I tried to save this OLD, CRUSTY, DAMAGED oak piece : Restoring Furniture

Trash To Treasure
3 followers
This old quarter sawn oak table (whatever it is) was heavily damaged, wobbly, and in need of repairs and full refinishing. I did what I could for it, and made a custom stain using Odie's Oil & pigments.
#furnitureflipping #furniturerestoration #antiquefurniture #refinishingfurniture #restoredfurniture #oakfurniture #relaxingrestoration #transcendfurnituregallery
AI Generated·May contain errors
Video Summary
AI GeneratedThis video documents the comprehensive restoration of a vintage quarter-sawn oak table. The creator transforms a severely neglected piece—plagued by water damage, rusted hardware, and structural instability—into a refined mission-style furniture piece through meticulous disassembly, chemical treatments, and custom finishing.
This video is sponsored by Woodworkers Guild of America.
I don't really even know where to begin with this one you guys but I guess
first thing I need to do is get this home. Now as it was it was about half an inch too
wide for my jeep so I ended up having to pull those trim pieces off the top.
As you can see this piece is very very well used
and clearly upkeep on this has been neglected for quite some time.
It's super wobbly. There are stains all over this. There's hardly any finish left on it.
I don't know exactly what this piece was. It seems like it might have been used in a kitchen
or something like that. Someone may have had plants on this. I don't know but there is a
ton of water damage and rusted nails and hardware. I have no idea why they chose to stain these
drawers so dark and they are stained. It's going to be really hard to get that out so
they're probably going to have to stay dark. This piece is put together mainly with dowels.
A little bit of wood glue which you can see is failing absolutely everywhere which is why the
joints are loose and this piece is wobbling all over the place. So really the only way to deal
with this is going to be to completely disassemble it. Take it apart piece by piece. Clean each
individual piece up. Make any repairs to the wood. Replace any nails or hardware that need
to come out. Dowels etc. Now this piece clearly used to be on casters which would have fit right
in here. The casters are gone. No idea what happened to them. With casters this piece would
become very tall. It's already quite tall. So yeah if you have any idea what this piece would
have been used for feel free to let me know down below what you think. These legs are extremely
rusted. There is water damage on the wood itself and then the hardware is really rusty.
I don't know if I want to put casters on this. It's already quite a tall piece but we'll see.
At any rate these have to come off so that I can refinish the legs. And clean up these really
pretty brass caps. Each cap is held on by two small brass nails so I need to pull that out
then remove the caster insert which is no easy task especially when it's rusted and the metal
is kind of frail. I get all these off and they are immediately going to go into a rust bath for a
while. An alternative to this would be to put them in some vinegar that is boiling for a little
while. That does often help loosen up the grime and deal with rust. There's no maker's mark on
this piece. It's very clearly completely handmade. I wouldn't say this is a factory piece. As I'm
pulling these off though I need to indicate how these actually go back in so my arrow always
points to the front and then I indicate whether it's left or right blah blah blah. There's a
sneak peek of an upcoming project in the back there. Someone has gone and put some diagonal
nails in probably to try to shore this thing up because as I said it is super wobbly. The problem
with this is everywhere they've driven these nails into has split the wood. This is made of
quarter sawn oak. It's an extremely hard wood. You can't just hammer especially thicker nails
in without splitting it. You have to pre-drill a hole. If you're going to do that at all please
stop using nails as a means to try to repair joints. It just doesn't work and can often damage
the piece further as you can see. So as I move into the drawer assembly here at the bottom this
is very interesting. You can see that there are nails everywhere. There's three random flat head
screws. There's two here in this middle section and then one randomly on one side. I find it
unlikely that those would be original and I just snapped a nail there. It was so rusted it just
broke off so that'll be fun to get out later. I don't think the screws are original because
they're not strategically placed. They're just very random. This is a solid wood piece so you
have to account for a wood movement which is why this piece is not put together with a ton of
screws. There is of course a way to use screws in a piece like this and that is simply making sure
the head of the screw has a widened up hole. You just have to account for the movement of the head
of the screw as those larger panels like on the top there you see expand and contract with the
seasons and temperature and humidity. The wood glue in this assembly here that I'm tapping these
nails out of has completely failed in every joint except for one so I'm gonna have to glue all this
back together after I get it all cleaned up. Now videos like this are in part made possible by
sponsors like today's sponsor Woodworkers Guild of America. I've worked with them on a few videos
in the past and I've really been enjoying my time learning about woodworking. They were a source of
inspiration when I redid my office not long ago. Kind of an offshoot of what I do but yet it's also
integral especially when I'm dealing with pieces like I'm dealing with here where I have to take
things apart put them back together. My big computer monitor is being replaced so I'm watching
on my laptop right now but I'm checking out this awesome video on router techniques where they're
comparing different routers and the pros and cons of each. You guys know that I was a little hesitant
initially with my router but I'm getting more confident with it and I built a small little
temporary router table but I want to build a bigger one so I'm trying to get some ideas for that.
Woodworkers Guild of America is your go-to online resource for all things woodworking. Whether
you're looking for inspiration for a new project, learning about a new tool, or truly wanting to
master your craft. As a member you'll have access to their entire video catalog as well as their
live streaming tutorials and Q&A's where you can actually interact with the instructors in real
time. Right now the first 1000 people to click the link in the video description below will get a
full year of premium membership to Woodworkers Guild of America for only $1.49. This is truly a
fantastic opportunity to experience the joy of creating something with your own two hands.
So after these had sat in the rust bath for a little while and I very gently tried to scrub
some of the surface crap off it became apparent that the grime was a little bit thicker than
anticipated. Now had I used the boiling vinegar method that would have loosened that grime but
here I'm just using my Dremel and a fine wire brush because this is brass you don't want to
use anything that's going to scratch it but that was enough to get some of that crud off and I'm
super happy with how these came out. I do want to protect them though especially where they're on
the floor they're susceptible to water damage. So this is a metal safe rust coating it's just
a clear coat it's going to protect it from more water damage or tarnish over time. There's also
a type of lacquer that you can get for the same purpose. I'll flip these over and do the other
side once it's dry. So I don't want to put rusty nails back in this so I've found some replacement
nails but they're obviously very shiny and I don't really want that in a piece that's older.
So I'm going to be using this product to sort of chemically alter the nails and give them a bit of
a patina. This is called gun bluing it's technically a form of oxidation but it's great for turning
certain metals dark. As soon as it changes color you want to rinse them dry them and apply some
sort of oil. It will help it from immediately rusting. I'm going to do that with these small
finished nails as well. Yeah nails like these I don't really want to put back in this piece.
There were a few repairs I had to make especially in areas where there are grooves. The glue joints
have just completely failed over time so after scraping out the old glue I applied some new hide
glue and reattached all these parts and clamped them. I wanted to say a big thank you to an amazing
viewer for sending me these bluetooth headphones from my wishlist on Amazon. I've been listening
to a ton of Mr. Ballin here on YouTube while I'm working. A lot of you guys know I'm fairly
sensitive to certain sounds in my shop like scraping for example so these are a great addition
to my workroom. Like I mentioned there's not a ton of finish left especially on the legs here for
some reason but there is a little bit and there's also some old crud on here that I want to get off
because I don't want to sand any of this down into the wood. There's not a lot of point in using a
chemical stripper on this because there's hardly any finish and that's mainly what it removes
and I also don't really want to use a cleaner on the raw wood so scraping is the best option here
Now you guys know how much I love my surf prep sander. This is a new one I wanted to try out. I
really miss having a 5 inch sander on larger pieces. I had to order some replacement supplies
anyway so I thought I would give this sander a try. This is the 5 inch electric ray gen 2 plus
sander and they have two options available. They come in a 3 16th inch and a 3 32nd inch. Now what
that means those sizes are the measurement of the orbital path so basically the size of the
circles that it makes. When trying to decide which to go with I had to look at what I would
personally be using it for. The majority of the pieces I work on I remove the finish whether it's
chemically stripping or scraping. Because of that the 3 16th inch sander was probably not the best
for me. I would be better off with the 3 32nd inch. It's hard to say I get a little tongue-tied
but the main difference is the 3 16th inch one is meant more for trying to smooth down rougher wood.
It has a little more bite and it kind of helps you work through those rough layers faster. The one
that I opted to use is better for finishing so once everything is nice and smooth then you come
in with your finishing sander and you get that nice buttery soft sanding and in a perfect world
where I had a million dollars I would get both but it was kind of one or the other this is the
one I opted to go with. There's a lot of consideration that goes into picking out a
sander. I know a lot of beginners think oh I'll just go to Home Depot and pick up a sander and
there's nothing wrong with the sanders at Home Depot but you have to take those things into
consideration like the stroke length on these orbital sanders. If you recently bought a sander
and you're having a hard time getting a nice smooth finish at the end it could be that you
have the more aggressive sander. On the flip side if your sander is not cutting through those rougher
layers like it should be even with a lower grit it could be that you have something that is better
suited to finishing and let me say too it has nothing to do with price. You can get a really
nice sander for about a hundred bucks or you can spend twelve hundred dollars and get a top-of-the-line
sander and if you're not getting the right sander for what you're using it for you're not going to
have good results so it's important to take these things into consideration. I've been thinking about
doing a video on this for a long time now I know a lot of the people that watch my videos don't do
furniture but there are quite a few of you that do so if this is something you'd be interested in
having me talk about let me know down below and I'll see if I can put something together for you
guys. Okay so while I was explaining all that I was scraping what was left of the old finish off
these shelves and doing my first sanding and my sanding was 150 grit because there was hardly
any finish so I didn't really need anything super aggressive. These are solid wood and not veneer so
it's not like I had to worry about sanding too much but there's no point in sanding more than
you have to and sometimes when you have pieces like this where you've got interlocking joints
if you sand too much those joints might not fit together quite as nicely as they did before so
something to think about. You can see I'm using the pencil trick here this just helps me get a nice
smooth and even finish it helps prevent me from over sanding in some spots or under sanding
and it also lets me know if I'm moving up in grit properly. So this is the top and this was the worst
stained one of all three shelves you can see there are some water marks some rust spots from the
nails some of these look like there might even be grease spots I'm not sure there's a couple
little gaps too it's not all the way through the board it's just on the very top so I'm going to be
using a filler in that but before I do that I'm going to be doing an oxalic acid treatment on the
top. This is great for getting rid of dark organic stains like water stains and adding water to the
top might actually swell the fibers a little bit helping release some of the dents that are in the
wood and might even close up that gap just a little bit more. I'm going to be applying it to all three
shelves even though the top is the worst I want to make sure that this is as even as possible so
this is after the oxalic acid has been rinsed and then the board has completely dried you can see
a lot of the stains did come out but not all of them not 100% anyway that's to be expected so I'm
just doing a 180 grit then I am going to apply a little bit of filler in that crack which did close
up a little bit and I'll do my final sanding of 220 after that. So once my final sanding is done
I need to clean this up in preparation for finish. Now I'm using some compressed air to blow all of
that sawdust out of the rather large pores in the oak probably a little bit hard to tell what this
looks like on camera but if you look closely you can kind of see that dust blowing out of there
just make sure you wear a mask if you try something like this. Now moving on to the drawers you can see
that the drawer box itself is rather dark it is a very dark stain that they have on there I'm not
why they made that choice but I am actually going to take this drawer completely apart
sand it all down put it back together and then I'm going to be re-staining it and to avoid having to
sand a ton of this to get all of that old stain out I'm actually going to be staining the inside
dark again. To do this I need to pop the nails up from the bottom and just gently tap it open
I ended up using some hide glue to put it all back together and here we are now I'm adding some
water-based stain in the color dark oak to give it a similar look to what it had before
but just slightly warmer and I think this is going to go a lot better with what I have in
mind for the finish. Now on the left here is the original drawer in its original finish
and on the right is the drawer with the face still sanded not finished yet but you can see
the difference in the color and uniformity and it just looks so much cleaner. So it's time to
put this all back together now some of you might be wondering why I didn't stain everything while
it was apart and the main reason for this is there are some areas I needed to use glue and
I didn't want to have to deal with glue not adhering to parts that have been oiled so in
this situation it makes more sense to put it back together and then stain it. I'm not a huge fan of
this trim on the top but it is original to the piece so I'm going to add it back on. I didn't
glue these trim pieces on the top I just tapped them in with some nails and then used a nail set
to just slightly lower that nail head. Once this is all put together I'm going to go ahead and make
my stain. Now I'm using some safer solvent from Odie's oil some super duper everlasting oil and
these two pigments to make a custom stain. I'm trying to emulate or mimic that sort of arts and
crafts mission style oak. It's not really one of my favorite things but I think it's going to work
really well for this piece. It's going to warm it up and color just works really well with this
specific wood. I'm using a little bit more of the aged blondes powder because I don't want this to
be too dark. There's no specific recipe for mixing a stain with Odie's oil and pigments. It's completely
customizable so you can make it as translucent or opaque as you like and this is the color that
it's going to look like. So once I've stirred that up really well giving it a shake I'm just using a
white non-woven pad to apply this. Sometimes I use the Merck and Roland pads which are gray
same thing it's just this is what I have on hand. So what's nice about these particular stains is
you don't have to worry about lap marks. So you can see where I've left the stain there in the middle
of the top. You could never do that with a normal penetrating oil. You would have a mark when you
went back to finish. These stains are super forgiving. I love that you can tweak it and get
it exactly what you want and with the Odie's you apply it over the entire thing let it sit for a
little bit and then wipe it back. In terms of wiping it back I'm just using shop towels. You can use a
terry towel as well but you need to make sure you get all of the excess oil off really really well.
I'm going to let this sit for a couple of days and then I'm going to add a coat of the Odie's
wood butter just for a little added protection and a kind of nice soft luster. The medullary
rays in this oak are just phenomenal. What a beautiful piece and I don't want you to think
that I forgot the underside too because once the top was all done I actually flipped this upside
down and I sealed the underside as well. Now as far as this hardware goes this one on the left I've
already cleaned and polished. The one on the right is original. So to start off I'm using some brass
oak just to clean the outer surface dust and oils from people's hands over the years. It's pretty
good but look at the one on the left. It's so much shinier and that's because I went a step further
and used a polish. Now this flits polish. It is amazing you guys for brass and it's super safe.
Put it on just like you would with brass oak and it does a really good job of removing tarnish
specifically. They say to use a microfiber towel. I'm just using a shop towel that seemed to do just
fine and this looks so so much better. This hardware has dings and marks all over it. It's vintage
that's fine but I just wanted to clean this up a bit. So here you can see the piece upside down.
This is me doing the underside and just caught a little bit of the towel there. The undersides are
always pretty much always a little bit rougher. They're not sanded as finely so that's why it
caught a little bit of my towel there. Now you remember these leg caps. I made sure to put these
back on the exact leg it came from because the nail holes line up perfectly. Now I'm torn. Do you
think I should add new casters to this or not? It'll raise the height by a little bit. It's already
a fairly tall table. I don't really know what this was made for. Some people think a baby changing
table. Some say garden table. I personally think maybe it was used in the kitchen. I don't know
but let me know down below if you think I should add casters on this or not.
So to do this transformation I scraped the old finish off. I used my surf prep sanders,
a round of oxalic acid, some bar keeper's friend and again that flitz polish. If you do any kind
of furniture stuff you gotta check that out. I also used this trim clad clear rust paint on the
feet specifically. I used this perma blue gun bluing solution to turn ordinary nails dark to
kind of make it go along with the piece a little bit better. I used old brown glue which is a high
glue for my repairs. Timbermate wood filler to fill a couple small holes. This is that cement
water-based stain that I used on the inside of the drawers and then of course the oldies oil,
safer solvent, super duper everlasting oil and two colors. I used southern pecan and aged bronze to
my stain and then the wood butter at the end which I didn't show is exactly the same process
as the odies oil. I also used these white non-woven pads to apply the stain and odies and polish the
hardware. Okay let's have a look back at what I started with. This thing was super rough. Every
section of it had finish damage, water damage, marks and scuffs. It was super wobbly. Now first
thing, any table with this sort of legs is going to be slightly wobbly but this was exceptionally
wobbly. Pretty much every joint was loose but as always I am here to show you that all is not lost.
With some time and effort even this pile of crap can be beautiful. Enjoy the reveal and I'll see
you next time!
