
with a little bit more careful of a tool. This is a funky looking bow. That's one of the things about
Osage is sure is full character. It's going to look very unique. I'm going to narrow down the limbs a
bit more and just continue chasing a shape and I'm really just eyeballing this because the grain
on Osage is so unstraight that you can't really have like formulaic patterns like you can follow
on a board though. So I'm just following the grain the best I can and eyeballing a nice bow shape
making sure that both of my tips and the center of the handle are in line with each other. It's
okay that the center of the limb snakes out a little bit as long as the ends in the middle
are in a line with each other. The last thing I did before I went to bed last night was glue on
these two pieces of caribou antler and those will be my tip overlays to protect the bow from the
string. Now I just need to narrow these down and make them look a little bit more aesthetically
pleasing and put a string groove in there so I can start tillering. But the bow is bendy. Let me see
if I can show you. I just need to get that bend a little bit smoother so I'm going to put it in a
tillering setup which is just two hooks one with a pulley and a rope on the bottom and then the
other one holds the bow. And I'm going to pull with my desired draw weight and make sure that
the bow is bending properly and keep removing wood until I get back to the draw length. And since
the person I'm giving this bow to is so tall this is going to be a 31 inch draw bow. So I want to
tell you a story about the person that I'm building this bow for. I work for a sled dog tour company in
the winter time. One of the people that came out to do my sled dog tour was this guy named Zadock
Johnson and I always talk to the people that I'm taking on tours and try and get to know them.
And Zadock kept talking about how they practice jungle medicine. I was like what is jungle
medicine? And basically what he likes to do is he likes to go to some of the most remote places in
the world where people are suffering and he likes to help them. And on his most recent trip to Alaska
I met up with him and he was just super skinny. I was like whoa dude what happened to you? And what
he told me is that he was in the jungle helping these people escape from a tyrannical government
and he was only supposed to be there for a limited amount of time because he had a very temporary
visa and if he stayed too long he might not be allowed to come back. But he also realized that the
amount of money that he had spent on the plane ticket to leave this area was enough money to pay
for food for the people that he was helping and they were literally starving to death in front of
it. So instead of going on his flight back home he sold his ticket spent it all on food and then
stayed there with them himself only eating one pack of ramen noodles a day so that he could
continue helping people and he fed them for as long as he could. And then eventually it came time
where he legally had to leave and so he came back to Alaska and when he was on his travels he met
a couple other bowyers and they were making bows and he remembered that that's what I like to do.
And so he thought of me and brought me this piece of wood that he knew would be incredibly difficult
for me to get. He's just so thoughtful such an incredible person. So obviously the bow that I
make out of this piece of wood has to go to him. 45 pounds at 31 inches. That's a long draw length.
Okay moment of truth. This is the first shot through this bow. I like that quite a bit.
Gotta turn my head around so I don't hit the brim but this is smooth. I like it. So all that's left
now is to decorate it. It's already super functional. I like the way it shoots. Everything
is completely functional and now we just have to make this a piece of art. One thing that's
kind of unique about Osage is that it actually gets a tan just like people do in the sunshine
and the longer it sits out in the sun the richer the color is actually going to get.
I'm also going to wood burn a little bit on the handle. I'll put some links for silencers on the
string to reduce the noise that happens from the buzzing of the string as you release the arrow.
And then I need to call Zadak and see if I can get a hold of him. One of the unique things about
talking to Zadak is I don't know how to reach him. He's not frequently in America let alone Alaska
and I also don't know if he's going to have service where he is so I'll probably call his
phone and leave a message and then also message him on Facebook. But it might be months before I
hear back from him so I'm not going to wait around to post this video until I hear from him.
I'm just going to reach out and I'll see him when I see him.
