Hardwood Moxon Vise Workbench on a Budget

House Love
61 followers
5 Video Views·Nov 12, 2022
Hardwood Moxon Vise Workbench on a Budget
Today on Catsmoses Woodworking we're going to make this maple and cherry moxin vise for
about a hundred bucks.
Here we go.
So I'm long overdue for a moxin vise.
The last one I made was out of pipe clamps and plywood glued together.
Recently I saw a video that Dustin Penner did a while back and he made this gorgeous
maple and walnut moxin vise using bench crafted hardware and I looked it up and it was about
$338 for the kit before tax and shipping.
So I wanted to figure out if I could build a beautiful hardwood moxin vise with a workbench
in it for under a hundred bucks.
So I figured out two solutions, one's about $120, one's about $80.
The more expensive one uses these zinc hand wheels, three quarter inch all thread, these
nuts and washers, whereas the $85 one uses the same all thread washers and nuts but has
these threaded handles from McMaster Car.
Our next step is going to be to glue up the workbench and cut the vise jaws to their final
size.
Then we're going to drill some holes and start putting everything together.
So let me take you on this journey with me.
Okay, so we've got everything cleaned up and shaped.
We have grooves cut for our legs.
These little tabs that you see on the inside jaw and the legs, that's for clamping down
to the bench or I'm going to drill a hole so if I want, I can screw it down to the bench.
Once we glue these in, that'll give us the exact height for our jaw faces.
We'll trim those down so that way we can drill in the exact center of those so that it doesn't
rack one way or the other when you're clamping.
We're then going to go ahead and drill the holes for our hardware.
The all thread will go through in a three quarter inch hole.
We'll then trace around our nuts, chisel it out.
We're going to use the same sort of order of operations that we used in the ring box
video which is drill a small pilot hole which will give us our locating hole and then we'll
go ahead and drill a series of, we'll use a series of Forstner bits to get the right
size holes for each location.
On our outer jaw, we're going to create a little bit of an oblong hole on the horizontal
plane and that's so that if we have an odd sized piece, it'll taper as needed.
We're going to head on over to the drill press after we glue this up and it is really hot
in here today.
I am killing myself for this project.
I wish we had air conditioner in the shop but this being California, that's just not
the case.
So, He-Man's already taken his shirt off.
I'm going to be close behind but we're going to head over to the drill press.
So here we go.
Okay, so really exciting.
We're almost done.
We just have to attach the back jaw to the table which is all glued up and done.
It's got its clamping locations there and we need to put leather on the front face of
the vise here and then I just want to show you one thing.
When the jaw was extended more than like four inches, I had a problem with a lot of flex
so I made these quick blocks here where I just drilled a three quarter inch hole here.
And so I just screwed those to the back.
I threaded the rod through first and then I put the nut in which you saw.
I decided to go with only one nut and then when it was all the way threaded and closed,
I slid these on and then screwed them into place.
So let's get going on the rest of this and get it finished up.
We'll do some sanding and then at the end of the video I'll give you a demo of how it
all works.
I know you love me.
I see you move.
You've been talking to me three nights in a row.
I think it's just lose control, because life's too short
for yapping.
Your dream.
You've been talking to me.
Woo!
What a cool build, guys.
This was so much fun to do.
Wow, it's hard to do backwards.
This was so much fun to do.
I had just a blast building this.
And to build a Mox and Vise for under $100,
that's just incredible.
The setup as is is about $100 with the zinc-plated hand
wheels, the 3 1⁄4-inch all-thread,
two 3 1⁄4-inch washers, and two 3 1⁄4-inch nuts.
I splurged a little bit, and I bought these tapered washers.
They were about, I don't know, $16 a piece.
And you can see the way they work here.
The inner washer is tapered.
So if you have an odd-shaped piece in there
and you clamp it, it allows the jaw
to really clamp sideways.
The vise itself is just incredible.
It's cherry and maple.
Solid as a rock.
And it really, everything works so smoothly.
I didn't need to oil anything.
These spin so easily.
Let me give you a little tour, and we'll kick the tires.
We've got the 4 1⁄2-inch zinc-plated hand
wheels with the hand crank here.
They have a set screw, and I drilled a little divot
into the all-thread so that they would stick real firmly.
It wasn't really needed, but I thought,
just in case, over time.
I put these wings on here for clamping.
But I also drilled some holes in them
and put screws so that we didn't have
to worry about it coming up if I wanted
to screw it to my bench.
These are $6 hand wheels here that you
could use that would get that price under $100.
Really, one of the things that makes everything so smooth
is these blocks I made.
I drilled 3 1⁄4-inch holes through them
and screwed them to the back.
And that sort of adds a little cantilever
to the all-thread, which keeps it from binding up
when the jaws are wide open.
Yeah, I mean, look at these things.
They just crank so easy.
And they're just so smooth.
So thanks, everybody, for watching.
It's just so much fun.
Please comment.
All your comments are read, appreciated.
I respond to most everything.
And your support just means the world to me.
Check me out on Instagram.
We've got a lot of great things coming up.
I have a CNC being delivered Monday.
We're going to start getting into that.
We have some really cool builds on the horizon.
So thank you so much for watching,
and have a wonderful day.
