The Final Operation On Our Massive Blisk

Machine & Design
2 followers
Nov 7, 2026
One wrong toolpath could ruin this massive blisk. Watch Barry tackle the final 5-axis CNC machining operation on the TRIMILL VS 1614, using Mastercam strategies to control chatter, finish thin blades and machine complex pockets without gouging the part.
…
AI Generated·May contain errors
After this we just got one tool path left.
I'm excited because this part
will finally be out of my life.
A four bedroom house, two Ferraris, and a thousand salads is
what I could have bought,
but I don't eat salads and I ain't gonna fit in no Ferrari. So instead
we got this machine right here.
All right, all right, maybe it didn't cost that much, but if
you've been following along with our series you know we've
been machining a big old Blisk.
Well today we're going to be starting our fourth
and final operation but before we get into some
sick machining let's go sit down to the computer
and I'm going to walk you guys through
how we process this part.
The very first tool path we're going to do is our blade tip finishing.
You can see the fillet here we got one, two, three,
four, five surfaces. For this tool path I'm only
going to use three axis motion
and what I've done is create a plane where I'm looking straight down
down at the blade.
The toolpath that I chose to do this was
Our multi-axis unified and we use the morph strategy.
You can see both of our morph lines
here. I use the top of the fillet
and the bottom of the fillet and then the surface
we're machining is the fillet itself.
So if we verify that tool path you see
our tapered ball end mill and we're
Around and around and around.
It's very important the order that we go in here. We're starting at
going to go just around the fillet.
the tip of the blade because right now the blade's at its strongest.
So we have 50 thou stock around
the whole blade and we're starting at the top of the blade
and we're going to work our way down.
So naturally the first tool path is going to be the fillet.
We take a look at our stock
model after that operation we can see
that the fillet around the top of our blades is done.
And now we're going to start the blade
itself. Now if we take a look at our
Swarf toolpath you'll see what I did
is take several step down passes that are
about between 100 and 150 thou deep.
And for each level that we machine we're
doing two passes. We're doing a semi-finish pass which takes us down to
10 thou stock and then we're doing the finish pass and
we're doing that at each depth.
Now this is critically important because
once we've gotten to the bottom of the blade
we can't just go in and do a finish pass
to take off that final 10 thou.
We have to do that at every level.
If we don't, what we're going to end up with is a ton of chatter.
Our blade's going to look terrible, and we don't want that.
So we're finishing it at every depth
that we cut for our semi-finished pass.
So if we verify this tool path,
you're going to see the tool coming down,
doing that semi-finished pass first,
and then it's immediately going to go into its finished pass.
Now, something to note about processing a blade like we are here
is that we're most likely going to see machining lines
for every depth that we cut with this tool.
Now under normal circumstances that's not going to be a big deal
because most of the time parts
like this are going to be electro polished after the fact.
But since we're doing this for camera,
I want these blades to look really good when we're done
and I'll show you how we're going to do that
next.
All right for our next trick to get
a beautiful blade we're going to come in and do another
swarf pass except this time instead of doing it
in shallow little depths we're going to do it in two
passes. So if we take a look
at the tool path you'll see we're doing full five axis swarf milling
and we're taking the blade in two depths.
Now again these are just spring passes so it's going
to remove absolute minimum amount of material
so I'm not too worried about getting chatter
but what it is going to do is remove all
those machining lines from our previous operation.
All right, so our blade finishing is now complete,
so let's go take a look at the part.
So our finish looks really good,
really consistent all the way down the blade,
and these things are super thin. You hear that?
Oh, my nail. You get that ring because the blade
is so thin, so if we take a look at the thickness of the blade.
All right, so that's how thick our
blade is up at the tip. It's a little over two and a half millimeters,
and the blade itself is...
just under three inches long
so that's an awful thin blade for that height you know you may think
to yourself that you're not going to be doing any blisks anytime soon
but these same strategies can
apply to any thin walled tall part that you have
so keep these methods in mind next time you've got
tall thin walls to worry about.
All right so for our fillet finishing we're not doing anything
fancy we're just taking our tapered ball end mill
and working our way around the fillet at the base
base of the blade. Now we're going
to get quite a bit of five axis motion so
It should look pretty cool but after you watch it 32 times I'm
sure it will be a whole lot less cool so let's make some chips.
Oops.
What's really critical
is that we make sure
as we're coming around the blade
we don't let the tapered flute of our tool touch the blade itself
so we have a little bit of side
tilt and a little bit of lead angle
on our tool to make sure that we're not
cutting with the center of the ball
and that we're not gouging our finished blades.
I've had some coffee but that doesn't mean that I'm not still sleepy.
The difference is I can
take a two-hour nap at lunchtime. I can't do that here.
Titan frowns upon sleeping in the machines.
Although we do have some nice couches over
in the break area.
We have a pool table, a foosball table, ping pong. Game time!
Saltwater fish tank. Cold brew coffee on tap.
Sorry guys I'm not bragging I'm
just saying it's pretty sweet. Ah here's Dumb and Dumber now.
Oh yeah huh. I see you're a sweaty bear.
You must have lost a half foot.
That was pretty rude. That was pretty rude.
That's why it's all about working smarter not harder.
That's why those guys are going to go work harder right now.
All right, so we take a look at the part now.
We can see that the fillet is finished at the bottom
of our blade, but we still have some material left here in our floor.
So our very next toolpath is
going to be using the same tool to come
in and get all this material out between the blades.
Then after that, I'm going to rerun both
of these toolpaths with coolant so they look pretty.
So this toolpath, there really isn't that much to talk about.
All we're doing is finishing the
floor in between our blades.
Now the only challenging part of this is we got to make sure
That we don't get too close to our blade with our tool
and end up gouging our finished blade surface, so let's not do that.
Now a lot of the times on blisks
and impellers the floor in between the blades isn't that important,
but what you do want to do is you want to run
your tool parallel to the direction of the flow.
So that's what we're doing here,
making sure that our tool follows the direction of flow
because there are going to be some cusps down there in the floor.
The most important part on a blisk or an impeller
or a propeller is the blade geometry itself.
So that's what we focused on and we're
not going to waste a lot of time trying to get
a mirror finish out of our floor.
Today for lunch I had some substandard chili.
What made it substandard you ask?
It had beans in it.
In Texas we don't put chili in our beans.
It should consist of at least two different kinds of meat,
a whole lot of peppers, and
then the juice from the meats.
That's it.
It wasn't that.
It was terrible.
I wouldn't
feed it
to my cat.
Now you can see some of these things are starting to get nice
and shiny. We've got our faces faced
off with our three inch Dodeca.
We have our dish finished done, all of our blades are finished,
our fillets are finished,
and our floor between our blades are finished. Now the only thing that
we have left to do is going to be the walls of our pocket,
the fillet at the bottom of our pocket,
and the fillet at the top of our pocket.
All in all though this part is looking pretty beautiful,
just like me.
Alright, so right now we're just using
our half inch GoMill Pro ball end mill and we're
taking a semi-finish pass around the
fillet in the bottom of our pocket.
Sounds pretty good but I expected it to,
it's just a semi-finish pass so we're not doing
anything crazy.
I certainly hope I don't do anything crazy.
Right now we're almost over the finish line
but that's when most of us programmers and
machinists start getting the most anxious.
No, if I start dancing in front of the camera that's
when something crazy happens.
I know everyone wishes
that this was some more complex five-axis tool path but all we're doing
is a fillet and our pockets are in the vertical orientation
so that's how we're machining it.
Yes those are porcupines of doom. Little cactus needles.
Remember a long time ago I was in Arizona
and my uncle went up to a paddle cactus
and flicked the needles and they all flew off and so
I thought oh that's pretty cool I'm gonna try
that when he's not watching. Don't ever do that.
It hurt a lot, just like our camera guy
when he tries to get his cameras out of my machine.
You know, there used to be this redneck that worked here.
I'm not going to name any names, but he had a mullet sometimes.
First, I need to drink a cold beer.
Whew, mouth getting a little dry.
Good God.
He liked to talk about how all my parts had
this signature chatter pattern.
Oh, there's Barry's signature chatter pattern that he loves so much.
But I don't see that anywhere on this part.
You know, he could probably learn a lot if he came back here.
My name's Bo Nogo, machinist extraordinaire.
And I'm here to make parts. 30 years experience, 25 years old.
You know, when Jesse left here, I'm pretty sure he went on to
star in one of the next Hills Have Eyes movies.
That's true.
It's a shame we lost a mediocre machinist in this world.
You give me baby.
Maybe.
All right, so now the fillets in the floor
of our pockets are semi-finished.
We're going to come in with the same tool
and just do a finish pass on it so everything looks beautiful.
Here we go.
Now nothing fancy here, we just left five thou stock on those fillets.
We're tightening up our step over a little bit and that's it.
After that we're on to our pocket walls.
Blow some of them chips out of there.
Ah the benefits of through spindle air and coolant.
That keep my part nice and clean.
All right so we just finished machining
the fillets in the bottom of each of our pockets.
So let's go take a look at that.
Now if you look in here you can see the outline
of what our ball end mill just finished.
Now up next we're going to use our tapered ball end mill to
swarf mill the faces of the walls here.
Now these walls have taper so we're
going to be using our c-axis for rotation a lot
and our b-axis for some tilt.
Yeah, I don't want to see no more machining lines in my part.
You think I am, Jesse?
I could have finished these tapered walls just
by using the ball end mill and the vertical
orientation, but that wouldn't look near as cool.
Unfortunately, full synchronous five axis means
that this operation is a little bit
riskier, and we only got one more tool
path left after this, so wish me luck.
Now one of the nice things about swarf milling
is that we're not going to end up with a bunch of
steps or lines in our wall.
It's going to be a nice consistent finish just like we have on our
blades. Quit putting chips all over my beautiful part.
It's the only time I don't like seeing chips
of greatness when I want to see the shine
and the beautiful beautiful rainbows. That's why there's
so many songs about rainbows.
Why are there so many songs about rainbows?
Rainbows have nothing to hide.
Now a toolpath like this can look pretty complicated,
but all it is is a swarf toolpath.
The CAM software figures out what all the rotations
need to be on our B and C axis.
So really, it's nothing different than programming,
say, a three-axis contour toolpath,
except we're giving it a top curve at the top of our surface
and a bottom curve at the bottom of our surface.
Then our CAM software attaches the tool to both of those curves
and follows that surface around.
And it's doing a fine job of it.
Way to go, Mastercam.
After this, we just got one tool path left.
I'm excited because this part will finally be out of my life.
You know what?
I don't know about you guys, but my favorite part
of the last video was the way that our editor
shoved Titan in there screaming after I said
that he destroyed all the inserts on the tool.
And he used the actual clip.
From when all those inserts got destroyed.
That's how I keep my stress levels up!
AHHHH!
When you're the CEO of a company,
you can afford to be a little bit braver
with the things that you're doing on your machines.
Oh, here goes Shop Cop,
probably making sure everybody who's actually working
has their safety glasses on.
Two of the worst things in this world,
a lathe guy and an inspector.
Just kidding, I love Travis.
Just like that, we're down to our very last toolpath.
The next thing we got to do is just put
the fillet around the top of each of our pockets
and this is just going to be a three-axis tool path
so it's nothing fancy but it's got to be
done. All right so you can see we got
a nice finish now all those steps are gone that used
to be in there. The only thing that's left for us
to do on this part now is to add a fillet to
the top of each pocket. We're going to do that using
that half inch ball end mill right there
and after that this part is ready to rumble. Let's go make some chips.
So now we're all done running a few
of our features with coolant and check this
part out. All of our flat faces are stunning,
they have rainbows coming off
of them, our pockets are done, pocket floors,
pocket walls, all of our fillets
and of course our blades.
Now running this thing over here on our TreeMill VS
1614 was a great idea because this thing came out absolutely beautiful.
Now, the only thing that I haven't done
so far is finish roughing out the pockets on the back
of the part, but we've already done all
these pockets on this side of the part, so there's
really no point in me showing you guys that.
So as far as you're concerned, this part is finished.
Now, if you guys want to see me run another one
of these parts live and in person,
register for Boombastic this year.
Tickets are 40% off right now on our website at
titansofcnc.com, and I'll see you guys here. Please like and subscribe,
and I'll see you guys again in our next video.
