The 555 timer IC is an integrated circuit that is used in a variety of timer circuits, pulse generators and oscillator applications. The heart of the tutorial is the 555 timer IC that is wired as an astable multivibrator.
In this tutorial, I'll first blink "an LED" using the positive pulse generated by a "DIY 555 Pulse Generator Module" (video: https://youtu.be/bMAnipPOjFo), followed by "two LEDs" alternating and flashing at a regular interval. The output frequency of pulses can be adjusted using a potentiometer. The circuit can be operated from any voltage between 5 to 15 volt DC.
Watch this video for detailed step by step instructions on how to build this circuit and for a complete instruction on how the circuit works.
Support My Work BTC: 1M1PdxVxSTPLoMK91XnvEPksVuAa4J4dDp LTC: MQFkVkWimYngMwp5SMuSbMP4ADStjysstm DOGE: DDe7Fws24zf7acZevoT8uERnmisiHwR5st ETH: 0x939aa4e13ecb4b46663c8017986abc0d204cde60 BAT: 0x939aa4e13ecb4b46663c8017986abc0d204cde60 LBC: bZ8ANEJFsd2MNFfpoxBhtFNPboh7PmD7M2 Thanks, ca again in my next tutorial.
The 555 timer IC is an integrated circuit that is used in a variety of timer circuits,
pulse generators and oscillator applications. The heart of this tutorial is the 555 timer IC
that is wired as an astable multivibrator. In this tutorial, I'll first blink an LED
using the positive pulse generated by a DIY 555 pulse generator module, followed by two
LEDs alternating and flashing at a regular interval. The output frequency of pulses can
be adjusted using a potentiometer. The circuit can be operated from any voltage between 5-15V
DC. Watch this video for detailed step-by-step instruction on how to build this circuit and
for a complete instruction on how this circuit works.
This video is sponsored by PCBWay. PCBWay specializes in manufacturing of very high
quality, low volume, colored PCBs at a very budgetary price. In addition to standard PCBs,
you can order advanced PCBs, aluminum PCBs, rigid flex PCBs. They also provide PCB assembly
and other related services which can meet your need at the greatest extent.
For this tutorial, we need two LEDs, one 555 timer IC, one 10uF capacitor, one 220ohm resistor,
one 1kΩ resistor, one 10kΩ resistor and a 10kΩ potentiometer.
The circuit is very simple. By connecting pin number 2 and 6 of the 555 timer IC,
we put the IC in a A-stable mode. In A-stable mode, the 555 timer IC acts as an oscillator,
re-triggering itself generating square waves at pin number 3. By changing the value of R1,
R2 and C3, we can change the frequency of output pulse generated at pin number 3.
Let me explain this with the help of an animation.
When pin number 2 of the IC detects voltage less than one-third of the supply voltage,
it turns on the output. When pin number 6 detects voltage more than two-third of the supply voltage,
it turns off the output. And when the output is off, the discharged pin, pin 7 gets
internally grounded. This is how the trigger pin, pin 2 and the threshold pin, pin 6 of the 555
timer IC senses voltage and controls the output at pin number 3. Capacitor C1 will be in discharge
state immediately after firing up the circuit. So the voltage at pin number 2 will be zero volt,
which is less than one-third of the supply voltage. This will turn on the output on pin number 3.
At the same time, pin number 7 will internally disconnect from the ground and the capacitor C1
will start charging via the resistor R1 and R2. Once the voltage across the capacitor C1
crosses two-third of the supply voltage, pin number 6 turns off the output. At the same time,
pin number 7 will internally reconnect to ground causing the capacitor C1 to discharge via the
resistor R1. Once the voltage across the capacitor C1 falls below one-third of the supply voltage,
pin number 2 turns on the output and the above cycle continues. Since resistance R1 is involved
in both charging and discharging of the capacitor, increasing or decreasing its value will increase
or decrease the duration of the off cycle and will decrease or increase the flashing rate of the LED
as the capacitor will take more time to charge and discharge. By replacing the capacitor with a
higher or lower value, you can also get a longer or shorter flashing rate. By replacing the resistor
R1 with a potentiometer, the blinking rate of the LED can be dynamically adjusted.
Now to get the dual LED flashing effect, you need to connect a second LED with opposite
polarity to pin number 3 of the IC. That's it. Easy as that. Now let's calculate the output
frequency and the duty cycle of the output waveform. In my setup, I have resistance R1
equal to 1 kilo ohm, R2 as 10 kilo ohm and capacitor C as 10 microfarad. There are many
online calculators to calculate this online. I'll provide a link to one of the A-stable calculators
in the description below. Let's first calculate the value of T1 or the capacitor charge on time
which is 0.693 R1 plus R2 into C3. Putting the values together, we get 76.23 milliseconds.
Now for capacitor discharge off time or T2, we need to multiply 0.693 to R2 and C3 which then
gives a value of 69.3 milliseconds. Next the total periodic time T is equal to T1 plus T2
which comes out to be 145.23 milliseconds. The output frequency f is therefore 6.871 hertz
which gives a duty cycle value of 52.38 percent. If you want to have more control over the charging
and discharging, use a higher value of R2, 100k and a lower value of R1, 1k. That way you will
have 99 percent control over the charging and discharging resistance of the circuit.
To make it easy for you guys, I've created this tiny little 555 pulse generator module.
After assembling the components, you just need to power this module by providing a voltage between
5 to 15 volts to get an oscillating output at the pulse pin. So this is how my board looks like in
2D and 3D. There are 16 breakout boards in this 100 centimeter by 100 centimeter assembly. You can
download the Gerber file from the link provided in the description below and order it from PCBWay.
Before moving forward, let me quickly show you guys how to assemble the components to this custom
made board. Let's start by soldering the IC base to the board. Then let's solder the potentiometer
to the board. After that, let's solder the 1 kilo ohm resistor to the board followed by the 10
microfarad capacitor to the board. Once done, let's insert the 555 timer IC to the IC base.
To conclude the setup, I have soldered three male pin headers to the board.
This circuit can be used to control the speed of DC motors and stepper motors. It can be used
to control the windscreen wiper motor to generate the to and from motion. It can be used as a square
wave signal generator. It can be used as an adjustable pulse generator for MCUs in strobe
and SOS signaling circuits, telecommunication for encoding purposes, in turning indicator circuits
for all type of vehicles and bicycles to generate adjustable pulse to control other circuits as in
combination with 4017 and 4026 ICs. I have used this IC in few of my other projects and tutorials
like the DIY Boba Fett helmet with LED chaser circuit, LED chaser circuit using IC4017 and
Arduino, DIY LAN cable tester and 555 pulse generator module. Thanks again for watching this
video. I hope it helps you. If you want to support me, you can subscribe to my channel
and watch my other videos. Thanks. See you again in my next video. Bye now.