Big Build Off Competition week 4 - Creating the Walnut & Epoxy Table Top

Hertoolbelt
34 followers
4 Video Views·Jun 12, 2020
It is week 4 of the Big Build Off competition. A new virtual maker competition hosted by the original ‘The Builders Challenge’. 5 makers are competing against each other, putting their creativity and skills to the test building a TABLE.
The best part is that these tables will be donated to charities or families in need.
Follow along in this fun 6 video series, to see who will be crowned the Big Build Off Champ!
Thanks to this week’s sponsor MAS Epoxies for the epoxies used for this table top.
Welcome to Her Tool Belt and thanks for watching. I can't believe we're at week four of the big
build-off competition and I have put off this tabletop for as long as I can possibly wait.
A few years ago I was walking around New York City with some friends and we went to this
eclectic furniture shop where they had this entire corner of wood encased in epoxy furniture.
These pieces of furniture were so unique and it was really inspiring to see what they did
with the wood and the epoxy and I've wanted to try something along that line ever since.
When planning out this table I wanted to give a real wow factor to the tabletop. I thought it'd
be really neat to do a patterned wood top that's encased in epoxy that you could see through and
with Mass Epoxy being the sponsor this week there was no better time to try this unique furniture
technique. But then I've been waffling to myself these last three weeks,
oh this is a charity table what if the family hates it? What if I completely mess up because
I'm not an expert at epoxy? And what if it just looks dumb? But I finally decided to buck up
and just try it. But I do have the backup plan in the corner of the garage. So wish me luck this
week and hopefully everything turns out. The center of the tabletop will be a walnut herringbone
pattern encased in the clear epoxy. To accent the dark walnut brown I'm going to add some blonde
maple highlights. The maple highlights will go on the herringbone and embedded into the side
of the tabletop. I'm using the pin nailer to hold the maple in place. You won't be able to see the
pins once assembled. Once the piece is dried I ram them through the planer. Then use the crosscut
sled to trim them flush. I use the Dremel with a wire brush to remove any bark or dirt in the open
cracks. To avoid bubbles in the epoxy I'm using penetrating epoxy in all the cracks and the
crevices to seal them from producing air bubbles. While the herringbone piece is dry it's time to
build a form for the epoxy pour. I have an old piece of half inch melamine that I wanted to use
up for this. The form is a little over 60 inches long and 24 inches wide. Then I put two inch sides
on it. I didn't know if the epoxy would stick to the melamine so I lined the form with Tyvek tape.
I carefully placed the Tyvek tape in the corners first before applying to the bottom. I left some
quarter inch gaps in the tape because I'm going to attempt to super glue the herringbone pieces down
avoiding clamps on every piece of wood. I cut little quarter inch scrap wood spacers to space
out the wood. I put a few dots of super glue on the exposed melamine and pressed the wood down.
I'll be using Moss deep pour epoxy. It is a three-to-one mix then I slowly mix it with a
paddle bit and drill. The epoxy gets poured into the gaps and cracks. Then I use a squeegee to
spread it around. I like the deep pour epoxy it's thin and easy to move around. A heat gun is used
to pop any bubbles. While the epoxy cured I think some of the epoxy soaked into the wood and some
seeped under the herringbone wood so the grout lines ended up just below the top surface of the wood.
Time to pry off the form. The super glue method worked pretty good.
There were three boards I thought might be floating so I clamped them down during the cure.
I trimmed the excess epoxy and created a straight edge with the table saw.
Then used epoxy to bond the center herringbone to the side walnut pieces.
The end clamps are just to get an even height to support the boards.
Once cured I mounted the Rockler circle jig base to the underside of the table. The jig
is for up to a 52 inch diameter so I made a little extender to get it to 60 inches.
Then used a straight bit I went about 3 16th of an inch deep with each pass.
To make the tabletop look chunky I'm adding a second layer of wood around the underside of
the table. I used epoxy to bond wherever there was epoxy otherwise I just used wood glue.
All hand clamps were on deck for this effort.
I mounted the circle jig base up on a 3 quarter inch spacer
and trimmed the new boards into a circle.
Now to cut the groove for the maple highlights.
I used a rabbet bit then measured the height and depth. The depth is just under 3 8th of an inch
so I'll cut 1 8th inch thick strips of maple to fill the groove.
The 8th inch will allow me to easily bend and follow the curve of the table.
On the first and second rows I used wood glue and pin nails to hold the maple in place.
For the third row I used wood glue and all the clamps
again and I probably could have used about 10 more.
Then we're back to the router and trim bits to make everything flush.
The top of my center section is lower than the top of my wood sides
because the center boards were playing more so I need to fill it with more epoxy.
I ran a perimeter of tape around the tabletop
and covered the table with mass tabletop epoxy.
The tabletop epoxy is a 1 to 1 and quite a bit thicker than the deep pour
but it seemed to cure faster than the deep pour too.
Once it dried I added a nice chamfered edge and another coat of epoxy.
It's looking pretty sweet. What do you think?
Thanks again for watching and please subscribe
and you can check out more of the big build off videos in this playlist.
See you next time for the final reveal.
