Don’t Do This Alone: Replacing Ball Screw Bearings on My CNC Machine)

Machine & Design
2 followers
10 Video Views·Mar 18, 2026
We're here with Brent. He's going to rip my machine apart.
I'm going to replace the X, Y, and Z bearing.
And we end up replacing two switches and fixing another switch.
So that little 90 degree head is pretty sweet.
I've never seen one of those, to be honest.
Oh, it's clean in there.
Look at that.
Doing sled pushes right now.
Yeah, five or six years ago.
And they would actually create divots in the cut.
It'll get rid of them on the ball bar.
So it's better to leave them at zero and let it have the friction.
This is the switch in question.
See how slow that moves out.
Hey guys, Sean here from SV Solo.
And today we're going to rip apart my machine.
Actually, I've already ripped apart the machine.
We've already done the work.
So I'm filming this after, so you'll see me in a different shirt.
But you've seen my ball bar video prior to this.
We diagnosed that we had some bearings go out.
And I'm going to replace the X, Y, and Z bearing.
And we end up replacing two switches and fixing another switch.
So a couple problems along the way.
But I hope you guys enjoy this video.
And let's go get dirty.
All right, guys, we're here with Brent.
He's going to rip my machine apart.
And nice to meet you, Brent.
Thanks for already digging in.
Yeah, yeah.
All right, so we have the bearings, end bearings.
We have the cartridges and a couple switches I want to replace.
Here's the other two bearings in here.
You said the Z is the worst.
It's the most difficult because it's suspended.
The ball screw looks good.
Yeah, yeah, not bad.
All right, cover's off.
Making progress.
Gotta clean the panels.
So I put them back up.
They're nice and shiny.
This jam nut pretty much holds everything together.
Once you loosen this bolt, then this whole thing pretty much spins off like a nut.
This is the coupler here.
These two things you just loosen.
And then the motor will just pull out of this guy.
Oh, OK.
So we're going to pull the motor out.
So yeah.
So the motor is going to come out.
These are the coupling for the motor.
This is what pinches the ball screw to the bearing and to the other end of it.
So it's going to block the head so it won't fall.
Yeah, if you don't have it blocked right too and you remove these bolts.
As soon as you take the bolts out, it would spin.
Oh, because the weight just holds it.
It'll just want to go down.
Oh, look at that.
I guess we'll need that later.
Yeah, I don't like to lose it.
That's for sure.
We'd have to make one real fast.
This tool is to lock this thing in place so I can break the top.
You notice as he's jacking, the ball screw is spinning.
So I got a little tool so I can lock it in place.
And then I'll use the mag vis to kind of hold it from moving while I go up top and crack it loose.
So I'll crack loose this guy, this nut right here.
Once I got it loose, then I'll tighten the jam nut so I can loosen up the bottom one.
You have to be extremely athletic to do this job.
This is a young man's sport.
No matter...
I wonder all the apps engineers that are older are like, I just can't do this anymore.
Yeah, this job is a...
It takes some time and some back and forth.
Once we loosen up the other one, the ball screw is completely loose.
Yeah, so we can screw it up and down, get the bearings out, screw it down,
get the bearing out of the top, replace it, screw it back up.
We'll put the nut back on top, take this guy out, replace it, and then...
Do you used to work in a machine shop?
I actually worked for the factory, the Haas factory, for 15 years.
Oh, did you?
Yeah, I did.
That's the bearing we're going to replace.
And now that we got that out, this thing can spin down.
So you just pulled out the bottom bearing.
That's the less...
Load, yeah.
Loaded.
It's just a port.
I'm going to back this thing.
Yeah, this ball screw feels good.
It's definitely your end bearings.
Nice.
Because if it was bad and we started to spin it, it would just start to go down.
It lost all its preload.
Oh, right.
OK, it's not very tight.
Yeah, exactly.
So if you have the preload in it, which means that this thing does,
that means it's going to be tight.
There's not going to be a lot of backlash in it.
I don't know if you can see from up top there.
We just backed it out.
Backed it out.
And then we're going to pull that bearing out of the top of it and then replace it.
The universal tool, the hammer.
I've got a little plastic now that helps me get stuff out.
That's tight.
That's good.
Yeah, there it is.
That's the old SAL 1.
And that spacer that we have will make up the difference between the new SAL 1.
Yeah.
Rubbing my finger in here.
I can feel it.
You can?
Yeah, a little bit.
Yeah.
Oh, yeah, for sure.
This is definitely bad.
These are the things that fail and not the ball screw.
Yeah, which is good.
I'm pretty stoked.
It's going to be nice to hear this thing real nice.
I mean, if I'm going to dig into this thing, I've got to do all.
I'm just going to do them all.
I mean, it's 22 years old.
Why not?
Yeah, exactly.
Especially the ball screws are decent.
Yeah.
So these things have shims in them from the factory.
So we'll put these back in when we put this guy in.
So what happens is at the factory, they set these ball screws up and they'll run an indicator
along the top of the ball screw.
So they'll put an indicator on the guide rail and then they'll indicate the ball screw all
the way through.
And if it has any kind of up and down motion, they'll shim it to make it dead nuts.
So it's flat.
So the ball screw is running perfectly.
No winding.
So yeah, the shim would go.
Is it going?
Yeah, it's going here.
And so it's shimming it towards us, but basically giving it a little bit more height.
This one's probably almost.
Yeah.
I have a tool that I put on here now.
I'll put it in place.
Tap it in.
Exactly.
I'll typically use one of these plastic pieces.
So I hit the outer race because you don't want to hit the inner race.
You want to keep it on the outer rail.
Sometimes it doesn't.
Sometimes it catches the edge when you're doing it.
So I'll use an older bearing to stick it on there and then make sure that it's sitting
all the way flat against it.
All right.
Inventory check.
We have this piece.
He said we don't use the black one.
He's never had to use that one in this type of models and machines.
Already had the bearing in.
It's the spacer and the shims.
This plastic will be hammered in from the bottom side until it sits flush against it.
So this won't go into the casting.
This one will go up.
And then this one will just sit on the ball screw.
And when you screw it up, it'll kind of, yeah, mesh in place.
You got to be extra careful with these machines.
Yeah, because anything can drop in there.
Yeah.
Chips everywhere.
You want to be doing this by hand too because you want to make sure it goes.
Freely?
Yeah.
It goes in there smoothly and doesn't get caught in anything on the way.
Pretty close.
So I'll get all four of these bolts in there.
And slip the shims in the back?
The shims and then the pins.
All right.
Pins.
Don't forget the pins.
We have the shims.
Sometimes you can, the shim will be in the way of the pin.
Pins are in.
Yep.
So now the jam nut up top here, is that what you're doing?
Yeah.
The jam nut is sucking the whole ball screw up.
So I got to make sure that I'm not sucking up and the nut on the other side is not pulling
the bearing with it.
So I'm going to loosen that.
Loosen that nut up a little bit more because it feels like it's starting to pull it.
Gotcha.
Just got to be careful when you're doing these.
Just be really attentive to what you're doing.
Can't be any more careful than hiring someone else to do it.
So the top is done then?
Yeah, the top is torqued.
And now I just got to rotate it around so I can tighten the pinch nut.
And basically you just rotate this thing around until I can see the pinch nut.
So as he jacks his head up, you can see that it's moving the ball screw.
And that's how he's orienting the clamp bolt.
Yeah, you get to it.
Pinch bolt.
So what did you say this one was torqued to?
Uh, seven.
Seven, so pretty light.
So see how that's off right there?
Yep.
I want to basically rotate it around the ball screw until it lines up.
Because this one, it's got a break on it.
The other ones don't.
You can just kind of pop them in there.
So he's going to jack this up just to rotate.
There it is.
All right, we got to clean this thing up.
It's going to be ready for it at some point.
Good enough.
Man, that sounds way better.
Yeah, I'm going to loosen up the nut housing and then kind of float it in.
It doesn't have any load on it, but I just want to make sure that
it's got the best alignment for longevity.
Just run it up and down and...
Run it up and down, kind of get it centered in place.
Once it's centered in place, then we'll torque it in.
See how nasty it is in here.
That's why I love these trays.
Oh, not too bad.
Yeah.
Wow.
Dude, that little 90 degree head is pretty sweet.
I've never seen one of those, to be honest.
Yeah.
Oh, it's clean in there.
Look at that.
Yeah, that's good.
Yeah, this axis you can move.
Okay.
Yeah.
This makes it way easier.
Yeah, exactly.
You can just move stuff around super easy.
How does it feel?
Good.
It feels really good.
So in order to do the Y-axis, he has to pull this bad boy off the lube tray.
Right now he's taking off the lube line because you can't get the thing to hang.
It's jammed in there, so I'm going to have to remove it from the lube panel side.
So now he's breaking loose the motor.
Yeah, pull this off and then I'll jump around and loosen up that coupler.
He's doing sled pushes right now.
Yeah.
This little tool here, just like doing the Z, doesn't allow it to spin.
There it is.
So there's that coupler spacer.
Yeah.
He's got the bearing coupler in there now.
New coupler is in.
All right, I guess we're ready to ball bar this thing.
Check it out.
He's got all three axes done.
It'll give you an accurate measurement.
There it is.
So these spikes right here are normal when you replace or add new ball screws.
They're called friction spikes.
So you'll get these and they'll kind of move away as the machine breaks in.
They'll kind of break in.
These friction compensation, you actually want these at zero.
Did a test, I don't know,
five or six years ago and they would actually create divots in the cut.
It'll get rid of them on the ball bar.
But what happens is when it comes around,
friction compensation is kind of the extra nudge when it's starting.
So it's better to leave them at zero and let it have the friction
because you're not going to have that digging in the edge of the cut.
So 138.
I always make sure they're at zero.
All right, so the ball bar is in.
Yep.
Looks pretty good.
All right, guys, we're back for day two.
Kind of ran into a few other issues.
We're going to replace two cables and maybe look at the actuator.
Is that what that's been called?
Yeah, so the tool release piston.
It's just a little slow to hit the unclamp button.
So I changed the switches in the turret,
but it didn't help my sticking because it would like go in and then stop the shuttle.
So he's going to check that out.
But usually that's caused by like maybe rust or...
Yeah, typically water in the lines.
Water in the lines.
That's what we're doing today.
And I have a new shirt.
Thanks, Devis.
And as for the new blue shirt, it matches my hat.
So right now he's taking the Y-switch off.
Pulling this guy out.
That is the Y-switch.
Yeah.
Where did it plug into?
Down here.
Oh, interesting.
OK.
It's got a little junction area.
OK.
Yeah, pretty simple.
So because I unplugged the switch, the machine recognized it.
So I have to do setting 53, dog without zero return.
Oh, so there's a brick in the cable right there.
A couple of them, yeah.
Oh, yeah.
There's a few of them.
Every once in a while, it won't hone properly.
So new cable's going in.
If you guys are going to do the X-cable, it's 10 feet.
And then the Y-cable is 6 feet.
Oh, it's like a rubber flashing.
It's plastic, so there's no movement in it.
You just got to get all the cables in there.
So he just put this plastic piece in there.
Just keeping these guys together because there's no channel on these guys.
On the newer style ones, they have like a track.
And these don't have a track, so.
So whenever you replace your cables, you got to reset the grid access so it bumps proper.
It's got to come off the motors a certain distance.
So it's not close to zero on the motor or else it'll trip out.
See how they both are at one?
They shouldn't be like that.
Should be opposites.
And eventually it turns to zero.
That's the issue.
Yeah, so this one right here is super, super slow.
This is the switch in question.
See how slow that moves out.
It's all sticky.
All right, I cleaned it up.
Threw some WD-40 in there.
And then I cleaned it out with IPA.
But it's super fast now.
Should be good.
When I seal these covers up, I use a...
He's like a black RTV.
Oh, black RTV.
Yeah.
I like to use the gasket maker.
This is the silicone based one.
Thanks, Brent.
I appreciate it.
Brent from Northwest CNC.
Extremely busy dude.
Only wants the good customer.
So I do appreciate it.
There's no way I could have done this by myself.
Yeah, yeah.
No problem.
All right, man.
It's a pleasure.
All right, she's ready to go.
All right.
Thank you.
All right.
We made it through another episode of How We Do It.
And that was kind of a doozy because there's no way I could have done that myself.
Thanks, Brent, for coming out.
Honestly, it probably would have took me three weeks to try and figure that out
and probably would have broke it anyway.
So yeah.
Hope you guys enjoyed it.
You know, now you know.
Don't work on your own stuff.
Just hire someone out to do it.
See you on the next one.
Later.
