Well, I had so many different ideas for these two cabinets, but things didn't pan out quite the way I'd envisioned.. So I tried to make the best of it and changed up the plan!
I couldn't be happier with the end result, although I do still daydream about the different things I could have done with these two apothecary style cabinets. Matching night tables... two separate hall tables... so many possibilities. But I ended up combining the two into one long cabinet with a new pine top and base, and added industrial style wheels and some antiquing & distressing techniques to make it all look older than it is.
Hello everybody, welcome to another video.
I purchased this set of side tables from Facebook
Marketplace. He was asking $180, asked if he would take $150,
which he accepted. It is a little bit
high for these, but it's so rare for me to come across two of them.
They're not in the best
condition, they are sturdy,
and they have a look that really appeals to me, but I have a lot of
work to do here. Finding two of these at the same time gave me
a lot of different options, and my
vision for these pieces changed quite a bit
as i went through the process of redoing them
so let's go on a journey my name is angie
and i refinish furniture sometimes i paint and sometimes
i don't but i always do what i can to save old pieces
from the trash welcome to my workroom
before i can do anything i need to get
these pieces clean there were these little rubber cord
guides stuck all over them i don't know what
this is it looks like a fried egg or a flat boob i'm
not sure these took quite a while to clean up
so as i'm showing you here what i was doing i'm going
to talk a little bit about what was going on in my head at the time
so i was initially thinking that
i would redo these as a set of oversized nightstands they're
a little bit taller than most
vintage nightstands you find and even
though these aren't literally vintage these were made i think
in 2014 with the apothecary style drawers it has
a bit of a vintage look the problem is they're not
quite as deep as a normal nightstand
and i wasn't sure if that would be practical as well as these
top three drawers which are all small i wasn't sure how well
that would work so then i thought
maybe this would be a great opportunity
to do two completely different looks i was thinking maybe of
doing one sort of farmhouse vintage
and doing the other one like super glam a beautiful deep color
and maybe like gold handles
and a little bit blingy if you will it's not really my style but
i thought this would be a cool thing
to do with these two pieces. i actually posted on my community
feed on my YouTube channel and asked for opinions
of what to do and it was quite split. it was about
half of the people saying keep them together
and the other half saying do something completely
different with them. but i came to the decision
of doing them separately but as you'll see shortly
that didn't really pan out. i
do believe that these pieces
were initially sold at a department
store like Target they have a partial wood frame
and the rest is MDF there is a very thin layer on
the top and sides as well as the front
of these trim pieces that is a cheap veneer or some sort
of textured laminate i think it's veneer
but i don't think it's anything that would be worth
saving so my best option for these would be to
paint them i am going to be reusing the hardware
i'm not quite sure yet what i'm going
to do with it they're very small little pulls and they match
the scale of these perfectly now I know
you're probably sitting here thinking oh
my gosh it's been three and a half minutes just of cleaning these two
pieces actually took me about an hour and a half to clean so that's the
extremely condensed version they are pretty gross
so for one of these pieces
my plan was to remove the legs
and this little bit of trim here and add wheels
so the wheels would sit down
on this lower trim area right here that was my
plan as I mentioned things didn't exactly go to plan so first I removed
all of the screws I had a feeling that this would
also be glued down but I
didn't expect it to be quite as bad as it
was I was able to pry part of it up
but I ended up breaking the lower section
which is a huge bummer there was
no way for me to separate these it just it
was too well put together it was
strangely enough. So now I am without a lower trim section.
So this obviously greatly changed
my plan for this piece, and that's the aftermath.
These were glued down, doweled down, and nailed
down. Not bad for such a cheap piece of furniture.
I cut off the dowels flush and removed all of the
brad nails, made a few repairs,
and this was what I was left with.
So at this point, I started to
think more about what I was going to do.
I knew I was going to replace the tops. I could have
sanded them down and painted them
but I decided that I was going to try to put these two pieces
together and make one cabinet out of it
and I'd be replacing the bottom and replacing the tops
and adding wheels. So I had
to deconstruct the base of the other one.
On this one this back piece
of trim was stuck to the bottom frame
so I had to remove that and then glue and tack that back on
to the back now the difficulty with removing
the tops is that well it's the same problem actually
i know it's going to be glued on and i don't want to break this trim
so i have to do this a bit
diligently start first by trying to get a putty knife in there
and then i can just hammer it off
thankfully the tops
were a lot easier
than the bottoms
for a few spots that
needed some repair
so i'm using some epoxy to do that wood glue
is not really going to work on mdf my apologies for
my head in the way there. I was able to pop
this back on and just clamp it while it dried.
Because the trim had been glued to most of the frame here,
I had to chisel off a little bit to
get it smooth and then grabbed my sander
and an 80 grit pad and smoothed it out even more.
If you're new to this channel, welcome!
Please consider hitting that subscribe button if you
like this sort of content.
And if you've been here before, welcome back! I appreciate each
and every one of you so here's where we're
at at this point i'm now measuring for my top and bottom
as much as i would have loved to put
a really nice piece of wood on the top yeah this isn't
happening i came home with some pine pine is fine even
though these two pieces will be attached at
the top and bottom i need to make sure
that they stay tightly together so i'm pre-drilling some
screw holes
in this middle section here
so that i can screw them
together i use my miter saw to
cut the boards for the bottom i could have done an entire flat bottom
but i don't think i will
need that this should be just fine
and i'm going to attach them together with some wood glue and
pocket screws this Kreg jig makes quick work of adding the pocket holes
and if you would like a
more in-depth view of this tool
which is awesome i will link to another video down below where i go
more into detail about it
and how to use it putting the pieces
of the frame together was
pretty straightforward. I just added some wood glue on the joints
and then screwed them in place.
And then it was time
to add it to the bottom
of my new cabinet.
I used a couple of long
clamps to hold it in place while I pre-drilled my screw holes.
Because the boards of the frame
are fairly thin, I used a lot more screws than I normally would have
if they were normal sized
boards inside, but I wanted to make sure this would stay on properly
and help keep the piece
sturdy i gave the base a light sanding
with 180 grit sand pad and my surfprep 3x4 ray sander i
didn't want sharp edges on this so i used
the sander to slightly round over the corners and
all of the edges this new base will be painted not stained
and i just put the bottom two drawers in
just to make sure everything cleared
and everything looks great so now it's time to flip
the cabinet right side up again
and get to work on the top i purchased this laminated pine panel
and these are great for replacement tops
when you don't need anything
super fancy i always check
both sides you can see on the underside here there
was quite a few pitch pockets so i ended up using
the other side all i had to do now was just measure the length i wanted
and i had to cut a
little bit off the width as well and i just took it outside
and used my circular saw for that i
flipped the piece upside down again
so that i was able to pre-drill my holes and i had no choice but
to go a little bit on an angle here just
because of the position of the frame but that's okay
just make sure when you're doing this that you don't go too deep i
also used a countersink bit
to create a small pocket for the head of the screw
to fit in so that it didn't interfere with my
drawers at all once i had
the top securely attached i flipped everything right side up again
and got to work sanding the top i used 180 grit
to do so and i did the same rounding of the edges
and corners as I did on the bottom,
but there will be an extra step on this top and it might
be a little controversial.
While I don't know if I can pull off making this piece look 150 years
old, I do want it to look like it's been through some stuff.
I'm going to be painting the drawers
and the base and I'm going to be staining the top.
I'm going to be doing kind of a different
treatment on the handles. I'm not sure yet how it's going
to pan out, but I have to clean them
up first so that's what i'm doing here with a degreaser
and rinsing them off and drying them
so this is a rust kit
that i've had for quite
a while but i've never
actually used it there's
three parts there is a primer there's an iron paint
and then there is the rust activator spray
so the first thing i did was add the primer
and then i did two coats of the iron and it doesn't
have to be perfect as you know rust generally isn't perfect
so there are a few spots here
where a little bit of the primer
is still showing through i'm okay with that
while those are drying i'm going to get to painting this piece
I'm using Fusion Mineral Paint in the color Everett
which is one of their new
colors and a Fusion brush these brushes have
really soft bristles and will make quick work of this I think
it took me about 15 minutes per coat and I did two coats of paint
and of course Nacho had
to come and make sure
everything was good
so once the iron paint had set I went ahead
and used the rust activator spray you're supposed to
spray it on wait five minutes and then spray again
and as you can see here I also did a little bit on
the wheels and then you wait
and this is just a quick time lapse over about 15 minutes you can see
how it takes effect
and while this sort of yellowish color it's cool but it's not quite
what I was expecting it's not quite
what I wanted so I'm gonna experiment a
little bit here I added some dark wax first of all
which would get rid of most
of the yellow again like I said
this is my first time using this so I wasn't
really sure what was gonna happen with it
but I used a little bit of Odie's
safer solvent on a shop towel
and I took it back a bit I removed a little bit of
the wax a little bit of the iron paint
a little bit of the primer and exposed the
metal underneath
and you end up with this really neat worn look almost like
Like, someone's thumb has grabbed this every day
for the last, you know, 50 years.
What's nice about this too is you can sort of tweak it to your liking.
So I didn't have any single pull that was the same as another pull.
Y'all, this is so far outside of what I normally do,
but I'm really having fun with this.
So this is the controversial part I was talking about.
What am I doing with all of these tools?
I am basically trying to age this top.
This is a brand new piece of pine,
and I don't want it to look brand new.
I'm using a bunch of different tools and techniques to gouge,
dent, scrape, and put holes in this wood.
This tool is great for making faux wormholes.
And I could have taken this in a completely different direction
and gone high-end, upscale, modern apothecary,
but I've been looking at that rust kit for a while,
and then I found these, and I just, this is kind of where I ended up.
I'm going to be using two different stains.
Well, three technically, but you'll see in a minute.
First off, I'm starting with Aged Oak by Minwax.
I had a little bit left in this can that I wanted
to use up, and then I opened up a new can.
This is going to give me the lightest tones in this
piece that I'm looking for, and then I'm going
to switch to Coffee, which is a darker color,
making sure to push the stain down into all
those little holes and cracks I created.
You'll see me apply this to the whole top
and then wipe it back in certain areas.
if you think of like an old antique store counter you always have
a darker edge along the front it's
just where things tend to get dirty and grimy
and i'm not trying to copy that exactly but that's
kind of the vibe i'm going for so i left a little bit
of a darker edge around the areas that i
needed to lighten even more i just used a little bit
of the Odorless solvent and wiped the stain
back now that i'm happy
with the top i need
to look at the sides i
could have used a dark wax
or an antiquing wax or a glaze to sort of grunge this up a little bit.
I'm opting to use the same
stain that I initially used on the top which is Aged Oak by Minwax.
It's just going to settle
into what remains of the grain pattern
and I'm going to wipe it right back.
It's time to add
the wheels now to the base.
I'm getting super excited because I'm in the home stretch. I'm
using some of Fusion's beeswax
and hemp oil combo to seal the paint once everything was dry. The
thing I found the top was missing
was that sort of warm amber glow that you
get from old pine as it patinas over time once I get
the paint sealed I'm
gonna work on the top the only thing it's missing
for me is that warm amber
glow and of course not Joe has
to be in the middle of everything so what I
opted to put on the top was a stain
and sealer in one and it's just gonna give
it that nice
warm
patinated
look. Well,
there are so
many things
I wanted
to do with
this set. My
vision for them changed several times
and I ended up with a piece that looks nothing like what I
started with, but I'm super happy with it.
In fact, I'm not even sure I want to sell it. I'm
quite interested to see what you guys think of what I did.
One thing's for sure, this piece is
one of a kind now. I still have to find some drawer liners for these,
so that will be something
you won't see in the reveal, but it is something I have to do.
As always, thank you so much for watching,
don't forget to like and comment if you like
what you see here today, and I will see you next time.