Is This the Easiest Way To Automate A CNC Lathe?

Machine & Design
2 followers
1 Video View·Nov 11, 2026
Automation sounds great until you start looking at the price of robots, bar feeders, and other equipment. But does it really have to be that complicated?
In this episode of American Made, Justin Webb from Zealous Manufacturing takes a more practical approach to automation. Using a simple bar puller on the To
AI Generated·May contain errors
Video Summary
AI GeneratedJustin Webb from Zealous Manufacturing demonstrates how small shops can implement simple, affordable automation using a bar puller on the Tormach 15LX. He argues that automation isn't just for large companies with expensive robots, but is any system that increases machine runtime while reducing human interaction.
We are going to discuss automation and the 15LX from Tormach,
we are going to bar pull a job.
So bar pulling, very simple automation.
Doesn't cost a lot of money and every cycle starts.
We get that full bars run. You'll have
a small remnant afterwards, but we get a full bars worth of parts.
We don't have to sit there
every part. Hey folks, Justin Webb from Zealous Manufacturing.
We recently just came off of IMTS
and one of the big key topics was automation and AI.
We are going to discuss automation because one of the things
I think people overlook a lot is how to do automation simple.
If you see a lot of these big trade shows
and you see all these fancy equipment, you're
going to see hundred thousand dollar robots.
You're going to see pallet changing and machines,
pallet pulling machines, AI integrated into
all that.
And it almost feels like for some of the small shops,
like Dallas Manufacturing and some of
you other small shops,
talk to a lot of you guys at the show and automation kind of seems
out of reach, right?
You're not going to be competitive,
they say, because you don't have automation.
But one of the things I want to do is I want
to break automation down to a simplified idea.
So what I define automation
as is anything where you can get more runtime with less operator or
less human
interaction.
How are we
going to
automate
the 15LX
we're going
to bar pull?
So you can't easily integrate a feeder or a bar feeder on this,
that would be more of your,
it's pushing a bar in, you can magazine feed or stack up bars.
These pieces of equipment
aren't as easily integrated with that.
And to be honest, a lot of the feeders out there cost
more than this machine costs.
So again, I don't want to say it's out of reach,
But you can do simple automation.
We're going to use a bar feed.
So.
Bar puller just has two rollers here.
You can see upper and lower and these are spring loaded. So
if my finger has a piece of material
You would move in
These would go over they grab the bar you open the collet
and you pull out your material to their desired length
And then you pull that so we are going to integrate
that into this process and we are going to hopefully
We're going to run a two foot bar on this
plastic job and we are going
to see how many pieces we can get out of the bar and every cycle
start we get that full bars run you'll have a small remnant afterwards
but we get a full bars
worth of parts we don't have to sit there every part
so let's hop over to the machine and show
you
guys
that so
when
bar
pulling
rigidity
or
stiffness
in the
material
can
matter
so
you'll
see here in a second when this bar puller comes
in the material deflects down because it's not rigid
As we pull back,
And once we ultimately let that material come back out
of the rollers, you'll see it
deflects back up. So concentricity could become an issue
when you have that happen.
So you
guys saw
it run in
plastic.
Now let's
jump over
and show
you guys
a job
we just recently ran in steel.
So let's jump over and show that steel part running.
One thing I want to highlight,
you'll see it in the OP2 threading cycle,
is we also use the pneumatic collet closer,
which you have to have the bar pull.
That's what is physically telling the collet to open
so the bar pull can pull.
Otherwise, it's not going to go very well.
One thing I want to kind of highlight here is while
the pneumatic collar closer isn't automation,
it makes things a lot simpler.
So tying back to that less involvement theory of automation,
I think pneumatic collet closer is a great option, right?
I put a collet stop in a 5C collet.
i could load every part hit start z zero was already set
so it was just i could literally
just put them in as fast as they could finish
if i didn't have that right i'm physically going
setting z tightening it right if you can think
of a three jaw instead of a pneumatic collet closer
or you know you're going in there you're tightening
the collet with a collet wrench
i didn't have to do any of that so while it's
not a traditional form of automation
i think it really helps to speed some things up again tying back
the theory of less involvement
So automation. It's not out of reach
or grasp for a lot of us small shops.
I've shown you a very simplified way of automation.
There are a lot of other ways
you can automate. I've seen people run four-sided
or eight-sided kind of tombstones on a fourth
axis on a mill. They just support
the other side make a little trunnion. There's a lot
of ways you can get unattended run
or less operator interface while running parts. So
I don't want anyone to be intimidated by the word automation.
I know when people think automation
they think these giant systems or these very expensive systems.
Automation and I actually just
recently talked to someone that they're looking at a big machine
because they want to run three
Three or four Op1 and Op2s,
they got to stack a whole bunch of vices on there, and I said,
The price of that machine,
if you could get a smaller machine with a robot or cobot or
whatever it may be, and you could just op one,
op two in that system, you don't need
the big machine.
You save the money on the expensive.
Now, again, I'm talking about a cobot or a more expensive option,
but automation is going
to make us all a little bit more efficient.
We're going to hopefully have better
margins once you pay off that system.
You have to look at your ROI there, obviously.
But I think it's not without,
it's not out of reach for a lot of us, even us small shops.
So you've heard us talk about it a lot
at our panel discussions at IMTS, but I think this is
going to be the way a lot of us small shops can gain efficiency.
We can do other things and use
some of those extra funds to reinvest in equipment or to simply,
you know, give ourselves a little
A little cushion in hard times.
So.
I hope this was helpful for you all.
I don't want us to be scared of that word automation.
And I want everyone to realize that automation is not far out of reach.
You can just have a palette on your machine.
And if you have quick change fixturing, it's kind of automation.
Pro, as you heard Luke from Crescent Machining say, simple automation.
You can check some of the features in the machine instead
of pulling it out, realizing you've got to readjust,
putting it back in, indicating, etc.
Even a pro toolsetter, there's simple forms of automation
that make your job a little easier, save you a little bit of time.
So I hope this was helpful for you all.
If you guys liked or you have any questions
on my opinions on automation,
again, I'm not an expert, drop a comment below.
We'll respond.
If you want any more information from any
of the other contributors here at Practical Machinist,
a lot of them check the comments as well.
So drop a comment below.
We'll be sure to reach out to you guys, help you out as much as we can.
As always, like, subscribe,
and turn on notifications for more Practical Machinist content.
